Very good video! I am thinking of buying this kit for a motor-home. I also wonder about those two thin yellow and green cables. Could it be that they function as a comparator? Let me explain: the control system sets a voltage between 0 and 5 volts, where 0 will be the minimum temperature attainable and 5 will be the maximum temperature. Then a temperature sensor placed at the blower inlet will translate between 0 and 5 volts as well. If we set 2.5 volts on the digital control, for example, when the sensor reaches half of its scale, that is, 2.5 volts, after translating from temperature to voltage it will begin to lower the RPM of the compressor until the temperature begins to rise slightly. In this way, energy efficiency is achieved and the desired temperature is maintained stable. Aside from those accessories, of course you should have the compressor temperature sensor for protection, as you mentioned, also the pressure switch, to control the high and low pressure, especially the high pressure, but also the low pressure, in case there is a likeo, the compressor stops, to avoid breakage due to lack of lubrication. Thank you very much for your video. Greetings from Tampa, Florida. Muy buen video!. EStoy pensando en comprarme ese kit para un motor-home. Tambien me pregunto por esos dos cables fino amarillo y verde. Pudiera ser que funsionen como un comparador. Me explico: el sistema de control fija un voltaje entre 0 y 5 volt, donde 0 será la mínima temperatura alcanzable y 5 será la máxima temperatura. Entonces un sensor de temperatura puesto en la entrada del del blower se traducirá entre 0 y 5 volt tambien. Si fijamos 2.5 volts en el control digital, por poner un ejemplo, cuando el sensor llegue a la mitad de su escala, o sea 2.5 volt, despues de traducir de temperatura a voltaje comenzara a bajar las RPM del compresor hasta que la temperatura comience a subir ligeramente. Así de esa forma se logra eficiencia energética y mantiene estable la temperatura deseada. Aparte de esos accesorios, por supuesto debería tener el sensor de temperatura del compresor para su protección, como has mencionado, tambien el presostato, para controlar la presión de alta y baja, sobre todo la de alta presión, pero de baja tambien, por si existiera un likeo, se detenga el compresor, para evitar rotura por falta de lubricación. Muchas gracias por su video. Saludos desde Tampa, Florida.
@JackButlerVideosАй бұрын
These videos are great, thanks! Would love to see an update video
@kannanpd4541Ай бұрын
Hai shop were
@RJGPGАй бұрын
My oem low pressure setup breaks ground, i assume i couldnjust wire the same as your second page but use a relay between closed side of low pressure switch to ground a 4 pin relay and pull 12v to green wire on inverter?
@VWJosephАй бұрын
Thank you! I just got a kit from China and wasn't 100% sure on the wiring due to that yellow wire.
@juanitobiker57572 ай бұрын
Donde se conectan los dos cables que salen del compresor los que están forrados de blanco
@nickmcdaniel6102 ай бұрын
Would love to pay you for some assistance with triggering mine 😅. Let me know
@budiharyanto40862 ай бұрын
how much is the compressor price
@labtekvenezuela2 ай бұрын
saludos amigo teddy, compre uno de esos directamente desde china, el mio es un poco diferente pero sigo con dudas respecto a la conexion especificamente en los dos ultimos terminales de arriba hacia abajo, en su caso es verde y amarillo, en mi caso es verde y negro, segun un pequeño diagrama que me envio el proveedor el cable verde es "TX fault feedback line"y el negro es "9v-19v signal line 1 square green" asi tal cual esta escrito, puedo entender que quizas el cable negro señal 9 a 19v es el cable de señal que sale de un sensor de presion de 3 pines, pero el cable TX color verde no lo termino de entender, si usted pudo solucionar y me puede ayudar le estare muy agradecido, mi auto es viejo no hay ECM que controle el sistema A/C, asi que lo conectare de manera clasica con el boton en el tablero y un termostato analogico como el que se usa en los sistemas domesticos de aire acondicionado, pero me falta informacion para estar claro en lo que hare, tengo compresor, evaporador, valvula de expansion, lineas, filtro, sensor de pesion todo esta totalmente nuevo, en mi pais no hace tanto calor y mi auto es pequeño puede resultar bien, pero no quiero quemar nada! estare muy agradecido cualquier ayuda de su parte!
