Helpful video. I managed to update my maps but am worried that updating the firmware will cause faults as I also don't have OBD tool. What type of OBD scanning tool did you use?
@SiakaDiakite6 күн бұрын
thanks so much
@petedakin1410 күн бұрын
Very nice video, great job. Just about to do similar on my Polo 9N :)
@javitobosch8 күн бұрын
Thanks! Reach out if you need any tip =)
@mattwarriormx599913 күн бұрын
How long does the update take? I have a bad battery
@javitobosch8 күн бұрын
Hi! I think this specific update took no more than 15 minutes. However, I would recommend you to place a good battery first or use an external power source to power the car. No one wants to deal with a jammed infotainment system. Good luck!
@sergeika.255117 күн бұрын
Cool video.
@mgwalker7717 күн бұрын
Interesting video, thanks. Was going to update the firmware (currently exact same version you updated) but I don't have an OBDeleven system so wouldn't be able to clear the fault 🤔
@javitobosch8 күн бұрын
Hey! No worries. The fault came back. There is nothing wrong with that, except that the system labels the update as "suspicious" because it cannot verify it officially somehow. car runs perfectly and infotainment too. Good luck if you finally decided to proceed!
@mgwalker778 күн бұрын
@@javitobosch useful to know, thanks again 👍🏻
@t7ank23 күн бұрын
We need someone to patch those HW50 (SW train 05xxT) units, so greenscreen toolbox would work. Even single video with emmc reading would be good. Or at least USB2HSD cable method, but with detailed steps how to do it.
@javitobosch23 күн бұрын
Really nice one! I will take a not and start working on this one as soon as I have time =)
@Steven-zp8hf24 күн бұрын
How did you release those tabs exactly???
@javitobosch23 күн бұрын
Hi! Stiff screwdriver with a flat tip (I prefer the ones that are meant to be for electronics). Your best friend here, a mirror that allows you to see the tabs. So, insert the screwdriver and feel the tab, pry and part of the airbag unit should come out. The other half should be a bit more hesitant due to the added tension, but nothing to worry. I realize now that I did not fill the process and I should do this more often. Noted! let me know if I can help you further =)
@boastyyАй бұрын
Nice job mate, it came out better than new!😀
@mkwanja3Ай бұрын
Did you replace the exhaust silencer?
@javitoboschАй бұрын
Hello! I replaced the entire exhaust line. This is catalytic converter, id silencer and end silencer. The last two were second hand =)
@josephmcconnell4654Ай бұрын
I watched this video several times and I can’t figure out from the original BT board what color wires would be the D+ and D-, can you help me with this?
@javitoboschАй бұрын
Hi! Is the diagram shown in 26:58 not helping you? Is the cable coloring different?
@josephmcconnell4654Ай бұрын
@@javitobosch The wires on mine are in a different order. D6-black, R15-gray, D3-white, D4-purple, D2-red
@javitoboschАй бұрын
@@josephmcconnell4654 sorry for the late reply. Work is hectic at the moment! OK, D6 and R15 are not used in the new board, correct? Then D+ will be your D3-white, D- will be your D4-purple and final 3V3 will be your D2-red. You can also download the schematics of your board and do a mapping =). Please let me know if I helped you correctly. Good luck!
@josephmcconnell465427 күн бұрын
@@javitobosch Yes, that was very helpful, but I actually found an adapter that I can plug the connector for the Bluetooth directly into, so I won’t need to do any soldering
@javitobosch23 күн бұрын
@@josephmcconnell4654 Oh, that is amazing! Do you possibly have the link to the adapter. I would like to take a look too =). Glad I helped you and best of luck!
@slonkijippieАй бұрын
Cool video. Maybe you can make a video of some cool custom things you can do? Maybe change the startup-background or any other cool tweaks that you know? :)
@javitoboschАй бұрын
Hi! Yes, that is a nice one! And I think you can do such things BUT you need something like OBDEleven, Carly, VCDS or similar. Y Took a note and for sure I will come back to this! Thanks a lot for your suggestion!
@MrBobbya5Ай бұрын
Hello, the file is not there anymore...any other solution?
@javitoboschАй бұрын
Hi! Which file? The webpage still works, correct? Can you be more specific? Thanks!
@marcindudzinski6232Ай бұрын
There was some update on mibsolutions page and unfortunately now only 1 old version (0253T) is avaliable for SEAT_ZR.. There are no other files in that folder.
