2 жыл бұрын
4 жыл бұрын
6 жыл бұрын
6 жыл бұрын
6 жыл бұрын
Пікірлер
@robertovomende7758 7 ай бұрын
I Love my coyote s4
@Captndarty 7 ай бұрын
Nice looking kit. How would heated seat elements do with the silk film?
@RANSDesignsInc 7 ай бұрын
I asked the supplier and he said that heat from a heat gun wrinkles the plastic a bit but does not burn it, so he thinks it would be ok, you'd have to do a test to be certain.
@eddieberry8450 7 ай бұрын
Great step by step instructions and narratives, Eddie.
@portnuefflyer 10 ай бұрын
Well worth doing, a great upgrade from the older smaller tanks, as it increases the utility of the plane a LOT. Not that hard, did mine a few years back, not as scary as it would seem!
@LTVoyager 10 ай бұрын
It takes a brave man to use a fly hole cutter in a hand drill. I was using one today in my drill press and even that makes me nervous.
@bingus3573 Жыл бұрын
Yo nice shirt who made that?
@bfryar22 Жыл бұрын
Crud! Wish I knew this before last Saturday! Work smarter not harder!
@CLEAREDDIRECT Жыл бұрын
Awe man. Nice job! Wish I did this on mine
@ericlarson2336 Жыл бұрын
I've got the skins already riveted. Is there anything I have to be concerned about if I try this by working in the wing root prior to installation of the tank?
@RANSDesignsInc Жыл бұрын
It can be done through the wing root opening, lay your wing upside down and glue in place just as in the video.
@djquick Жыл бұрын
Excellent! More of these please!!
@bfryar22 Жыл бұрын
Holy crud. I did mine few weeks ago and there is no way you would ever figure this out given there are no instructions. Yes I did it but it won’t fit like this one. I won’t embarrass myself and tell you how long this step took me but it was A LOT.
@LTVoyager Жыл бұрын
I am glad I fit mine before putting on the outside skin. That made it much easier to fit the bracket and drill the hole.
@SkyRayden100 Жыл бұрын
Thanks Eddie! The videos are very helpful, keep them coming...
@Bushmasterpilot Жыл бұрын
Lol, I got ours fitting super tight, although it wasnt that hard without instructions, but you will have many happy builders now! Great video Eddie😉
@triav8n Жыл бұрын
Yessssss thanks Eddie
@lilianamalusardi4026 Жыл бұрын
👏👍
@triav8n Жыл бұрын
Nice camera work, BillyBob! Wish I had a good cameraperson. Keep up the good work!
@nathanprobst2164 Жыл бұрын
Bravo! Every one of these tech tips is gold!
@rjbishop12 2 жыл бұрын
Love the outtake! Merry Christmas Rans gang!
@lilianamalusardi4026 2 жыл бұрын
Merry Christmas 🎄
@home454164 2 жыл бұрын
Please extend wings and make an S-21 DeHavilland Beaver of LSA.
@speedomars 2 жыл бұрын
Would like to see this done again with the Rotax 915iS setup.
@Phoenixx5115 2 жыл бұрын
Yes! And I would like to see a gear option with 29 inch tires.
@dashriprock2916 3 жыл бұрын
To bad they won't answer the phone or return calls, I'll take my business elsewhere. Just ordered a glastar which the basic design of the plane looks amazingly the same minus the glass, and is much more refined.
@speedomars 2 жыл бұрын
Its COVID dude. They have 3.5 years of backorders.
@djquick 3 жыл бұрын
How well does a 6’4” 230lb person fit?
@MarkSDCA 3 жыл бұрын
I think you need to add some more videos.
@terrywirgau6111 3 жыл бұрын
I own a S-5 , its a great plane. Thanks for the cool video.
@kathya.653 3 жыл бұрын
#FLYRANS - This is one of the reasons I fly RANS - the artistry of the finished product - no one else finishes off their kits to look at sharp as RANS!
@Hamperokken 3 жыл бұрын
Shame they don't offer the 141 for the S20 any more. I suppose it just was too close to the S21.
@vergezac 3 жыл бұрын
Hy guys! I do own a S-6ES 912S Wing 116 here in France since 2020 an I have to tell you that "You've done a fucking good job with this stuff!'' I've got tones of fun every weekend because of you guys! Plz make more vidéos on KZbin your planes are very famous in France ! Kit Fox sucks here.. Rans are great value for the price here event if they're a bit more expensive than Best of Skyranger because they're a lot more fun! Skyranger are every where and just stuck in the air.. Rans is for real ''Coyboy'' ☺️😎
@Heather22056 3 жыл бұрын
Good looking plane 👌
@kennanok9089 3 жыл бұрын
VGs?
@456Broscowagner 4 жыл бұрын
SHOW... HELLO I REALLY WANT TO WORK WITH YOU HOW CAN I ACHIEVE THIS OBJECTIVE THANK YOU FOR YOUR ATTENTION
@mikeryan6277 4 жыл бұрын
As God as my witness, one day S7, S20 or S21
@andrewmorris3479 4 жыл бұрын
Awesome video y’all!
@baronlund9725 4 жыл бұрын
Why not use aluminum? Embedded fitting in plastic can leak later after you have your nice bird done. Why take the chance.
