Where are the setting for varget that you came up with?

Can get different sizes of pins lol

Totally love Primary Arms optics

I use BBs on the first wash before I decap. So much easier to deal with than pins.

It is NOT an octagon barrel....

Interesting about thr whole.308 vs .310 or .311 thing. Interested to see the performance

Where have you been big fella?

Like to see the measurement with primers popped out.

Vortex promotional video This scope isn't best for the money.

Great pistol. I have have the Mark IV tactical with the standard grip. It fits my hand better than the 22/45 grip. I just got the Vortex Viper red dot. Can't wait

Very nice

Yes, I even got some once fired cleaned ready to load that once I loaded a few would not cycle through any of my .308 rifles ? Once I ran them all through a resizer had no more issues.

Yes, the chamber works like a sizing die. But what if it bumps the shoulders consistently? For example - I normally size my cases to 1.627", but occasionally a 1.628 or 1.629 slips through. However, when the rifle chambers these cases, it sizes them all down to 1.627. Wouldn't it be all right to assume - if it locked, then the size is correct for that particular rifle? Just curious, I'm only starting to understand how to reload for a precision gas gun.

I drilled shallow holes in the underside of the heavier cup until they were the same weight. You have to be careful to not drill through, obviously. I didn't like the idea of tape because dirt or powder could stick to the edges and change the weight.

Thank you. This was really helpful- especially the triangular graphs on distance and amusements.

Very good and honest demonstration and review. I just got this same scope with the same reticle and planning to mount it on Remington 700 varmint in .223, thanks for your effort!

I run my Frankford for 3hours I took a 5 gal bucket blue of course, drilled four holes right in the bottom corner opposite each other, then I draped a painters nylon paint screen in the bucket an draped over the outside of the bucket, I purchased the blue strainer with holes from the tumbler folks, so now when I dump the dirty water and pins in the strainer all the pins get rinsed through the strainer leaving the brass in the top of the strainer Rinse the brass thoroughly to remove the dawn and lemi this also washes the last of the pins down into the paint strainer in the bucket. Dump the brass on a towel and Simply move the paint strainer up into the separator which drains out the water from the pins. Clean pins and clean shiny brass inside and out.

Mp7, 308 Jakyl, and bullpup Jakyl is exciting! Love psa always innovating

It works it a 22??

Just took my Ruger precision rimfire 22lr out to the range for the first time. Found out it loves CCI mini mags and Aguila super extra high velocity. Both ammos grouped under 1 MOA at 50 yards. I’m very satisfied. CCI velocitors did not group very well but they do run hot. All chrono’d slightly above the printed fps on the box. One was 1489. Rippin! Winchester segmenting silvertips did horrible, but I think it was just poor consistency in the powder charge. Had some extreme flyers. Did not try any stingers as when I slid one into the chamber it would not fit all the way inside. CCI uppercuts same story. Case too long on both. Thats why theres a warning in the manual not to use them.

I’m excited to try this out. My RPRR shoots 3/8” - 7/16” groups with Eley Contact at 50 yards. I’m interested to see how this improves after the bedding, and properly torquing everything down.

So lemi shine just has some citric acid in it? Would a little bit of vinegar (acetic acid) do just as well?

I just bought the supplies to build this, and the link to the power supply was one I used several times. but what I received was an Arris adapter, right volts and amps, but would not fit into the power socket.

So strikefire 2 or Romeo 5? Looking to sight in around 50+ yards

What were the speed (high an low) with which you configured the vibrator?

Found this channel searching for load dev data on a Tikka 20" T3X CTR, and must say the content, just like this annealer build tutorial is "A Grade". Thanks, so appreciated

3.6” is pretty close

1 mrad @ 100yds is approximately 3.5984”

I purchased the Sig Romeo5 and Juliet X3 Micro Magnifier from PSA and did not care for either (Red Dot looked feathered and the Magnifier had terrible eye relief) so I returned them and purchased Holosun HS510C & HM3X Combo, cost a little more but well worth the upgrade.

Nice stuff 👍 I wonder if they are going to make an upgrade for the AR-V 9MM 🤞 I've got to return the one I have " jammed constantly"🤦

I’ve watched a handful of videos trying to figure out if I wanted a Mil scope or not. Coming from a military background all I’ve used is MOA. This is hands down the best in depth video I’ve seen. Great job on the explanation.

Excellent video mate, cheers from Western Australia

Thanks

Or... you could put a shell holder in the jaws and you can lower the platform exactly where you need it.

Dealing with the pins is not that big of an issue for me!

That AR was grouping pretty good at 300 yds lol

Prototype was much better looking. Seems like a big mistake. When the production gun debut I was like meh 🫤

Nailed it!

Did you chrono the AKP or just pull generic data off the web?

The american long range shooters would be much better off, if they just learned the metric sizes. It must be much easier to do the math in metrics, and then have the understanding of what the result roughly equals in imperial units. Like 4 inches equals 10cm, 50cm equals 20 inches. 100 yards equal 91meter, or 100m equals 109 yards. That way it's easy to take advantage of the simplicity of the metric system...

I am super glad you put the link at the end of the video for this video this allows me to continue

Have viper,venom, eagle nothing but good anybody can get bad optic I would send it back calling it junk whatever great customer service

I already have an A3 TRIAD chassis coming....did they mention if the new barrel was going to be available in 300BLK? If there was an upper kit with the 1pc barrel in stainless steel and around 13.9" like the current upper A3 offers then I am all in. How do you host a suppressor with no adjustable gas block?

Light right up to your rectum? LOL...I have both 3x15 and 5x25. They are really nice glass. I'm not sure what calibers they can handle.

4 pm 30th My brass is not the right size after reloading. Is it because i'm not analyting the brass

My loads are not passing the kerplunk test, they are 1/16-1/8 above flush. Not all but many. When shooting I get jams that won’t cycle the next round. What should I be doing to fix this?

From d philippines great stuff

From d philippines

Nice bro easily understood great info so far💯

You getting them way too hot. They should drop right at the dullest glow.