@ElgonntАй бұрын
What about External amplifier (Bose, Bang&Olufsen) might need dataset after update firmware? Do you have any trouble with sound , if you have bang olufsen sound system??
@javitoboschАй бұрын
No trouble with sound so far but you are correct, specific datasets for these amplifiers might be needed in some cases.
@ElgonntАй бұрын
@@javitobosch thanks for answer. Any idea how to get them/correctly install them?
@DankoFedak2 ай бұрын
Hi I crack the mirror glass and bought new one, but new mirror doesnt have theese 2 pins for conectors. Do you know what they are there for ? 2:12
@javitobosch2 ай бұрын
Hello! I believe it is for the heater functionality. Something useful in countries where winters are really cold =)
@alexbalanescu62652 ай бұрын
the link for the firmware update isnt working anymore, it says that is an "Argo Tunnel Error". I've send the link to others friends to see if it works for them, but it doesn't. If you could help me guys i will appreciate that :)
@javitobosch2 ай бұрын
Hi! Thanks for the heads up! I guess not it works? 😃
@alexbalanescu62652 ай бұрын
@@javitobosch i see that now is working again :D
@alexbalanescu62652 ай бұрын
@@javitobosch Yeah, the page fully works, but the issue that i have is that my station has the MHI2_ER_SEG11_P3315 version, and now i found on the page that is another version MHI2_ER_SEG11_P4704_MU1308.7z. I dont know if it is the correct one, but is the only one wich is available as i can see... I downloaded it on an USB, connected to the car and it dont allow me to update the firmware. I think the car dont read nothing on the USB. (The USB wich i used is an new Kingston, i just used it only for this oporation).
@ElgonntАй бұрын
@@alexbalanescu6265 not working again, invalid username
@javitoboschАй бұрын
@@alexbalanescu6265 I think @fritz3039 already mentioned that changing from 3XXX to 4XXX is not possible, always within 3XXX or 4XXX. I must say I did not know about this issue.
@nemanjaja78112 ай бұрын
Can you help, after radio update I'm missing all radio station logos, non of them I can't find even if I hold the icon like you did on video...
@javitobosch2 ай бұрын
Hello! I remember I did not have any radio station logo at all since I purchased my car and my dad with a 2015 Seat Leon had all of them. Quite annoying. I would suggest you to update the Radio Data Base (RDB). All steps are in the video =). Let me know if it helps
@nemanjaja78112 ай бұрын
Exactly after rdb update I missing all logo's, before update I had it all
@javitobosch2 ай бұрын
@@nemanjaja7811 Did you try to remove all stations and re-add them one-by-one?
@nemanjaja78112 ай бұрын
@@javitobosch well after update like you did in video, I turned on radio, and there is no logo on any of stations, I tried everything and didn't manage to get it back, even inspected folders that I downloaded and there is also no any logo inside. After all, I downloaded just pictures from some of radio station and do it manually, but still no success with automatic logo picture...
@fakie_shots_61582 ай бұрын
I have only 8 colours for the ambient light in the doors. I spoke to some people and they said I need to update bcm you thin this will do it?
@javitobosch2 ай бұрын
Hey! What does "bcm" stands for? Honestly, I know that it can be done via OBDEleven. I remember adding quite a big range of colors.
@fakie_shots_61582 ай бұрын
@@javitobosch yes I did with obd but the colors then don’t show up my system needs an update I think
@javitobosch2 ай бұрын
@@fakie_shots_6158 That is really strange. Have you tried a hard reset of your unit?
@daspec2 ай бұрын
- Wears gloves to handle electronics - Leaves the GPU on a tower with static electricity 🤦😂
@javitobosch2 ай бұрын
Hi! Good remarks! Long time ago, though. And no worries, everything is under control. I can see I feel confident in the video! This war horse is still rocking like the first day! 😜
@cfos1182 ай бұрын
Hi there, what thermal grease/paste did you use for the graphics card?
@javitobosch2 ай бұрын
Hi! Good catch. I thought it was in the video haha! If I remember well, back then I used Arctic Silver 5. I think there are better options out there and also for similar cost. Hope it helps and thanks for reaching out!
@FireWillWorkNL3 ай бұрын
Moet het met een SD-kaart? of kan het ook met een USB?
@javitobosch3 ай бұрын
Hoi! USB kan ook, maar dat heb ik nog nooit geprobeerd. Heel veel success met the upgrade!
