Run Volvo electric ps pump, put the pump in the bed.
@classicstangbrn896411 сағат бұрын
No Explorer 8.8, run the rear on top of the springs so you don't have to use the crap kit?
@satyavratadas164011 күн бұрын
What rear end setup are you running?
@scmotorsports11 күн бұрын
I have a 91-92 Ranger 8.8 rear end with 3.73 gears in it. I might switch to 3.55 or 3.27 gears in the future though. We'll see.
@flyinhawaiian917411 күн бұрын
I used to run between 12.2 & 12.8 with my '91 Mustang GT. I had upgraded heads, 1.6 roller rockers, Ford B-302 cam, 3.55 gears, shorty headers, Flowmasters and a short throw shifter & Centerforce clutch. I had about 325 HP at the flywheel. Car weighed around 3000 lbs. It was built more as a street car as it also had sub-frame connectors. Car had zero body roll in the twisties. Fun times. My 1/4 times vastly improved once I learned how to power shift.
@randumadventures12 күн бұрын
This what I been waiting for since I found your channel!
@randumadventuresАй бұрын
I love that textured ABS plastic sheets. I made the whole face of my rangers dash and console with that stuff
@donkeytime1704Ай бұрын
Impressive power potential the modern 5.0's have, just wish they didn't sound like European v8's.
@2dorkstvАй бұрын
I have been following a while. Super impressed by how thorough you are on these videos and how well you think things out. I'm not good at that, so I just live vicariously through you :D. Great work!
@scmotorsportsАй бұрын
Haha. I try to show my thought process. Not saying my thought process is correct every time, but maybe it helps someone figure out the right way. Thanks for watching!
@flyinhawaiian9174Ай бұрын
Installed one in my '02 Ranger a couple of years ago. Came with Android Auto. Easy install, but needed to fabricate a bezel as the stereo wasn't solidly in there without it. Best upgrade on my Ranger for sure.
@terryburton971Ай бұрын
What year ranger
@scmotorsportsАй бұрын
1989
@terryburton971Ай бұрын
@@scmotorsports love it my friend
@terryburton971Ай бұрын
What
@jeremypike91532 ай бұрын
You've routed your pcv hoses backwards. The passenger side goes to the vacuum source behind the throttle body and the drivers side goes to the plenum tube between the air filter and the throttle body. What you are hearing is air sucking in past the rear crank seal. When you pull vacuum on the fresh air side of the pcv system instead of the vacuum side it closes the pcv valve which operates like a simple check valve and the crank case cannot get fresh air unless it pulls it from a seal somewhere. Apparently the easiest seal to pull air past was the rear main crank seal. Reverse the two pcv hoses and the problem will stop. However you may have created an oil leak somewhere else as well.
@obbyjep75972 ай бұрын
It might be leaking vacuum around a seal
@mikekosar61352 ай бұрын
Cracked line..Squeeking
@logicalguy4882 ай бұрын
Bad PCV valve causing high vacuum and it's sucking on the main seal.
@deadcarz49262 ай бұрын
Donvict's voice, then MTG's, are far worse.
@mikeburke68282 ай бұрын
The reason why it sounds like that is because it's a Ford ! ! 😂😂😂😢😂😂😂...
@Heyitsme1222 ай бұрын
It’s a trick question. The coyote itself is the most annoying sound in the world
@scmotorsports2 ай бұрын
When I wrote the video title, I figured someone would make this comment. It's all good, haha!
@danielmyers53832 ай бұрын
I had the lines from my valve covers wrong and got the same noise. One of my valve covers has a restrictor on one side. Its probably pulling air around the rear main seal.
@renasilvestri65252 ай бұрын
Did a dual inlet catch can run both valve cover ports to the catch can use one vacuum source from the intake manifold plug off the other vacuum source
@scmotorsports2 ай бұрын
That might just be an option for me. It would look cleaner than having 2 cans in the engine bay. Thanks for the Tip.
@BengSilver2 ай бұрын
Interesting. I knew you would figure it out and will come up with something nice to replace the line. 👍
@muffgames2 ай бұрын
It’s a ford
@SMB-1022 ай бұрын
So?
@flyinhawaiian91742 ай бұрын
Since the whine went away when you replaced the vent tube with a filter it'd be my guess that the whine was caused by the vent tube being clogged. You might try a vent tube with a built-in filter, but the vent filter is good enough.
@sergiomartinez36732 ай бұрын
What type of front bumper is that on your ford ranger? It doesn't look stock
@scmotorsports2 ай бұрын
That is the stock steel Bumper that came with the truck.
@makingmustangsgreatagain3 ай бұрын
Ford fucking RANGER 🐎🔧🚗👊💪🇺🇸
@Novoa2003 ай бұрын
I love the vid man, I love what you did. I'm planning on doing somewhat the same thing how much did you spend on the engine and what tips would you recommend?
