Thanks for uploading nice video, what kind of water hose did you use and where to buy?
@4RibsFishing3 күн бұрын
I used 3/8 silicon hose bought online siliconehose.com. But if I did it again I'd try harder to find a roll of Yamaha hose.
@mannersdmd3 күн бұрын
@@4RibsFishing You are right, I couldn't find yamaha hose at all online, i have triple yamaha 300 outboard,, I will trying this weekend to connect them,I really appreciate your video. Any place to get yamaha hose? They are selling very short yamaha hose not the roll.
@bryanlandry129012 күн бұрын
I forgot to follow up with you following my succesful installation of the Rhodan 96. It's working like a charm and what a difference to have the capability to lock on to reefs and shut the engines off! Truly a game changer. So, thanks for the detailed videos on both the motor and electrical installation. Definitely made my life easier. On another note I was wondering if you've changed out the bungee cords on the below gunnel rod holders. I've ordered the cord online (3/16" diameter) and I guess I'll just size up the appropriate crimps once I have the cord. And advise?
@4RibsFishing12 күн бұрын
@@bryanlandry1290 I did swap them out. The factory uses 8ga electrical but splicers. Just make sure to get the tinned ones to hold up in the salt.
@powerv884413 күн бұрын
Can it be fix by cleaning it??
@4RibsFishing13 күн бұрын
It's $20. Just get a new one
@larrygaal480814 күн бұрын
we could not get a throttle blip to see how it sounds?
@4RibsFishing13 күн бұрын
I'll do you one better. GM Borla sound clips for GM 6.6 L8T Gas kzbin.info/www/bejne/ZpDKiIduqM2lipY
@AchikSarih18 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤
@AchikSarih19 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤❤
@MrTonynyc5721 күн бұрын
Very nice boat and well built. But you forgat range and price
@4RibsFishing20 күн бұрын
Yes, you are right
@AchikSarih21 күн бұрын
You are a wonderful man, my brother, May friend . Thank you very much for your outstanding work. Your human brother will benefit from it.
@AchikSarih21 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤
@AchikSarih21 күн бұрын
You are a wonderful man, my brother, May friend . Thank you very much for your outstanding work. Your human brother will benefit from it.
@4RibsFishing21 күн бұрын
Many many thanks
@AchikSarih19 күн бұрын
❤️❤️❤️❤️❤️❤️
@AchikSarih21 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤❤
@AchikSarih23 күн бұрын
My brother, thank you very much for this distinguished and righteous work that you are presenting. Thank you very much. You have presented something that you will be shown mercy for on the Day of Resurrection with a righteous deed that will admit you to Paradise by my Lord.❤❤❤❤❤❤
@4RibsFishing23 күн бұрын
Wow. Thats the best comment I've ever received!
@AchikSarih24 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤
@AchikSarih24 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤❤❤
@4RibsFishing24 күн бұрын
You are very welcome!
@AchikSarih24 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤
@4RibsFishing24 күн бұрын
You are welcome!
@AchikSarih24 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤❤
@4RibsFishing24 күн бұрын
You must be doing a lot of work to your engines!
@AchikSarih24 күн бұрын
Merci beaucoup ❤❤❤❤❤❤❤❤❤❤❤
@4RibsFishing24 күн бұрын
Thank you for watching!
@Chris_I_Fishing26 күн бұрын
New Yamaha’s?
@4RibsFishing26 күн бұрын
I was on my buddies boat. He has a newer 301cc with the newer 4.2s.
@befmx31Ай бұрын
Another great video.
@4RibsFishing24 күн бұрын
Thanks again!
@befmx3124 күн бұрын
@@4RibsFishing you're welcome.
@jhawks240Ай бұрын
Thank you. Awesome video.
@4RibsFishingАй бұрын
Glad you liked it!
@michaelcassar2897Ай бұрын
Shame on Garmin to be selling inferior transducers. My GM 20 is only 2 seasons old and my Garming 5 striker is unable to connect with the transducer. I had a Raymarine before without any problems for years until it was stolen off the boat. Garmin should do a recall and replace FOC
@4RibsFishingАй бұрын
In my case the transducer was made by Airmar. They do have a warranty, but mine was outside of that.
@JoseReneGaytanSoria-uz3tqАй бұрын
Hola hoyga una pregunta tengo un motor 250 yanaha 4 tienpos con un problema me abienta aceite porla tapa deatras del respiradero despues deacelerar de media makina sino lopaso demedia makina no meabienta kepodra cer ya lepucimos anillos nuebos y ules de culata nuebos
@4RibsFishingАй бұрын
The breather line will always have some oil vapor residue. Yours sounds excessive. I would try a compression test to see if your rings are worn.