@IdharUdharKiBaatain3 ай бұрын
On my Seat Arona, the Apple Car Play once showed up, and then disappeared again. Do you think it can be solved by firmware update or I should try to get official help ? The possible reasons of Apple Car play showing up could be that I visited Czech Republic for a day , while I live in Germany. For now, I have to use just Android Auto because Car Play does not appear.
@javitobosch3 ай бұрын
Hey! This is a really interesting case, to be honest. Android Auto working but CarPlay not. As fas as I understand they all come within the same software package. A way to proceed that I have in mind for you is to press the menu button for a few seconds (like in the video) and once in the Service Mode, click on the Function enabling Codes. There you should see the Apple Car Play/Mirror Link/Android Auto package and should also tell about status (something like Valid/Not valid/Not accepted). If SWaP, FEC code is OK, then verify that your iPhone has CarPlay enabled (Siri must be enabled for that). And if these to are OK, then I would ultimately take the car to the dealer for further diagnosis. Good luck and let us know what the outcome is! You might be helping someone else in the future!
@IdharUdharKiBaatain3 ай бұрын
@@javitobosch Hi, I saw another video about VW where he told to factory reset, so I found the option to factory reset Full Link and now it works. In his case it was App-connect, in my case I had to factory reset Full Link
@javitobosch3 ай бұрын
@@IdharUdharKiBaatain Thanks a lot for sharing and good that you solved the issue!
@fritz30393 ай бұрын
I'm not able to Update from 369 to 479... what am I doing wrong?
@javitobosch3 ай бұрын
Hello again! Can you provide me with a bit more information? What kind of message does the unit display? Why's is it not able to update? Are you looking for the right firmware?
@fritz30393 ай бұрын
@@javitobosch I updated with the Firmware from mibsolution from MST2_EU_SE_ZR_P0359T to MST2_EU_SE_ZR_P0369T and now I want to Update to 479. But my display always shows dependencies of update not met. But its the right Update for my car... dont know why it worked with 369 but not wuth 479
@javitobosch3 ай бұрын
@@fritz3039 sorry for the late reply. I have no idea to be honest. Do you possibly know if the new firmware ends in T (e.g., 479T)?
@fritz30393 ай бұрын
@@javitobosch nope, 369T. But in the meantime I have the answer... its not possible to do an official upgrade from 3XX to 4XX or 5XX...
@javitobosch3 ай бұрын
@@fritz3039 I was not aware of that. I actually just checked my car and you are right. It came form the factory with 514T (now 516T). The question that I have is why upgrading is not possible if you literally have the same HW as mine? Thanks for sharing!
@fritz30393 ай бұрын
Did you patch MIB System?
@javitobosch3 ай бұрын
Hey Fritz! Thanks for reaching out! My unit is not patched. It is 100% original from factory.
@ppppppp1463 ай бұрын
Hi, what kind of sd card are you using? ( mag ook in het nederlands)
@javitobosch3 ай бұрын
Hooi! Thanks for reaching me! I believe a U3 type card is what I have (±30MB/s) with 32GB capacity just in case. Veel succes met de update =)
@ppppppp1463 ай бұрын
@@javitobosch dankje! Komt vast goed met de mooie uitleg! Lekker bezig💪🏻
@javitobosch3 ай бұрын
Hoi allemaal! A new version of this video is uploaded and it also includes the update of the Point of Interest, Speed Cameras and the Radio Database! You may have access via the following link: kzbin.info/www/bejne/oam2kI2chL-JiZo
@bassiejnl3 ай бұрын
My unit seemd to update the firmware correct. But after the second reboot. The unit is stuck on the Seat bootscreen for over 40 minits. Do you know how to recover this?
@javitobosch3 ай бұрын
Hello! Have you tried to press the on/off button for good 40 seconds (hard reset)?
@nikospodochoritis43323 ай бұрын
My Leon Cupra 5F 2019 model has the software MST2_EU_SE_ZR_P0515T installed. I found there is 516T version available in the archives. How do I update it? Also does anybody have any idea why android auto wireless adapters do not work with my cars full link?
@javitobosch3 ай бұрын
Hi! Thanks for reaching me and apologies for the delay! New update video is live: kzbin.info/www/bejne/oam2kI2chL-JiZo. And as of the second question, I have no clue unfortunately. Let's hope someone in the comments or in a forum can help you. Good luck!