@scmotorsports3 ай бұрын
Sorry for the late reply but I was on vacation. Yes, you absolutely have to keep you eyes open for a good deal on the engine. You are going to see anything between $2000-$10000 for a new or used engine. As far as tips, it depends on what direction you want to go with the truck.
@brad53163 ай бұрын
I love this video!! Can't wait for future videos!
@scmotorsports3 ай бұрын
I have the 10 part episodes of the build up on my page if you want to binge. Thanks for watching.
@flyinhawaiian91744 ай бұрын
Throwing parts at a problem is always so costly. I don't know how much knowledge the mechanic you're working with actually has, but someone who maintains equipment is a far cry from someone who can diagnose exactly what the problem might be. Learn from your own mistakes and pay attention to detail!
@SKRILLAMAN444 ай бұрын
Whatb about Spintechs?
@SINISTER.COLLECTION4 ай бұрын
Eventually gonna do this to my 99 ranger, awesome build walk through vids and awesome to see it
@cbcb29604 ай бұрын
I dropping a 347 in my 85 ranger but im trying to figure out what radiator to go with
@scmotorsports4 ай бұрын
The V6 Radiator may be enough to cool the V8 depending on the fan you put on it and it should bolt up. I used a factory 91 Fox Body Radiator originally when the 302 was in it, but I had to modify the radiator support and frame rails for it to fit. Good luck with the 347.
@big30534 ай бұрын
I have 03 ranger with 2.3 Will rear work with mines
@scmotorsports4 ай бұрын
I need a little more info to answer that. 93 Rangers and newer have wider rear axles than 92 and older. About an inch wider on each side. They might physically bolt up, but are slightly different. What axle are you trying to put in your 03?
@big30534 ай бұрын
@@scmotorsports ist 2003 Ford ranger with 2.3 motor single pickup two seater no extra cab
@scmotorsports4 ай бұрын
@@big3053 You asked if the "rear would work for yours". Does your 03 Ranger have a 7.5 rear end or a 8.8 rear end in it from the factory? And what rear end are you wanting to put in your truck? I installed a 91-92 Ranger 8.8 rear end in my 89, it's a direct fit. If you tried putting that in an '03, it would be 2" narrower. The leaf spring pads could be in different spots and the outside axle bearings are different sizes on some, so be aware. Here are some great links for all the info: www.therangerstation.com/tech/ford-ranger-rear-axles/ www.therangerstation.com/tech/ford-7-5-inch-rear-axle-history-specs/ www.therangerstation.com/tech/ford-8-8-inch-rear-axle-history-and-specs/
@alpha13dylan5 ай бұрын
The flow fx is literally a glass pack muffler.
@truraza5 ай бұрын
That's NICE! The 4 wheel flat dollies from Harbor Freight would be good if you make a base for those pipes once collapsed. They have two sizes.
@drcornelius82755 ай бұрын
I thought about this but ended up making some panels that I attach to hooks on the ceiling when I need to paint. I also thought about running a track around the ceiling and buying one of those heavy plastic curtains to pull around when needed. Your idea works great for your space, well done!
@scmotorsports5 ай бұрын
If i wasn't worried about getting overspray on the ceiling, I would have done the curtain track. That would have saved a lot of money and I could bunch up the curtain over in the corner. Also, i wasn't sure how to get the curtain track past the garage door.
@Bigmitch_20015 ай бұрын
I have a temp paint booth, not collapsible but I can break it down and put it back together. My issue with it is the overspray sticks to the plastic, I have the heavy duty stuff, so I take a water bucket and a wet cloth and wipe the overspray from the inside walls. IDK how the thinner plastic would work with that, but the overspray sticking to the plastic is a thing... trust me! I like the collapsible booth thought, I may try it in my garage, mine is in the basement right now.
@scmotorsports5 ай бұрын
One of my reasons for going with thinner plastic is I figured once it gets full of paint, it will be easier and cheaper to replace. Thanks for watching.
@gordbrooks14295 ай бұрын
Awesome video! I am looking into doing something similar, I plan on installing a non explosive fan tho not sure what your spraying just a thought, don't want to go boom. Thanks for sharing, great design
@warrenpeterson60655 ай бұрын
These kinds of purpose built projects are always fun to do. You could reduce the wobble by inserting square cut wood (cut from 2x4's) the full length of each upright. Of course that adds weight, effort, and cost. I think I would have simply bought 2 each 12'x12' cheap pop-up canopies with walls from Walmart ... placed end to end ... zip-tied them together ... and thrown plastic drop cloths over the join. Cheers Bud.
@scmotorsports5 ай бұрын
Yeah, I thought about the pop up canopies too. I've seen how people use those and they work pretty good. I didn't see any that would fit my application. Almost all of them have a peak on the roof which would hit my ceiling or I would have to lower it but then it might not be tall enough for what I'm painting. I also wanted to make sure the booth was as high as possible but low enough to be able to open the garage door too. I guess it all depends on the space you have to work with and what you intend to use it for. Thanks for watching.