@abtfilmАй бұрын
Awesome video! Were you experiencing symptoms or was this just for maintenance?
@4RibsFishingАй бұрын
Just maintenance. Thank you for your kind comments.
@grunner30Ай бұрын
I agree with ATR-42 Really grateful for your efforts. The part number help and all is great. I will say there is a super helpful and very simple way I've found to dispense ATF fluid. Use a piece of small tubing 1/4, 3/8, 1/2... as an artesian well kind of setup. Drill the cap with a uni-bit. Carefully drill it out to just slightly smaller than your tube. Cut at an angle on one end... makes it easier to push the tube through the cap and also allows the fluid to flow through from inside the bottle. Push the tubing all the way to the bottom of the quart bottle. Now you can simply squeeze the bottle of ATF same as Ketchup. Also, 3/16 or 7/32 drill through the top spout of a Dawn dish soap bottle and 1/4 tubing works great this way.
@4RibsFishingАй бұрын
Thank you for the kind feedback and sharing that tip. I will definitely be trying that next time.
@martin2005mvpАй бұрын
No bathroom?
@4RibsFishingАй бұрын
It has one. Unfortunately the cameraman (me) didn't check to see if the camera was recording.
@ByronHitchenson2 ай бұрын
You missed one
@4RibsFishing2 ай бұрын
Where? What one?
@nickwinn2 ай бұрын
You should ask about the 40k dollar mark up from invoice on these boats. Dealers don't do much outside of taking money out of your pocket for minimal service.
@aportilla0072 ай бұрын
Order online for cheaper internet price.
@nickwinn2 ай бұрын
@@aportilla007 Have you ever ordered a boat on the internet? I tried in 2021 and didn't have any luck. Ran into "Let me refer you to the local dealer in your area" multiple times. Local dealer didn't have those same prices or were already so backlogged on orders it would take over a year to get my boat. It shouldn't matter where I live and dealers do that to maintain their oligopoly.
@aportilla0072 ай бұрын
@@nickwinn I have not ordered a boat online - right now I own a Whaler, but will move into an Everglades in the future. 2021-2022 all builders where having issues. It might be different now. Also, you can get a better price at a boat show.
@jeffguia73712 ай бұрын
Do you know where the location of the pressure valve control.
@4RibsFishing2 ай бұрын
It's on top of the motor. Right rear. I'll be doing mine this winter too!
@jeffguia73712 ай бұрын
Would that cost a over heating problem on idle, because mine overheat in idle and when I put it in gear works fine, I did changed impeller, checked thermostat looks good.
@robcuevas74762 ай бұрын
Thanks for the video, I just built my first rod leash and will work on my second one tomorrow. Very instructional and easy to follow. Thanks for sharing your knowledge and expertise!
@4RibsFishing2 ай бұрын
You are very welcome!
@simonhaugenkolstad85612 ай бұрын
Amazing, exactly what i need. I have a strange issue that i hope could be dolved by cleaning out the vst. I have a 2011 f250d. Its mounted on a Phantom 21 Speedboat. When i take it out in larger waves and jump with it, or get alot of movement. Suddenly the engine doesnt wanna rev past somewhere between 4000rpm and 4800. Differs from everytime. It runs perfect up to that rpm then it bogs. Seems like it wont get fuel to rev past it, no warnings or anything. Then i stop the engine, pump the fuel bulb, and restart, usually that fixes it. Then it happend again next time i get alot of movement on the boat.
@4RibsFishing2 ай бұрын
@@simonhaugenkolstad8561 so your motor has two pumps. Low speed and high speed. Low speed fills the VST. High speed delivers to the motors. After you eliminate the cheap items (filters) you may need to look at how the tank gets filled. There is a float, a check valve, and a pump, one or more of these may not be performing.
@simonhaugenkolstad85612 ай бұрын
@@4RibsFishing thanks i saw this. And a pressure regualtor. So to be sure, the outside pump is filling the vst? And the innside pumo is high pressure? Or opposite. How much did the gaskets and filters cost for you? Just one of the intake gaskets is 200$ where i live... No US website delivers to Norway. Also checked the outside pump price. It was 1300$ and the inner one was 500😅
@simonhaugenkolstad85612 ай бұрын
@@4RibsFishing total for what you replaced in that video id 700$ for me
@TnFlyinGrizzly2 ай бұрын
Another excellent video! Watched this tutorial and realized I didn’t have an o-ring! Ordered what I needed and got this simple job done. If I hadn’t watched your vid the old o-ring would have went back in! Thank you so much for the great detail in your videos.