@BP-sf7br4 ай бұрын
so well explained in detail
@MattP-oz6ps4 ай бұрын
I'm actually surprised that China has not made a membrane clone with an attached ribbon cable for the Apple Magic keyboard.
@javitobosch4 ай бұрын
😆 Good one. I think they are so badly designed that even the Chines cannot find profit on making one of those haha!
@johnboy24364 ай бұрын
spark plugs on the ea888.3 are 25nm. not 30nm.
@javitobosch4 ай бұрын
Hey! Thanks a lot for the remark. However, what I can read in the workshop manual is 30Nm for DNUC engines (and many others). You may find this information in Chapter 28 - Ignition System, page 579 (link to Workshop Manual in the video description). Hope this helps!
@johnboy24364 ай бұрын
@@javitoboschI checked over and over on the internet. All i can see is 25nm. Im sure it will be fine!
@bm_wuratli6883Ай бұрын
@@johnboy2436 its depend spark u bought* oem spark is 25nm u right
@erwinvanriel58434 ай бұрын
What was wrong with the pcv valve?
@javitobosch4 ай бұрын
Hi! Absolutely nothing. Preventive maintenance it is =). I know it is recommended to replace this part every 50000km but I believe that the dirtier it gets, the more oil vapors that will be entering the intake manifold and the more carbon build up will happen at the intake runners. Replacing this valve more frequently does not solve the problem, but will delay it. I chose to do this every ±20000km.
@bm_wuratli6883Ай бұрын
nothing wrong but put ur lil hands too pcv valve in lil hole if doing suck inside u need to change*
Via welke website kan ik de meest recente firmware voor mijn Seat Ibiza FR uit 2018 downloaden? De link om de omschrijving van de video werkt niet (meer). Alvast bedankt.
@javitobosch4 ай бұрын
Hoi @djannick95! Ik heb net de link gecontroleerd en deze is een beetje traag, maar het werkt =). U kunt ook de volgende link raadplegen: mib-helper.com. Success!
@jerryx20004 ай бұрын
Did the new PCV valve make a difference?
@javitobosch4 ай бұрын
Hi! Honestly, I replaced it because of preventive maintenance. Did I feel any difference in response? No. Did I see any difference when cleaning the intake manifold and runners? Yes. Less carbon buildup. But, I must say this depends on the driver too =). I hope my answer helps you
@geraldpheonix5 ай бұрын
My iMac 2010 shut down randomly after changing PSU
@javitobosch2 ай бұрын
Hello! Can you please provide a bit more information? For example: is the replaced PSU the same model as before? Original or replica? Thanks!
@geraldpheonix2 ай бұрын
Yes, later found out it was the GPU, but now it requires a pram reset often with a k1100m Even after flashing the card
@javitobosch2 ай бұрын
@@geraldpheonix And did you also install Open Core? If so, is the graphics card compatible with your iMac? You can check it here: forums.macrumors.com/threads/2011-imac-graphics-card-upgrade.1596614/?post=17425857#post-17425857
@geraldpheonix2 ай бұрын
@@javitobosch I think I need to try bios mod with nikey22 instead of Nicky
@AKJ199505 ай бұрын
thanks a lot for sharing you experience I appreciate it. -i have 0514 and i have apple car play and android auto working perfectly, do you think upgrading is worth it? I have to say the screen sometimes act crazy but not sure id the software is the reason -Also i see in the link u have posted you have 516t is it fine to upgrade from my 514 right away to 516t? thanks in advance!!
@javitobosch5 ай бұрын
Hey! I am super happy that you found this video useful! First of all, I believe the changes between 514 and 516 are minor. We as users are not really able to notice the difference. I must say that from 479 to 5xx my unit suffers from less freezing events (I had to restart the whole unit every time). Perhaps we are talking about the same issue? I think if version 514 works so well as you mentioned in your car, just leave it as is. On a separate note, I just installed 516 (video soon!) and it works as well as 515. I could see that there were minimal upgrades in CPU.main files (maybe for efficiency?). Anyway, keep me posted if you have any issue =)
@AKJ199505 ай бұрын
@@javitobosch mine acts jumpy if im zooming in and out for example in the maps, that is why im not sure if the software would solve this issue as it seems like the touch capacitor in these cars are a bit old. Total freeze happens every 3 weeks or so. I think ill give the update a shot, but do u know if there is anyway of backing it up if everything goes south? looking forward to your video update 🙌🏻 thanks again, cheers from Leiden!
