I’m waiting for parts to do this job myself. I have a 97 Camry with the 2.2 liter. I’m getting mixed information about the timing setup. Is this motor an “interference” engine? So if the timing belt snapped would the valves hit the pistons? Asking because my boss has one and it’s overdue for a timing belt.

Your power steering fluid is very low

Get some BG engine flush. Run it for 1/2 hour and do the directions on the can. Make sure the engine is hot when you add the BG so it goes to work immediately. The directions say for 15-20 minutes. I went 1/2 hour. My 2010 2.5 Camry was using oil before I did this. 180000 miles. I use 5W-20 in the summer and 0W-20 because I'm in Minnesota and it can get cold. Quaker State synthetic is excellent and wasn't consuming oil. If your in a southern state you could probably use 5W-20. I just put in Valvoline Restore and Protect for the hell of it and will run that 4 times for 2 years im guessing. What ever 8 can do to keep the inside cleaner I'll do. I wouldn't use conventional oil. Synthetic oil is cheap enough now days and is way better.

What type glue did you do for the foam

This help alot thanks

I hope they don’t clunk

For the price it should already be a blast ! 😊

This video was gripping from start to end; a motivation for uninitiated DIY'ers. It would have been great if setting timing marks for timing belt would have been explained in a bit more details. Great video overall and thanks for sharing your experience.

Fuse box install link?

Very good video 😊

ALWAYS remember.. SAFETY FIRST!! Never work on a vehicle with SANDLES/FLIP FLOPS!!!! always were closed toe shoes or boots!!!!

if you had a scanner capable of showing the balancing rates for each injector before and after the injector cleaning that would have been great.

Mines pouring fuel. Hoping it's not too tight. Thanks for the video

THE RF1 FILTER YOU TOOK OUT WITH MICROBIALS ALL OVER IT IS STILL BETTER THAN THE BRAND NEW FELT FILTER YOU PUT IN LOL, YOU NEED TO ADD SBG TO BOTH TANKS DIRECTLY BY THE WAY AND CHANGE THAT SSC109 SCREEN IF YOU DONT HAVE A WEBSTER PUMP. IF YOU NEED SOMETHING OTHER THAN SSC109 CHANGE THE PUMP TO A CLEAN CUT.

Please post more Lexus RX videos!

Good video man. How is the lift pump treating you? After all this time using it?

Hi MMG! please would you recommend the same oil viscosity(0W-20) for people living in Sub-Saharan regions?

here we are in september 2024 and the Lucas fluid is now $12/quart at my local store

It's NOT a 4Runner with V8. It's a Landcruiser sold overseas as a Prado Landcruiser. Jeezz... the ignorance!

use a bag

8:49 Isn't it easier to take that crusible out when you scoop the slag away? Then you won't be bothered by that heat

Do not follow his direction to change oil on the Lexus GX 460. This guy is the reason I do everything myself!!!

How the hell do you release the front end of the generator in order to remove side covers?

Did it fix the code? And did you use a torque spec to tighten? Thanks

Cool video, thank you.

Do you have relieve any air in the system after removing the fuel lines? What were your symptoms when you got the 0087?

Im almost wrapping up my used install! I’m using plywood walls. I just spent a couple hours tonight painting the deck boards

Do you know what the ID of that clear tubing you used?

Thanks for the video have the same problem on my 1997 already ordered all the parts. I think this o-ring and all the shaft seals on this side of the engine should just be done every time you do the timing belt because it's easy to get to them. The last guy who did the timing belt on my car was a monkey and left 3 bolts out of the top timing cover and it was flopping around. Safe to say he probably didn't bother changing the oil pump o-ring lol

Do I have to re learn my TCM after getting a new one?

They aren’t the same shocks anymore

Love the babys

I have a 06 5500 allison and there is no power to the tcm connector at all. Any ideas where I should look to solve this problem?

hi sir i have some problem.u0101. 0073 i changed e c m tcm bcm checked wiring some code can you give so info.i had pay few online gm tech no luck

Got a crazy question if anyone knows got a 06 lbz duramax got tow tunes but everything else is fractory low power low fuel mileage starts fine drives fine just low power can only make 11 lbs of boost at wot no boast leaks new air filter new fuel filter new fpr does loop a bit at idle when warm only factory cp3 and factory turbo truck does has 841,000 miles on it anyone have any idea what it could be no smoke and no codes

Does the Motor Overheat?

I have one of these at my local Martin’s

Fantastic video, thank you. Replace the carburetor drain line to the bottom of the plastic housing.

The pump shouldn't NEED the additional sealant, but having just gone through this, will do the same (but less than what you showed). I've found that the replacement gaskets are often smaller than the original ones and leak even when new. Further, the gaskets can dry out in the original packaging (the one I just purchased in 2024 had a date on the package from 2008!). So...additional gasket maker for me in addition to the ring rubber gasket. Last, recommend verifying that the oil leak at the pump is solved PRIOR to putting the timing belt covers (2), P/S belt, A/C belt, and crankshaft pulley on (need to install the timing belt, of course). Otherwise you will be doing all of this again if the pump still leaks after your repair. Torque for the 10mm bolts on the pump is low (76 in-lbs).

I see no Amazon link.

It'll go down in height.

fill your fuel filter with seafoam, run for 2 min, turn off and let soak for 15 min. Start and run 30 min working the motor

Good job

Curious…did it resolve the problem?…any issues with the plug?

Plus it sits where you put it unlike a jack that rolls as it lifts.

i have a 69 mustang also and i have never done a restoration. do you think you could help me with like what steps to do? i am building the motor right now and just put floor pans in it. front clip is taken off thats pretty much it. whats next you think? theres some rust holes in the body should i attack that next? thanks

How are the bees?

Awesome 🎉

Mine seems to be the tail lights. The tail light bulb receptacle looks burned. And After further inspection I found more than 5 electrical plugs and all light bulb receptacles on the outside of the truck looked burned out. Some got replaced and some just got grease. It has been a long difficult and dirty but thanks to your video, I got headed in the correct direction 🎉🎉🎉🎉🎉🎉🎉

I hate column shifter, center console shifter only suits me