Beautiful truck , I have a 1969 ford f250 manual. Need be done same work thank for the video
@phoenixarizona844117 күн бұрын
Jag z 440 is the first model of the zr440
@gabefrmdak18 күн бұрын
thank you . I’m 18 and i’m not the best in mechanic stuff but this was very useful and i did it all by myself ! if i can do it anyone can .
@rbljackson28 күн бұрын
ive got a 98 ram 1500 same engine that's been sitting for 4 years. I tried to get her running and it cranks but no start. I can hear the fuel pump kick on for the initial cycle and have 45 PSI fuel pressure. When you were getting the crank but no start, did you notice if your tach gage moved at all while cranking? Mine isnt so my initial thought was crank position sensor. I also hooked it up to a scanner and im getting two codes: one for the Crankshaft position sensor and a second for the Camshaft position Sensor. Seems odd they would both be bad at the same time?? Any suggestions?
@manuelortiz640729 күн бұрын
Thank you so much for the video help me to do my water pum
@jameswilsin5348Ай бұрын
If you pull all that with radiator in put piece cardboard between radiator and fan or engine so you don’t damage it
@jameswilsin5348Ай бұрын
If you pull all that with radiator in put piece cardboard between radiator and fan or engine so you don’t damage it
@jameswilsin5348Ай бұрын
If you pull all that with radiator in put piece cardboard between radiator and fan or engine so you don’t damage it
@jameswilsin5348Ай бұрын
Get the pull pulled kit at harber freight it has everything for power stearing to other pullys and only cost around 30 bucks
@jameswilsin5348Ай бұрын
With this heat wave I’m putting a cooler on to got replace my pump so cooler to make it last longer in the excess heat
@jameswilsin5348Ай бұрын
I’m retired mechanic with 40 years experience on those I allways took hole air conditioning bracket of and fan blade assembly makes it faster getting apart but I still watch those cause some times you pic up ideas that makes it faster don changed my gear box witch was a pain they allways are on a 4x4
@jameswilsin5348Ай бұрын
I use a transfer pump then put back in same way never have bleed the air out cause there ant no air no mess no cleanup
@georgegouvas27Ай бұрын
why wear a hat indoors
@chinoreyna448Ай бұрын
😲 hope that ain’t a customer’s car.
@brandontyler175415 күн бұрын
It's not anybody's car. It's a truck not a car.
@chinoreyna44815 күн бұрын
@@brandontyler1754ok , well hope that isn’t a customer Truck.
@buickpower1972Ай бұрын
did you do a rear suspension install cant find the video?
@hamms5560Ай бұрын
Great video. Let’s see some more Ranger 500 videos!
@McCarminerАй бұрын
I like that you are involving your son in the repair process; teaching him about tools, and how to use them, and safety, and 'letting him' do some of the work. A great way for a father and son to bond...the little guy will remember this long after you are gone. Nice job parenting.
@kevinhogan7152 ай бұрын
I did mine about five years ago on my 2001 ram . What a fu@king nightmare. If you take the two body mounts, bolts out on the right side, and jack the right side of the body, you can slide your hand up in there. The other thing is long, Allen Wrench shaft and Universal knuckles. And a lot of swearing in beer.
@Poopydraws12 ай бұрын
Do you think a predator 212cc would fit in the spree?
@josephbuckley36192 ай бұрын
Not like mine but thanks for the air siphon trick! I like that !!
@josephbuckley36192 ай бұрын
Your air conditioner and alternator are on opposite sides than mine,.?!?
@robinpedler12392 ай бұрын
thanks for the vid i have a 610 with a 1200 nissan engine going to repower with 3cyl kubota especially how to drive the hyd pump Cheers from Australia
@paulhare6622 ай бұрын
I just finished a Mazda 323 GTX tank. It sat for 10 years with a quarter tank of gas in it. Having tried muriatic acid years ago with poor success I went with white vinegar, 5% cleaning vinegar. Four gallons of vinegar and filled/ diluted with tap water. Sealed the tank and let it set full of liquid for 8 days rotating it daily. Drained and hosed out the loose gunk and refilled with two pounds of baking soda and water, left to set 4 hours then drained and rinsed. Dried in the sun and sprayed inside with a full can of WD40. No solvents were used, the varnish came off with the rust with no sticky residue was left over. Just an FYI on what worked for me.