@AKJ199505 ай бұрын
quick update:did the update and it took like 15-20 mins, as u said i did not notice any difference. Thanks man you are a genius!! -on another note though: i updated also the navigation, it works perfectly but what i find weird is that after the update it doesnt start with 6p0 anymore it starts with V0 even though i nade sure i fownload the 6p0. cheers man!!
@javitobosch5 ай бұрын
@@AKJ19950 Thanks for keeping me in the loop! I was about to record the last part of the video and you got me curious. Indeed, the new maps update starts with V0 and I have no idea why (I also made sure that it was the right one). The thing is, it works! Thanks for letting me know and greetings from Boxtel!
@dikketwigt6 ай бұрын
Why did you change the oil pump?
@javitobosch6 ай бұрын
Hey @dikketwigt. Good question! The oil around the oil pan failed, so I had to replace it. While doing this job I thought it might actually be a good idea to replace the oil pump as a preventive action, knowing that it was the original one and that the car had more than 146,000km. The pump itself showed a bit of wear on the gears, but nothing unusual. It just gives me peace of mind!
@therealspixycat2 күн бұрын
Did you experience low oil pressure alarms? I do and have to do the same to figure out the root cause
@adamtrokich86056 ай бұрын
I dont think upgrading the pan for tempeture is any idea. Bigger oilcooler and maybe pressure flash? The best benefit is durability and reusability. That original tap screw man, horrible.
@javitobosch5 ай бұрын
Hi! Well, I like seeing that the oil pan is able to cool dow the oil and keep it under 120Cdeg in summer. Th drawback comes during winter, when the oil really struggles to reach 80Cdeg and above. I just drive more carefully. I am not really thinking about an oil cooler as the car has an oil cooler. Small but enough I believe. And I agree with you: plastic oil pan is really not my preferred choice, and that plastic screw...oh man!
@hammadrehman35077 ай бұрын
Hello - Did you notice consumption of more oil and some idling issues before you upgraded this part?
@javitobosch6 ай бұрын
Hey! Apologies for the late reply. I did not notice any of what you mentioned. I did this job as part of preventive maintenance, since the PCV valve is full of diaphragms that are prone to fail due to wear or clogging.
@stefanleblanc11557 ай бұрын
Hallo Javito, Zeer veel dank voor het delen van dit filmpje, ik kreeg de update maar niet in orde maar met jouw hulp rij ik nu opnieuw met de meest geüpdatet versie, zeer veel dank en waardering voor je moeite!
@javitobosch5 ай бұрын
Bedankt voor jouw reactie Stefan! Groetjes!
@dangerousdeo51137 ай бұрын
AWESOME VIDEO AS ALWAYS! Had to subscribe! I am looking at doing a K3100M upgrade to my iMac 27 inch as the GPU does bad, stops it from booting up Linux. Which is what I use on it. The only thing I do not know is does the card work with the 2010 version of the Mac 27 inch! :)
@javitobosch5 ай бұрын
Hey! thanks a lot for your comment. You made my day! Maybe you can check that information in Open Core Legacy Patcher: dortania.github.io/OpenCore-Legacy-Patcher/ ? Just saying. Good luck!
@dangerousdeo51135 ай бұрын
@@javitobosch Glad to hear dude, honestly thank you for going through with the topic. Super excited to be doing this, my plans are to get a new GPU sorted in April! :)
@terrygee2107 ай бұрын
My old 1.0 MPI 6N2 has just passed its MOT. It is one of the very few with a working electric open air roof. It uses almost no oil and will still happily cruise at 70MPH (110 KPH) on long journeys.
@javitobosch5 ай бұрын
It is a war horse...tiny little machine that take you anywhere...with time =)
@noplayboy18 ай бұрын
After hours of trying, your advice with the overall.dns file was the key. Thx a lot from Germany. Btw tarraco 2019
@chennahichem67908 ай бұрын
من فضلك اريد تحديث سيارتي والسبب يكمن في عدم اشتغال الشاشة الثانية امام السائق الشاشة الرئيسة
@philpots32169 ай бұрын
Oil filter is mann too.
@pove_79 ай бұрын
BIG THANKS for the big tip on 08'55" beacuse if not, it doesn't work! 🙌
@jihadbenouttas37029 ай бұрын
Thank you for your sharing and support, i have ateca 2023 , i am in Morocco, i cannot connect wireless carplay , and i noticed wifi grey ‘not activated ‘ please support