Just might heat up your intake temperatures a little bit 12 volt source for the AC should be at the AC's relay
@nickmcdaniel6102 ай бұрын
Care to provide any assistance with wiring for my conversion 🥲🤣
@cpylant12262 ай бұрын
If you rotate those clamps 180° opposed for each other they will sell a little bit better
@cpylant12262 ай бұрын
Seal a little bit better
@cpylant12262 ай бұрын
Is that diode absolutely necessary or have to be there it's the factory AC compressor clutch switch has a diode too
@cpylant12262 ай бұрын
I'm pretty sure that they eliminated the circuit to you so you could use your factory pressure switch it's what I'm trying to do let me know if you have any hope with that I think you just need to disconnect or cut the wire to one of the pressure switches probably the high side and connect those wires to the left and the right terminal of the pressure switch so that way whenever the fan gets to those pressures only problem is some of these switches don't come on unless you have pressure so you have to install the whole system
@mahmoodjani13712 ай бұрын
Sir who much pres only compreser and kit tell me sir
@Driftprodigy013 ай бұрын
How is the system does it cool good i currently have a weekend car that doesnt have ac because my exhaust runs through the same location front facing headers and dont have ac compressor room
@felipefarfan23803 ай бұрын
a question. I have the same compressor and my question is the cables that come out from inside the compressor, where do they connect? thank you very much for your video.
@DailyUseofSuzukiKatana3 ай бұрын
There is the video result ? How cold in cabin?
@jonavtech3 ай бұрын
What kind of Compressor Oil are you using?
@bannablitz2472 ай бұрын
I think these are required to use a specific oil, ester or mineral maybe? one is conductive and kills these compressors so be careful.
@abosaraabosara75443 ай бұрын
اسباب توقف الكمبريسر في الاجواء الحارة هل هو خلل في الكهرباء ام في الضاغط
@mikekimble60843 ай бұрын
Like that lip smackin
@TheChromeCollective4 ай бұрын
How do you connect this so it doesn’t constantly draw power from the battery when the keys are out? I’ve wired mine up to the battery but the green light is always blinking which I assume would draw the power of the battery down over time if the car sits for a while
@TeddyZues4 ай бұрын
That is a status monitor, Thats the LED that will give you all of your fault codes and the yellow wire is there so you can r mount an indicator light somewhere remotely, Mine has been in my jeep for a year or so and has not given me any issues. It will shut off after a timed cycle.
@JimN_AustinTx4 ай бұрын
First impressions is it’s underpowered at 12V. Physics can’t be overcome as you will be pulling lots of amps. IMHO - Really needs 72v to provide enough cooling for most vehicles.
@rommelekstrom19734 ай бұрын
Wher i can order elictric ac car compressor
@jonathanhermis19294 ай бұрын
I have one of these in my 55 plymouth.. Its only going to cool around 20 degrees cooler than your ambient temp.. These are mostly designed for RV's or truckers... It will maintain cooling for an already cooled room... I wasted lots of money on my unit to get it running as an alternate solution to drilling into the block and fabricating stuff for an ac system in my plymouth.. I made a rear mount trunk system with a custom evaporator and pusher fans to suck air from the evap through package tray vents.. Its loud.. I have 4 100ah lithium phosphate batteries running my system and it will stay running for about 4 hours.. My condensor is mounted on the bottom of the car with a fan.. How much freon is a mystery as the readings are never what they are supposed to be.. I have 48 ounces of r-134a in mine and the high side is still not where its supposed to be... I tried it also with 24 ounces of freon and the high side was very very low along with the low side.. Again only going to cool 20 degrees lower than the ambient temp... The green wire from mine is ran from the controller through my pressure switch to the evap... So when the evap is turned on it sends 12-13 volts through the pressure switch to that trigger input initially turning on the compressor.. The speed changes are useless it seems to only work at one speed.. There is supposed to be a controller module you can purchase that has a screen and settings. It is showing this in my book perhaps this is how you get it to run cooler.. I have yet to see a video on start to finish on these.
@jonathanhermis19294 ай бұрын
I have two of these systems... My green wire is ran from the controller through the pressure switch to the trigger wire from my evaporator... That yellow wire does nothing.... The ones I have purchased have a safety link from the controller to the compressor.. Some have these and some don't... However I can tell you from using these its only going to put out 20 degrees difference from ambient temp.. If its 100 degrees Fahrenheit outside the best it will put out is 80 degrees.. And how much freon you put into these compressors is a mystery.. I have 3 12 ounce cans in mine and low side is around 60PSI and High Side around 140PSI... I try to follow the standard chart for R-134a and its never correct... Maybe someone can tell me how to get these systems to cool better.
