Warning: it does not work with newer E010 boards that have the label JR-NH010R5 It only works with the older JR-NH010R board which flies better too.

Hi, is this module work with x9d plus se 2019? I wanna get for eachine qx65. Fc is eachine beecore v2.

The video doesn't explain very well the process of making this module to work as it was already installed and that is kind of confusing for most people. Anyway thanks for the video as it covered most of the storry :) In my case the GREEN light doesn't went on or blinking whatever I do, I thought the module is DOA. But after watching a few more videos and reading on the forums I think I sorted out where the problem is. I have tried different firmwares fo my Taranis X9D+ (now with Opentx 2.1.9) and I found that for making it work the firmware is not so important but the exact next steps are the key: 1. Mount the module 2. Power the transmitter ON 3. Create new model 4. Go to the settings of the new model and set the Internal transmitter OFF 5. Go to the Mixer settings and set channels order to be AETR 6. Power OFF the Taranis 7. Power ON the Taranis 8. Go to the settings of the new model and set External transmitter ON 9. Set the External transmitter settings as per the video - PPM, CH1 - CH12 10. Power OFF the Taranis 11. Power ON the Taranis and in a few seconds you'll see the GREEN light blinking Now it's time for binding 12. Power OFF the Taranis 13. Power on the QUAD 14. Set sticks positions for binding and Power ON the Taranis If the quad is supported and you had the right sticks combination for binding then the quad lights will indicate that it's bind to the transmitter. Now you are ready to fly :)

Dude, yes!

So very useful!!! Thanks! I have a small fleet of those toys and a TQX7!

how about mode 3 transmitters? thx

No Problem binding to a Syma X22W. Works great

Ich glaube, heute laufen nur noch Psychopaten rum.

I got the module to work!! But do I have to remove it to go back to flying my other quads?

So i must open the mainboard first? I have qx7 reciever what should i do, is the same way works for qx7 ? Thanks

Will it work with the Hubsan X4 h107c on my Taranis Qx7?

Can you tell me which stick pattern work with my jjrc h67?

How did you remove the bell? I removed the screw on the bottom but it won't come off.

How is this compare to smt32 4 in 1 multiprotocol module?

Hero of my childhood :-)

David 💪

Thanks for sharing - to bad this was a shortened version - did it sound as good inside the venue as it does in this video? #HasselhoffOurHero #30YearsLookingForFreedom

Thanks for giving credit to the programmer.

Ist das am Ende Nino von DCN? xD

WARNING TO EVERYBODY: Carefull, there are tons of fake motors out now (banggood, etc.). The airgap is bigger, thinner/weaker magnets, bad bearings, bad CNC machining, different bell design, balanced like shiiiiiiiit, different aluminium type, different weight. But BG refunded me at least. Now I will try out directly from the "Official AOKFLY shop" at Aliexpress.

Why did you need to change motor timing to mid-high?

Works with the E011 too, protocol selection is pitch up and to the right, throttle all the way down while switching on taranis. (right stick up and to the right, left stick down, if you fly with a mode 2 radio) you have to have your mixer channels set to AETR, inputs can stay the same. flips are on channel 6, headless on channel 8 and rebind on channel 12, don't rebind while flying. FLY HARD

are these brushless motors?

What Lipo?

Data looks really high amp draw though?

I can't believe it's available here: www.banggood.com/Eachine-E010-Mini-2_4G-4CH-6-Axis-Headless-Mode-RC-Quadcopter-RTF-p-1066972.html?p=O2190714410847201709 I hope this can help you kzbin.info/www/bejne/l4aqfWOjlJuUack

can you do the same with h8 model?

Hey Mika I fly the 2205 2500KV AOK motor and they scream on 4s, they have an Aliexpress shop which is cheaper than Banggood, check it out..:-)) nice review..

Really GOOD motors! Flied them in my last videos! Check it out! They SCREAM :D

good

schade nicht in deutsch

Multiprotocol TX Module + Turnigy 9XR works, but DM003 Mini Speed Flight 2.4G 4CH 6Axis 3D Roll RC Quadcopter RTF does not work :(

nice! will they handle 5s?

Nice

Nettes Review! :-)

Nice review!

Will it works with the FuriBee F36?

Klasse Video, schöne erklärt. Leider habe ich das Problem das es bei mir nicht funktioniert. 1000mal probiert. Die grüne Lampe geht nicht an. Bangood hat mir jetzt einen zweiten zugesand. Leider das gleiche Problem! Hast du da vielleicht eine Idee? Woran kann es liegen. Die Taranis ist ca. 1Monat alt.

By 3:35 I had already placed my order.. you sir are a salesman jedi.

Will it work with eachine i6 remote

Thanks for sharing this video. I only wish you would answer some of the very valid questions below!

Anyone know the protocol for the Blade Proto-X?

He Mika can you help me out with the module? I've ordered two of them from BG but both are not working, the green led is not lighting up. Doing something wrong, i'm using Taranis Plus. Thank you!

Useless 'how to' if you're not going to show us how to do the binding!

mir gefällt der startsound deiner Taranis. könntest du mir den mp3 File senden?

Excellent Video Mika. Thank You. Followed it and got it to work on my Taranis QX7. Qs 1) How do I get it to autobind so that I dont have to restart the Radio everytime.

Hi Mika, I have used this module on QX7 and binds just fine with E010. The binding instruction sheet lists many models supported. I tried with my JJRC H20 hexacopter and it does not bid, not matter what I try. The module is on with green light and set to PPM and 1-12ch just like for the E010. My guess is the the binding instruction sheet may be wrong for this model. Any ideas on this one? Thanks