@4RibsFishing2 ай бұрын
You are very welcome!!
@TnFlyinGrizzly2 ай бұрын
Thank you for an awesome video! Just completed timing belt and t-stats on my VF250LA. Your video gave me the confidence to diy! Thank you sir!
@4RibsFishing2 ай бұрын
@@TnFlyinGrizzlyExcellent!!! Its not that hard if you take your time and have the right tools. Thank you for the kind comments.
@lbowsk2 ай бұрын
Somebody please tell me why you cannot simply just wire brush those anodes and put them back in. They show almost zero wear, only sea water crud. YAM wants stupid money for an anode. Made of quite possibly the shittiest metal on earth. Were they a buck or two a piece? SURE, toss em.
@4RibsFishing2 ай бұрын
@@lbowsk I probably could have. I did that project sooner than it needed to be done.
@KieranCox2 ай бұрын
Excellent video! Was even easier todo than shown. Just had my starboard 2023 F300 with only 260hrs shutdown and refuse to restart. Figured it was the fuel filter, watched your vid, changed it in literally less than 5 minutes and we're back up and running. Thanks
@4RibsFishing2 ай бұрын
@@KieranCox thank you. There's more F300 videos on the channel. Please subscribe!
@voodoo2u4u2 ай бұрын
What makes filter fill up and leak down half way..fill up and back down. Every 30 secs it fill to top and back down
@4RibsFishing2 ай бұрын
Your low speed pump aka take up pump fills the filter and your VST tank. Your high speed pump sends it to the motor from the VST.
@AllanGostoso-r3k2 ай бұрын
Great video, where did you find the snaps with the 8/32 ss screw (bolt). Can't find it anywhere, thanks for any info you can give. Giles
@4RibsFishing2 ай бұрын
Thank you. I bought them here: www.sailrite.com/Snap-Fastener-Machine-Screw-3-8-8-32-Nickel-Plated-Key-H
@AllanGostoso-r3k2 ай бұрын
@@4RibsFishing Thanks so much for the quick response, have ordered.
@arizadam123 ай бұрын
Well done! 🤩💯
@4RibsFishing3 ай бұрын
@@arizadam12 thank you!!
@longtabitracks3 ай бұрын
Got a Cobia as well. Same pump went out after 2 years. I’m doing this!
@4RibsFishing3 ай бұрын
Check out my video on the macerator pumps!!
@LowIQBlack3 ай бұрын
F me, the 2 strokes are a dream to service compared to these 4 strokes.
@pnw_adventures84133 ай бұрын
Awesome thank you
@4RibsFishing3 ай бұрын
You are very welcome!
@louv44373 ай бұрын
Love pursuits but the OOS models
@kbeesmot99283 ай бұрын
Is it my eyes, or does the knife need sharpening?
@4RibsFishing3 ай бұрын
Probably!!!
@baileykirkpatrick25263 ай бұрын
Does this affect the 360 view on the camera display? Do you still get the side view cameras as well? Curious to know what camera views this affects by relocating. Thank you.
@4RibsFishing3 ай бұрын
This camera only replaces the rear view mirror view. No other cameras or views are impacted.
@baileykirkpatrick25263 ай бұрын
We have a Denali so I don’t know if it is any different with the cameras. Someone said it would affect the 360 camera view because that pulls from multiples cameras and moving this rear view mirror view camera could affect that.
@bad550me3 ай бұрын
question, at how many hours is this service done
@4RibsFishing3 ай бұрын
My shop manual doesnt say - but I flush every trip and it was packed in there. Id say 500hrs.
@bad550me3 ай бұрын
excellent no music no bullshit just the facts , perfect
@Grumpyneanderthal3 ай бұрын
Well done! I’m installing a new raw water wash down system and appreciate the reverse freshwater rinse add-on.
@4RibsFishing3 ай бұрын
They just don't last long with salt water running through them.
@postulatingspin44703 ай бұрын
Looks like he changed out perfectly good anodes…..hardly consumed at all. If you flush your engine after use, I would not recommend this anode replacement…vastly far higher probability of engine damage and oil leaks. If your boat sits un flushed in salt water….different story.
@4RibsFishing3 ай бұрын
They were in good shape. With how I flush I can easily stretch the interval to 750 hours.
@TheKCaryer3 ай бұрын
WHERE would a SK 2 go?
@4RibsFishing3 ай бұрын
They put them under the helm seats. But you lose the drawers.
@markhubanks37153 ай бұрын
Great idea and video, I am using your idea. Thank You!