Set the center height to the spindle first. Then used a height gauge to set the offset for the radius
@user-ll9lh4qy5fАй бұрын
@@stovepipe666 все это хорошо ! но если нужно уложится 0.05 мм на диаметр как быть ?
@stovepipe666Ай бұрын
@@user-ll9lh4qy5fthere’s also a digital readout on this machine you could also use gauge blocks if you need that amount of precision to set the radius.
@swanvalleymachineshopАй бұрын
Lol , just a wee bit of wear ! Cheers 👍
@stovepipe666Ай бұрын
Too much grease max 😂
@swanvalleymachineshopАй бұрын
Nice one 👍
@stovepipe666Ай бұрын
Thanks max
@workingovertime4429Ай бұрын
Another good video thanks
@stovepipe666Ай бұрын
Cheers
@olan6600Ай бұрын
Nice piece
@stovepipe666Ай бұрын
Thanks
@CraigLYoungАй бұрын
Thanks for sharing 👍
@TrPrecisionMachiningАй бұрын
very good job stovepipe
@derekblake93852 ай бұрын
Glad to see you still posting, am following along 👌
@stovepipe6662 ай бұрын
Thanks progress is slow on it
@manfromthemist19582 ай бұрын
well done that's a very nie job there.
@stovepipe6662 ай бұрын
Cheers thanks
@TrPrecisionMachining2 ай бұрын
very good job stovepie
@swanvalleymachineshop2 ай бұрын
Great job . 👍👍👍
@stovepipe6662 ай бұрын
Another job off the list
@CraigLYoung2 ай бұрын
Thanks for sharing 👍
@seanodoherty26792 ай бұрын
Tasty job 👍
@stovepipe6662 ай бұрын
Thanks
@mickocallaghan48962 ай бұрын
epic stuff
@stovepipe6662 ай бұрын
Cheers mick
@paweisyn74463 ай бұрын
@andyg33 ай бұрын
ive been looking through some photos from your build of this. looking at the axle tube, did you bore the ID all the way through, and just machine a small recess for a top hat bearing, instead of like on the drawings where you bore out the length of the bearing
@stovepipe6663 ай бұрын
looking at them earlier i machined a step on the axel tube and made a top hat bush to suit far as i can remember the bore was big enough to pass the axel through the center of the tube, are you after starting building one
@andyg33 ай бұрын
@@stovepipe666 I have started already, currently machining the axle tube, bore it next. Impossible to get castings now though, this is from a pattern someone else made and isn't very accurate, my bore will have to be a lot bigger
@stovepipe6663 ай бұрын
@@andyg3 have you much done where are you based
@andyg33 ай бұрын
@@stovepipe666 nothing much at the moment. -all plate work laser cut. -horn plates and spec plates drilled. -2nd shaft bearings part machined -axle tube part machined. -got cylinder and trunk castings, crank bearing castings. - boiler due in april the idea is to do it as a roller, ive drawn all the roller bits up, but we shall see. im in surrey,
@stovepipe6663 ай бұрын
@@andyg3 be something different as a roller are you casting the back wheels or built up ones if you want any pictures etc let me know there’s a few errors on the drawings ti watch out for too
@joserubielrodriguez4293 ай бұрын
Ustedes hacen el trabajo, me envía número de teléfono me hace el favor
@tourmetallathes3 ай бұрын
Good job 🎉
@Gryksza213 ай бұрын
Hello, is this machine BF63, do you have any documentation for it?
@stovepipe6663 ай бұрын
It’s an 80
@shawngoldsberry7474 ай бұрын
Nice
@TechnicalLadle4 ай бұрын
Thanks 👍
@FrogandFlangeVideo5 ай бұрын
Very cool.
@stovepipe6665 ай бұрын
Thanks
@MidEngineering5 ай бұрын
Surprised you got away with climb milling with that radius cutter.
@stovepipe6665 ай бұрын
Yes worked out fine
@christophb.67205 ай бұрын
Ah - I thought smoke-box door first but everything looks s omuch bigger in your place ;)
@stovepipe6665 ай бұрын
Yes Chris super size everything on the 3”😅
@alanbrown44465 ай бұрын
A lot of fine work going into that brake assembly. Pleasure to see someone taking the time to make perfect parts.
@stovepipe6665 ай бұрын
Takes a bit of time with all the setups. Probably could have fabricated it too
@TrPrecisionMachining5 ай бұрын
Very good job my friend Stovepipe
@stovepipe6665 ай бұрын
Thanks 👍
@hmw-ms3tx5 ай бұрын
Hello Stovepipe. I like your spindle support. Did you make that yourself or did it come with the machine? I may copy yours as my HBM didn't come with one. Do you know what kind of clearance you have between the bronze bushing and the spindle? Have a happy new year. Thanks, Ken
@stovepipe6665 ай бұрын
Hi that machine is sold now it had a nice sliding fit over the spindle not too tight made a big difference to reduce chatter it was a casting and most of the material inside on the back was hollow which kept it lightweight happy new year to ye all
@christophb.67205 ай бұрын
nice rubber job - dide mine at BH leake too - very nice chaps there ...
@stovepipe6665 ай бұрын
Easy to deal with too
@user-zp4jr5we2w5 ай бұрын
I not understand price shipping put us Dallas
@user-zp4jr5we2w5 ай бұрын
Price & shipping to Zambia
@user-zp4jr5we2w5 ай бұрын
Price for this tractor how much
@TrPrecisionMachining5 ай бұрын
goog job stovepipe
@RustyInventions-wz6ir5 ай бұрын
Very nice work. Merry Christmas
@CraigLYoung5 ай бұрын
Thanks for sharing 👍 and Merry Christmas to you and your family 😅
@realtechknowledge5 ай бұрын
Best content
@Javid-bc3mc6 ай бұрын
Where is your located
@swanvalleymachineshop6 ай бұрын
Looking really good . There are some mega hours gone into that project . Cheers 👍👍👍
@stovepipe6665 ай бұрын
cheers max yes id say up around 1500 hours now, lot to go yet! shop work gets in the way
@swanvalleymachineshop6 ай бұрын
Great bit of fabrication & machining there . 👍👍👍
@christophb.67206 ай бұрын
Hi Fergal, always great fun to watch all these familiar parts in an extra-ordinary scale :) I think the shaft for the brake needs a bit more play in the bracket as it is following a curved movement of the lever at the bottom ?
@stovepipe6665 ай бұрын
hi chris yes that bracket has a bit of play to allow for movement, the parts get a lot bigger and heavier
@Bhati116 ай бұрын
Making threads on lathe ❤❤❤❤❤❤
@Bhati116 ай бұрын
Wao too good work for you ❤❤❤❤❤❤❤❤❤❤❤ I like it keep up again ❤❤❤❤❤❤ I am watchung from pakistan pakistan
@user-wd1ol7gz3t6 ай бұрын
No bluffing there man only brilliant maching
@stovepipe6665 ай бұрын
bluffing all the ways some day i might get it right
@user-wd1ol7gz3t5 ай бұрын
Don't believe that making good chips all the time man
@steam_fan6 ай бұрын
Top job as always
@stovepipe6665 ай бұрын
cheers
@marksimpson74936 ай бұрын
Awesome job looking forward to seeing this one in the flesh!