@arthurchacon8864Ай бұрын
That sounds great too. Thanks
@Uncletoast522 ай бұрын
Mine had the inline six with the granny four speed but, NOT ANY MORE !!
@Johnny-vu7db2 ай бұрын
Pro Tip: Check your push rods while you're at it. I had a plugged one. A week after doing the valve seals it started ticking again because oil wasn't being pushed up through the hollow push rod.
@josecastrejon4142 ай бұрын
Did he forget about one of the coolant lines I only saw him reconnect 2 of the 3 that go on the pump
@user-od7ym3df5m2 ай бұрын
Can't you drain the radiator by simply removing the bottom hose?
@southancomfortkennels67142 ай бұрын
Thank you
@smokeydabeecharlescoleman83653 ай бұрын
Bought it, and sold it back to him ? WTF!!! This is your dad!!! You buy it and over pay, then you fix it and give it back!!!! That is what I did for my son !!!
@OpaM-so3tw3 ай бұрын
Thanks, having trouble removing power steering pump, saw the bolt but now need a puller. Thanks again.
@coyoteserranoband3 ай бұрын
Stupid question here; are both jets supposed to work at the same time? For a 2 bbl? Or is one a idle jet and the other a main jet.
@shadowrockcairns83903 ай бұрын
Did great informative I stall !! Looks good Thanks😊
@georgewatson9633 ай бұрын
Loved using gear lube jug with hose to fill carb bowl
@johnbarrow92383 ай бұрын
Do you have a video on the v8 swap?
@Jbone27373 ай бұрын
Thank you, my friend, but show me how to do it🦾🙏🏽
@CamoPajamies4 ай бұрын
My god the face at @6:51 is a meme. I know what’s wrong with it, ain’t got no gas. God bless you, keep living the dream with a true purpose ☮️❤️♾️brother. I saw a lion leading his pride with good balance when I saw your video.
@KelsaysShenanigans4 ай бұрын
Hey, Excellent video keep them coming. Enjoy your content.
@preacher0311634 ай бұрын
Another failed disc jockey!!! If i wanted a music video thats what i would be watching!!
@cassondrabarquet97044 ай бұрын
Your details literally helped change mines 😂😂😂 🎉🎉🎉it’s literally saved me money ❤❤❤
@markpeterson95464 ай бұрын
Thats a pretty ambitious swap, I'll give you alot of credit on this one. I have a 610 myself and have been all over it, just recently redid the drive pully speed mechanism, sleeved the bore and made a new piston, works fine now. My background is welding, fabrication and machining.
@raymanning10644 ай бұрын
Just a tip.. be more interesting to show less of your face and more of the work you doing. Just don't take it wrong. Thx
@Ninjaconn134 ай бұрын
Do you have a link for the 14 peace kit..?
@southernprojectsyt63404 ай бұрын
a/c pump ? a/c compresser .................. learn what things are before you make a video over lack of education.................
@byker4lyfe15 ай бұрын
Hey bud there is an easier way to do this that ensures the valve doesn't fall down I. The bore... takes a bit longer but way safer. Run about a 3 foot length of old spark plug wire in the sp hole whilst the engine is at TDC bang no worries mate
@bkyardmechanic50105 ай бұрын
Great video, pretty smart u are. Lot of thinking going on :)
@bubbawatson18525 ай бұрын
Any idea on where I can find one of those 5 bolts type, Mine has 3 outlets on top. Need help finding a solution.
@deanscherer6875 ай бұрын
You could also have a 351 v6
@paulinebenjamin6135 ай бұрын
Very helpful video. Besides your own knowledge, how did you know how to take everything off for that specific engine?
@SkittlezZ825 ай бұрын
Awesome video man, I just pulled the carb off my panther deluxe this afternoon and cleaned it up still wont idle nice even after she’s warmed up. Got some more fiddling to do I guess! Cheers!
@ryanstadel31755 ай бұрын
My question is this. Where did you find the ubolt with the 1/2 drive insert😢 i could really use one of those