Hell of a video, thanks man.

I've been back here a few times. Thanks again for the video. (Was also nice to hear the lady getting involved :) )

Nice!!

Amazingly detailed video and writeup! Question, where can I get the service manual for my 25hp 1998 Mariner? Thanks again, 🤙

Are you still sailing?

Nice informal mast stepping video.. You covered many of the little and subtle details. I have and O'Day 19. Always raised the mast from the stern. And I always wondered why O'Day chose a deck plate with two pins, rather than one like on my Capri 22. Never thought about raising the mast from the front. With my O'Day 19, I can easily heft the mast up. But on my Capri, I use a somewhat similar bridle arrangement and use the wicker pole as the gin pole rather than the boom as you did. My goal was to have everything I needed to step/unstep the mast stored in the boat. Too bad you don't have a trailer tongue extender so your vehicle doesn't need to go into the water. My Capri trailer has an extension easy enough to extent/retract so my wheels don't even need to get wet. Again, nice informal mast raising video.

An EXTREMELY THOROUGH video! Thanks so much man you really helped me!

Hey buddy. I have 99 15 hp mariner. It burps when manually pushing throttle on the carb. But when manually pushing the lever with the idle wire. It runs awesome. Any ideas

What body of water is this? Thanks for the informative video. The narration often got too soft and I missed a lot of the commentary.

A veteran Mercury outboard mechanic told me this- When you seat the new impeller into the cup, add a little grease into the cup and the impeller fins will find the correct direction upon start up.

Hola me podría alludar que número lleva de chicler

Yamaha shift shaft disconnects in the middle to make it easier.

Hahaha mikey!! Haha

That was a great mini production.We went in sept.,no crowds. We stayed in.r.v. at east koa..,its a relaxing simple little town.Half hr north in pocatello is pizza pie cafe buffet for cheap, five pastas, various pizzas,salad bar about 10 bucks.Your steaks beat that .tnxs for the production.

This vid was extremely useful, ive just followed it doing my 2001 Mariner 15 "stroke service & impeller etc. Really appreciate your help

very well done

Awesome video, true gem of tutorials! Following it frame-by-frame working on my 9.9 Merc. Special thanks for the list of supplies, made it so easy to get all those things!

It's blue

Freeze them first in the freezer. Then freeze drie them. It will take less time.

Love that you are both excited and enjoying this together

I passed my learners permit test today!! 92%, I’m all kinds of proud, this video helped me figure out what to do prior.

Great video!

Well done video!!! Thank you very much for your time invested!

im 2 years late on this video. We just got our Harvest right and i am trying to learn cycle times. Your video says they were in for 39 hours. How long was the freeze cycle and how long was the dry cycle?

Nice video! Do you need 4-wheel drive car or high clearance car to arrive the trailhead?

This guys should NOT be giving tutorials, so many rookie errors ...

Best video. Does this have a thermostat, or only in bigger engines?

ı am from Turkey meen thank you for thıs

This was one of the most detailed videos ever used. You did a excellent job. Thanks for the video and details. 👍

No fucks given about your neighbours 🤣

Very helpful thank you!!

Ethan took the test three days before my bus was hit by an Ethan, which gave me a concussion and tons of problems. How strange.

Great video! I need to replace the bushing between the tiller handle and the motor. Do you have a clip of that or did I miss it?

Thermostat seems to not open all the way. Weak pisser.

Do you need to put it into fw gear before you pull the lower?

Bleach lol. No

What are you running for fuel? I was hoping you had a link, i use tru fuel in my yard tools. That stuff is about $20 for almost a gallon. Thanks Mike

Excellent Excellent video. Thank you so much!!

Very helpful!

Best father-son chemistry!

No you have a sailing boat

Do these motors have a trim tab to control steering?

I have the exact same boat. Based on the O'Day mast raising instructions, those delta attachments were an optional accessory. Wish mine came with them. Once you get everything rigged, you could help the lifting by using a mast crutch at the bow end.

Thank you for taking time to post this! Very helpful!

Thanks for this video , I already changed the oil on my 2 stroke mercury 15 hp .. I would like to change the water pump on my motor, would you please share the link on the pump kit I need for mine too? I searched for it in Amazon but I get allot of options so I don’t know which one to buy . So I’m just gonna go with your same kit . Thank you for the video and the link to buy mine.

We have this very engine and are so appreciative of the effort you put into this. You instilled in us the confidence that we can do the maintenance ourselves….fingers crossed! Kudos for keeping it simple and providing all the supporting notes.

Awesome video thanks for taking the time to make it ✌

Camera was getting some hard looks at that hot spring.

Thanks for the instructional video... very clear detailed instructions. I'm picking up my very first (used) boat in a week with a 1999 40HP 2stroke Merc and I imagine it's going to be a pretty similar job, so was great to see you do it first. One question (and I realise this vid's now 2 years old and you've probably already fixed it)... your engine seems to be missing the trim tab anode from just above the propellor... does this model not have one?

As soon as you said bleach, I stopped watching and started writing this review. I can still hear your video with good information in the background as I write, BUT!!! I am sure there are many like me who know aluminum and bleach are not friends. I suggest you edit your video with info reviewers provide as well as the great info you already have. High 5's to Liz Ramirez.