it would greatly help if you used to correct terminology when discussing these issues. You have an EJECTION issue. not an extraction issue. and you keep calling the EJECTOR, the extractor. your issue is those trash extractors you are using. There is a reason every single aftermarket manufacturer for the 10/22 make their own extractors. First thing you replace on ANY factory 10/22 is the extractor. 2nd is the trigger. 3rd is the mag release.

How about putting a piece of white paper behind it So we could see it better.

thanks for info. i have been going nuts with the back lights. i should have known, when you have a question or problem go to youtube. they have taken over from all the old motor heads that we use to ask for help. thanks again.

Do you by chance have a part number for that bearing?

When my 10 22 original extractor was worn-out it wouldn't extract live rounds from the chamber probably because of carbon ring at the front of a tight match chamber. The bullet would get stuck. an aftermarket carbon steel extractor fixed the problem. it probably came with a new spring as well. Don't remember

Damn. Nice job.

Does the truck have to be moving forward to engage in 4+4

Is this scooter worth the 2200$?

💯💯💯💯

Thank you sir

Have you tried 7018 3/16?

You could have cut the weight in the floor down by using deck board

Do you have to disconnect the battery before doing this repair Is it the same if the rpm gauge is not working?

Thank You!

So, I have a 15-8 that doesn’t have the holes… my mount just showed up

Thank you for showing the actual process of unboxing it! I was trying so hard to put everything back into the box, and your video is super helpful.

I just ordered mine yesterday can’t wait to get it! What kind of helmet do you wear? And how much should I spend on it?

Corona del differenziale centrale in plastica?

Worst way to take a case apart how You're prying on the edge can easily damage the seal area of the servo case How I do it is hold the servo with your fingers only supporting the tabs underneath side of servo tabs and hit/tap the gear with a small brass/plastic headed hammer and the large part of the servo will drop off the top. hold only underneath the servo mounting tabs and hitting the horn mounting gear with the hammer to knock it out of top case this is also how you remove top to get to gears if you have a stuck bearing that has been rusted and damaged from water try it next time it'll be much easier and not damage anything

The foot bord looks very short and not very wide.

Did you have check engine light at the same time??

May I ask what the symptoms were? I have a bad shake in mine at speeds 35-40mph and up also has the roar of a wheel bearing but I have checked the wheel bearing and it is tight and moves freely. It’s coming from the driver side so I bought an axle and I’m going to check while I’ve got it apart. I just want to see what I’m getting into here. Thanks!

Niiiice! You made a perfectly working tool and saved well over a hundred bucks. (Todays Prices: 9/25/24) And made that 3d printer more valuable and more cost effective. Ever think about marketing your design or finished product?

Damn, people need to send that shit back to China. We are building their navy and nuclear weapons by buying this stuff? Gee.

Someone has been watching Tayrl Dactyl! The Right Stuff gasket maker has been around since the mid 90;s/ I remember testing it out at a Firestone in the 1997. Back then they only had "Black" but now they have every color in the 1 minute gasket maker, Anyway, give the man some props! I'm still not sold on using a cork gasket along with RTV because The Right Stuff is designed as a gasket replacement.

I really need someone to reply to this comment. I’ve replaced the vacuum switch on the transfer case. I’ve checked all the hoses. The actuator is fine. The only thing I know that’s for sure messed up are the buttons themselves but I can get those to work enough to press them. The actuator is always fully sucked and has the cable pulled at all times yet the front wheels aren’t engaged. And when I press the buttons, all I get is a clicking in the differential and a whole lot of nothing after that. What do I do?

Will this desolve plastic cause I have a really tiny screw that has the head ripped off

I like it. A lot. How could this work on a larger item, like a Land Rover door top frame? Can't put that in a pot and heat it. Tx.

Rear 02 is controlling the fuel trim to optimize the fuel mixture. Lambda is 1 (air/fuel ratio) which is perfect.

Is there a way to remove it is the bearing is broken? Tried pulling it out but doesn’t work. The bearing is not even moving and no way i can see how to remove the bearing or the shaft. Thank you

Just bought the Max and love it but, do you notice a bit more motor whine than most with those larger 1400 watt motors? Mostly during take off? Definitely a beast of a scooter!!

Can you replace that seal without the special plastic tool that is sold with some of the seals?

I thought about filing mine too. Glad I found your video.

My lights don't come on at all. Nothing works.

None of my lights on the switch come on at all and you cant hear nothing working. i haven't got a damn clue what it is. I can't find anything that tells me how to test the switch.

Extractor is worn out

I have a 2017 Express Van 3500 a d it's got a Problem with thee headlights Flickering , can you help solve this issue.

Is that wider or same length as the stock one on the RS5? 😮

Have u managed to hit 50mph ?🛴💨 I’m upgrading my controller, display & controls . The Max controller is on its way so hopefully I can get an extra 10mph/15kph when the upgrade is complete . 🤞🏻enjoy😊

The cutting depth of the extractor channels in the OEM bolts may not be consistent, or for that matter, it may be the same with some aftermarket bolts. Great video!

So yes, I have the same trailer that I had for several years and I have the exact same trailer the 5 x 8 wire mesh and you are right they made those things as cheap as possible. but I decided to use two by eights for faster coverage. I want to put the sides on like you have yours except I think I will use treated plyboard and hopefully they have it Lowe’s I also purchased anchor tiedowns for the floor not quite sure how to install those yet and I have noticed several times using the trailer that I have either backed into an object and broke the lights off, so I have decided to do a modification and mount on the wheel wells so yeah I enjoyed your video. Gave me some pretty good pointers.

What’s going on exactly? Fuel pump leaking air into the tank?

If your running bx25 mags they are loose had to put tap on mags where they lock. It tighten them up now they fire great. And it was a brand new rugar.

Yeah, pyrex on an electric burner, not a good mix. Possibly enlist an old drip coffeemaker both for carafe and warmer. Jewelers call it pickling, to remove copper oxides.

Hi, what is the product name? Thanks

Dude you are soooo 🔥 cracking that bad boy. Just saying

my door won’t show unlocked when it’s open it’s not a big problem but the door doesn’t automatically lock it since it never detected it open

👍👍 Thanks saved me a lot of messing around

😮today i was suprised trying to fix my 4x4 but almost everything was broken for a reason but aaw your video its awesome in so many ways that i was even able to fix my colorado which was in my garage not moved for about 3 months

What is the name of that part you replaced?