@Turboblazer946 ай бұрын
One thing I can think of is your pipe diameter. 3 inch is more mellow and less raspy than a 2.5" also for as quiet as your looking for a straight through muffler like most of the ones you tried are not going to work. I have a chambered flowmaster on my 5.3 swapped blazer and it's nice sounding at idle and normal driving. But once you get spirited with the pedal it gets louder.
@scmotorsports6 ай бұрын
Going with a 3" exhaust did cross my mind. I figured if the Mustang comes factory with 2.5", that would work for me. Plus 2.5" is good size for that HP level. The Magnaflow XL's i originally had on the truck are Chambered mufflers and when I tried them, they were slightly louder than the Flowmaster Flow FX. Trial and Error I guess. :) Thanks for watching.
@dakotamedlin486 ай бұрын
How hard was the swap? I plan to do a similar swap for a baja ranger
@scmotorsports6 ай бұрын
I have a 10 part series on the build of this truck if you want to watch how I did it. The biggest part of the job was replacing the front suspension and building custom headers. If you have a 93 Ranger and newer, I don't think you will have to touch the suspension, because it is IFS. Mine is an 89 with the Twin I-Beam. The steering box gets in the way of the alternator. Space is limited everywhere but I got it to fit. Good luck with your swap.
@monibo70756 ай бұрын
Sweet ride
@SavageNasty2536 ай бұрын
spintech 6000 series or the 9000xl series are said to sound similarly and I got some for my benz but have yet to install. cherrybomb vortec sounded good on my 04 silverado 4.8. Hooker aero chamber sounded alright on my 350tbi 2door tahoe. I ended up getting an 09 silverado and put blackwidow 250 and are pretty decent sounding for my 4.8l. All dual mufflers. I wanted to have it idle nice and mellow but have a nice loud roar when I floored them. All x pipes except 09 with Borla SwitchFire Resonator Delete X-Pipe for a mustang (it fit like a glove). I looked at some gibson MWA there are two versions but those go in the loud direction but do sound really, distinct. I'd get away from the flowmasters. that's such an old-man-90's thing now. same with hooker but, the aerochamber is a fun design. If you enjoyed the xpipe more than the hpipe, check out the above models. They all kind of have similar designs in mind and I think you'll see what I'm talking about. thank you for the video. I don't even like fords but it's fun anyways.
@scmotorsports6 ай бұрын
That's a lot of mufflers for me to check out. :) I appreciate the info. Once I recover from this round of testing, I may have to revisit it down the road. Thanks for watching.
@SavageNasty2536 ай бұрын
@@scmotorsportsyeah man of course! keep putting out quality content!
@tomasmoreno30386 ай бұрын
Try the FLOWMONSTER straight through oval mufflers they are inexpensive and really quieted my car down significantly give them a try good luck and make a video
@scmotorsports6 ай бұрын
Thanks for the info. I will look into that.
@tomasmoreno30386 ай бұрын
@@scmotorsports I forgot to mention they are made by Holley same company that makes Flowmaster but at half the cost
@BengSilver6 ай бұрын
You may need to add a J pipe / quarter wave resonater to solve the problem to solve the drone at certain rpm
@jeremystanley96696 ай бұрын
small block 302 flowmaster 100%
@nolan5.026 ай бұрын
Nice truck. I personally like the Borla S type great sounding not load in the can very clean! Also of you piped out all the way back its going to sound cleaner
@flyinhawaiian91746 ай бұрын
Sound is totally subjective. Had Flowmaster American Thunder on a Mustang and a Bronco in the 90s. Had the same on an 07 Mustang. Currently have a Magnaflow on an 03 Ranger with the FlexFuel 3.0. Planning a 302 swap, supercharged with Flowmasters. I think Flowmaster sounds the best overall and definitely sounded best on your truck.
@michaeltexmjs64206 ай бұрын
Question? Where did you connect the Ford Red/Green 12V switched wire from the coil and C110 plug? You mentioned in the video to run it to the kick panel side to a wire, is the wire the same Red/Green wire at the kick panel?
@scmotorsports6 ай бұрын
If I remember, that wire gets powered from the Ignition switch on the steering column. Then supplies switched 12V (while cranking) to the coil, distributor, and ECM power relay in the Passenger side kick panel. I left the wire going to the passenger side kick panel there as a good spare power supply. The Red/Green wire should run from that 4 way connection by the brake booster all the way over to the kick panel. I hope that helps.
@monibo70756 ай бұрын
Why not vacuum lines for the catch can ( of course oil resistant grade)
@scmotorsports6 ай бұрын
I'm thinking you mean Rubber vacuum lines? I was trying to find lines that looked like factory PCV lines, nothing too bulky like rubber hose. I liked the look of plastic lines over the rubber ones. I even tried "reshaping" some factory lines with not a lot of success, so I settled on the swing pipe that I used.