Alsmotorrad Bmw

Пікірлер

@alanrichardson1672 Ай бұрын

To secure the butterfly fasteners it would be better and more professional to use threadlock. If one of those nuts or screws finds its way into the cylinder it would do a huge amount of damage to the engine.

@andrewloeffler432 Ай бұрын

I don't think the engineer who designed this could have made it more complicated. I removed around 30 screws and still struggled with the airbox lid. Ridiculous . I'm guessing that they hope the consumer just gives up and brings the bike to the stealership

@fawziarar2661 5 ай бұрын

Vidéo très propre simple efficace !

@bartomiejkapczynski3194 6 ай бұрын

Height of new entire plate stack is 44,36mm, anyone know when to change plates? 1,86mm less qualifies for change or?

@davidhaney1394 6 ай бұрын

throttle body sync , isnt recommended , its a MUST .

@HK-nl3ih 6 ай бұрын

What are the symptoms that this rebuilding will fix?

@gazzagazza1000 6 ай бұрын

Exultant video

@kaffedyret 8 ай бұрын

Fantastic good video - Thank you for that :)

@Motivational_Lifequotes1111 8 ай бұрын

Where would I get the soldering stuff from?

@Motivational_Lifequotes1111 8 ай бұрын

Yeah I broke one :(

@Motivational_Lifequotes1111 8 ай бұрын

Can I order them ? If so Amazon has them but idk if they would work

@rikpawlus 9 ай бұрын

Hi where to set Jack to lift rear axle in one go

@baristasmaestro2240 9 ай бұрын

Sorry but your video missed something important, the steel plates the one side is different from the other, do you know that? maybe you have done damage allready, if you dont know how is better to go to find someone who knows.

@narcissistinjurygiver2932 10 ай бұрын

how much do these clutch parts cost? can they be had aftermarket?

@stanza77 11 ай бұрын

My slave cylinder will not sit flush, please help!!

@tassoskard8157 Жыл бұрын

Hello, is there a link or something for the repair kits? I am afraid that I cannot find them anywhere

@GerriHildebrand Жыл бұрын

Dont the pistons need to be compressed again

@mattiristola3434 Жыл бұрын

I installed this Dan Cãtan Throttle Body Rebuild kit myself on my 2000 BMW yesterday The task was quite simple, and only the removal of these original slide bearings, which had been in place for over 20 years, was a bit of a challenge. It was difficult until I realized that an 8mm bolt sawed into a 20mm slot on one end would work very well as a bearing removal tool ;-) Also, I noticed when disassembling my own BMW that the pulley ends didn't have the shims Dan Cãta described that I had to find elsewhere, so the mounting shoulders for that axle would have been perfect for another installation in the future. Otherwise, this operation was easy to do, and the end result now completely satisfies me. Different from the way of making this video, I myself used the old bearings as a "spacer" according to Dan Cãta's advice when installing the new bearings, as well as a long 8mm bolt that extended completely through both holes, so the chances of failure were minimized when the new bearings were hammered into place. The original problem was the TPS which I could not adjust to the set margins under all conditions and now works 100% fine.

@tassoskard8157 Жыл бұрын

Can you please advise from where did you get the repair kit?

@mobyhunr Жыл бұрын

loc tite

@nemanjaneso96 Жыл бұрын

Excellent video, thanks bro !

@dronepilot260rc Жыл бұрын

I’m going to be doing the clutch on my 2003 and 2006 k1200 GT’s

@lethal_larry Жыл бұрын

video would be half the length without all the "uhhs uhms"

@tomluciani3723 Жыл бұрын

6-hours to change an air filter disassembling this plastic...unacceptable! I am selling this fiasco!

@armandeus Жыл бұрын

My BMW x3 2014 328i don’t have the LED board 😮

@voolandis89 Жыл бұрын

Can anyone confirm this works for F11?

@gentlemansbusa2985 2 жыл бұрын

Please link me where the hell you found that 30mm socket.

@ВладимирВахутин 2 жыл бұрын

Да хренле у вас там эти оси стоют копейки хоть каждый сезон меняй, у нас в России попробуй. Стоимость такая что купить мопед на эти деньги можно.

@nicadair7700 2 жыл бұрын

Soldering the board is not a permanent fix, the whole board should be changed with a more reliable circuit board to feed the LEDs. LDD-500HW is what you require.

@LexuzzMC 2 жыл бұрын

nice job)

@alebsoio 2 жыл бұрын

Thanks

@niveselva4373 2 жыл бұрын

Do the pistons not need winding back?

@OscarFoianini 2 жыл бұрын

Great video !!! Would you recommend the Barnett Clutch Kit?

@msi4226 2 жыл бұрын

Buddy, where do we buy that ballast?

@Filipediasalmeida 2 жыл бұрын

great video on the throttle body rebuild! thanks for sharing!

@888jannn 2 жыл бұрын

Nice job... thanks...👏👏👏

@gabidagon 2 жыл бұрын

I’d like to only change the spring, i can leave the position sensor in place in order to avoid adjusting it?

@Antimortem 2 жыл бұрын

❤️👍

@Flowsalvador 2 жыл бұрын

Thanks you...!!!

@Enonymouse_ 2 жыл бұрын

If you call up and ask bmw dealer, they won't have any clue about this. If they did, they were not willing to tell me.

@SmokysRides Жыл бұрын

Then they are idiots because the procedure is detailed in the service manual

@foreststone855 2 жыл бұрын

Thanks, really appreciate your video, easy fixing!

@barkingshark6413 2 жыл бұрын

Can barely hear it...

@offroadtales 2 жыл бұрын

Thanks. BTW, if you look at the cams, they have a flat surface, if both are aligned with each other (with a ruler for ex) so no straw is needed...

@blessroberts5776 3 жыл бұрын

3 of the 4 taillights went out. I rempved all 4 and to my surprise not one has this LED chip board in it, or even a spot for it. Please help if you can. X3 2013