@randyschlitter2074 4 жыл бұрын
The fittings are not embedded, they are a design we have used for decades on thousands of tanks with great success, no doubt because of the "O"ring and flat washer seals incorporated into the design.
@baronlund9725 4 жыл бұрын
@@randyschlitter2074 Hey Randy, I check out the wing construction video and then seen how you were doing the fuel tanks without using those embedded fittings. Good job.
@davidboyle3032 4 жыл бұрын
Manufacturer Model Published Cabin Width Rans S-6 Coyote 2 45 Inches, S-20 Raven 46 Inches, S-21 Outbound 46.5 Inches Just Aircraft Highlander, Superstol , Supersol XL 44 Inches Kitfox Series 7 Supersport, Speedster, STi 43 Inches Cessna 172 Skyhawk, 182 Skylane 42 Inches Piper Archer LX 42 Inches
@Captndarty 4 жыл бұрын
Love this! More Outbound videos please
@davidboyle3032 4 жыл бұрын
Manufacturer Model Published Cabin Width Rans S-6 Coyote 2 45 Inches, S-20 Raven 46 Inches, S-21 Outbound 46.5 Inches Just Aircraft Highlander, Superstol , Supersol XL 44 Inches Kitfox Series 7 Supersport, Speedster, STi 43 Inches Cessna 172 Skyhawk, 182 Skylane 42 Inches Piper Archer LX 42 Inches
@LTVoyager 4 жыл бұрын
I just picked up my kit and hauled it home. I hope to #FlyRANS within a couple of years and the fast build design along with the high wing are two of the reasons I chose RANS rather than Vans.
@RANSDesignsInc 4 жыл бұрын
That's exciting, congratulations! Those are both excellent reasons to #FlyRANS 😉. Thank you for being a loyal and supportive customer!
@highflyer2488 4 жыл бұрын
Hoping to order an S-21 kit before the end of the year! #FlyRans
@RANSDesignsInc 4 жыл бұрын
Building an S-21 in 2021, are we?! Feel free to email [email protected] if you have any questions about the kit!
@c21delta94 4 жыл бұрын
#flyrans I love this aircraft. #FlyRans
@2FlyAmerica 4 жыл бұрын
Great Job, didn't know 2 10" Garmin's would fit in the panel!
@RANSDesignsInc 4 жыл бұрын
Well, now you know 😉!
@downandlocked7387 4 жыл бұрын
Thanks for the presentation, please add more they are extremely helpful!
@RANSDesignsInc 4 жыл бұрын
We're glad you found it helpful-more is on the way!
@downandlocked7387 4 жыл бұрын
RANS Designs, Inc. 😍🙏🏻. So excited!!! There are so few detailed videos about this amazing aircraft, for those of us not able to get to the factory or see one somewhere else in person. Can’t wait 🍿
@rickwiggins283 4 жыл бұрын
Professional and detailed! Thank you.
@RANSDesignsInc 4 жыл бұрын
Thanks-we're glad you enjoyed it!
@Project2Workshop 4 жыл бұрын
Great looking airplane! Can’t wait for my kit to arrive so I can #FlyRANS
@RANSDesignsInc 4 жыл бұрын
Our production crew is working hard to stay on track and keep deliveries rolling. We can't wait to deliver your kit to get you started!
@Project2Workshop 4 жыл бұрын
I’m on the list for a September pick up so it won’t be long!
@RANSDesignsInc 4 жыл бұрын
@@Project2Workshop Glad to hear it! Have you given thought to attending our Rudder Build seminar on September 18? If you haven't... www.cognitoforms.com/RANS1/RUDDERWORKSHOPBUILDSEMINAR
@Project2Workshop 4 жыл бұрын
Unfortunately I won’t be able to attend that event. Sounds like a fun time!
@RANSDesignsInc 4 жыл бұрын
@@Project2Workshop Congratulations! You've been selected as the winner of our #FlyRANS giveaway! Please email [email protected] with your t-shirt size, full name and shipping address so we can get your goodies on their way!
@SkyRayden100 4 жыл бұрын
Awesome! I plan on a similar panel with an iPad mount in place of the 2nd G3X. Very helpful. Looking forward to more content. #FlyRANS
@RANSDesignsInc 4 жыл бұрын
That's a great alternative. Our assembly crew recently completed an S-21LS (N21US) that uses a detachable iPad swivel mount, and it turned out great!
@SkyRayden100 4 жыл бұрын
@@RANSDesignsInc Question: What material is the black overlay and how do you imprint the labeling?
@RANSDesignsInc 4 жыл бұрын
@@SkyRayden100 Great question! It's actually a black two-layer matte plastic sheet with a white substrate that is exposed when the overlay is engraved. Most engraving shops are familiar with this type of material as it's very commonly used!
@edwardkuchera7699 4 жыл бұрын
Seems like this thing would be prefect with about a 32 foot wing span. I wonder why they clipped it
@warrenjbrown4898 4 жыл бұрын
An amazing all-around multi tasker!
@warrenjbrown4898 4 жыл бұрын
Nice , quick, slide slip at :53...
@TegoSuwarto 4 жыл бұрын
I like it