@AutoMotoMechanic3 ай бұрын
Try it around 35lbs on low side. Keep great air flow across condensor
@AutoMotoMechanic3 ай бұрын
If you're plumbed right back in factory condesor and evaporator etc then the refrigerant capacity should be roughly the same
@UNITEDUNIONOFALLWORKER4 ай бұрын
Can I run this compressor from solar panel on car roof
@ramonpena84484 ай бұрын
It would depend on your panels/ batteries output. This compressor I believe pulls about 65 amps @ 12v dc
@kernj64544 ай бұрын
Does it get cold as a belt driven one ?????????????????
@TeddyZues4 ай бұрын
nope.
@kernj64544 ай бұрын
@@TeddyZues a belt driven is a 10,where does the electrical foll in a scale of 1 too 10 ?????????????
@donaldperry1485 ай бұрын
So this compressor is universal and be connected to any condenser and evaporator
@sshyshy60976 ай бұрын
did you ever find it out?
@TeddyZues6 ай бұрын
Yes I am just starting to use the system again and it is working well. I will be making a final video on this shortly. I am running a 160AMP alternator out of a 2001 5.9L Dodge Durango, I have upgraded the charging cable from 6AWG to 2AWG as well as the cable running to the second battery which is out of a 2001 Ford Explorer. There is a 250AMP diode between the 2 batteries and a battery isolator to prevent overcharging and alternator damage. With this set up I have been able to run the system continuously without damage for a month now. The last step is to get some hoses made because mine are leaking, go figure.
@vivek.ananth6 ай бұрын
I’m looking to do this, was it possible on your end?
@marf_61246 ай бұрын
If you are still looking for an answer, you dont really need that yellow wire. Mine internal unit came with the control panel and stuff that I didnt need, so I just replaced it with the simple thermostat with the temp probe which has to be only connected to the +12/24 and green one as it is now. Works perfectly. I had made my own diagram for this 😂
@marf_61246 ай бұрын
Okay, I just saw the second video, so nvm. Great job on this!
@rmgcustoms46677 ай бұрын
compressor has any oil in "stock"? or i shoud fill it?
@chrisfreeman81757 ай бұрын
Where did you buy the thing to power the compressor
@TheJrmojo7 ай бұрын
Hi you have any follow up mate?
@TeddyZues7 ай бұрын
Yeah I am working on a follow up now that I have found a suitable alternator and beefed up the electrical system to support this devise and other add ons.
@zelikmedina79838 ай бұрын
Yellow wire for the pressure switch?
@juniorrosa018 ай бұрын
Does it take oil or just straight 134
@yarielrodriguez22949 ай бұрын
Español
@IDKWTFID10 ай бұрын
Hey brother do you have messenger or somewhere i can contact you to pick your brain about this setup
@RaymondSymons10 ай бұрын
I have one almost like yours how much ester oil do you add and I only have the block where the smaller wires are on the compressor and the large you have going to your power block are on the compressor and I got no instructions with this kit and no response from the company
@bobtomica961410 ай бұрын
How much current draw? Did you upgrade the alternator? and additional battery?
@TeddyZues10 ай бұрын
I do already run a house battery and I have yet to upgrade the alternator. There are a few packaging issues I have to address before I do said upgrade but I'm looking at an alternator out of a 2007 Cadillac Escalade, Those things are listed at 260 amps from factory so it should get a long life but its huge and $$$. My amp clamp was having a hard time getting an accurate reading but its peak was 92 amps.
@ricardolevy8859 ай бұрын
you serious 92 amps?? thats eleven hundred watts!!!
@overbuiltautomotive12993 ай бұрын
@@ricardolevy885 uh yep the factory belt drive car ac system are even more but via the engine of course
@bobtomica961410 ай бұрын
How much current draw for the whole system?
@roguevapers434110 ай бұрын
So glad I found this video and info, I’ve been looking for weeks for info on this compressor. I’ve got mine setup with a new under dash system from old air manufacturing. I’m assuming the trigger wire to turn the compressor on is the green wire? I’m using the condenser fan controls and hi/low switches built into the under dash unit and not the ones on the compressor module. Do you know if this will work, only hooking up the (green) trigger wire on the comp. Sorry so many question but I can find any info on this unit. Tia
@bobtomica961410 ай бұрын
Did you upgrade your alternator and built a dual battery system?
@AMAZINGWORLD-pi5fi11 ай бұрын
I'm from oman I want your help I have JCB backhoe loader I want use electric compressor I want to know if I use then battery no go low?
@Kreegers_performance11 ай бұрын
What size AC fittings?
@TeddyZues11 ай бұрын
the kit did not specify, I would say its a 6 and an 8 (10mm - 12mm) or 3/8'' - 1/2''