Tongue and groove, why didn't I think of that? Definitely going that route. How much reveal between the door and the door trim when closed. Is that adjustable if too open? Great easy to follow video, thanks!

Hey great info just put a 30x60 walk in with shower pan. Thinking just using approx 36”x78” fixed panel. Is LVT flooring alright in rest of bathroom? Thinking cause utilizing pan going without swinging door Advice? Do ya suggest the fixed panel or sliding door? And how about what type underlayment for lvt flooring ?

Very well done, perfect craftmanship.

Pro tip: Standard slope for good drainage is 1/4" per foot. Assuming you want to match the top of the deck to the top of the concrete, start (like you did) by anchoring the ledger to the concrete and then, to slope 1/4" per foot, use a 1" spacer at one end of a 4-foot level or a 2" spacer at one end of an 8-foot level. If you do it carefully, then the joists will match plenty well enough for a deck build and you'll have great drainage.

I really appreciate this thoughtful instruction. There seem to be about a dozen ways to do anything when it comes to showers... I'm going from an alcove tub...removing the end-wall away from the drain and going with 36x60 inch corner base (double threshold)...(and glass enclosure). I have not seen any products in-person...How happy are you with Dreamline? (I'm looking at Dreamline/Anzzi/Maax....with right hand drain and compatible with glass enclosure). Great Video.

I learned how you cut silicon tube.

Good video. You should try wrapping old 3.5” iron support posts in wood, it gets really tedious, but dang it looks good.

That grout was a nightmare fore us to get off the tile. It probably depends on the type of tile you use

I already have some pot lights in my kitchen. Is it possible to add a different fixture (same wattage) to the existing end of run daisy chained lights? Thx.

Wow this was a,fabulous build! I can't wait to try it

im a pro and ive had times when it was drying to quick , could have been becuase of humidity/ I also had a guy who mixed the whole bag up and it was rock hard in the bucket after 25 miuntes

Came to this video strictly to see what size cedar boards you’re using. You don’t mention it and you haven’t responded to a ton of people asking the same question. Thumbs down.

Can this wood be used in the bathroom?

Go for major brand lights. Cooper, Acuity, Progress, RAB, Topaz, etc. Those Amazon lights don't last long. Also, don't drill blind through joists. I'm glad you addressed this, but still super risky in most cases. For all you know your wire is running through the middle of your dryer vent right now. I have cut access holes many times and found all kinds of utilities that would have been damaged by this "blind drilling" method. I will never do it this way and do not recommend it.

Great video, music way too loud

What did you use to cover nail holes for final finish

Please avoid doing that. It's completely nonsense. The simplest thing that can happen is that you catch your wires on the drill bit. The saddest thing is to catch the neighbor’s wires from above.

I love how he just nails the pieces! I would become nuts measuring that the corner is really 90 degrees 😂 thank you very informative! Nice ideas

Very nice!!!

And if the whole frame is rotten underneath?? :)

These are the worst most annoying things for DIYers to replace. Hate these things.

I bought a borescope off Amazon for other purpose but would work great for this its only 50 dollars has a small camera that would let u see inside the ceiling

A great video thanks

It looks really bad being so textured. You did a good job, but roll on is not the way to go for a pro look

Awesome video! That new light fixture was very bright.

I did this and it started to bubble like crazy. I cleaned the surface so much and did everything I was supposed to do. I botched it

That Ultracolor grout drying time depends on multiple factors. Mix it with warm water and a spiral mixer, outside in the warm weather and you’re screwed. Mix it with cold water by hand and you’ll have all kinds of time.

Beautiful

Update? How is it holding up

Dude after watching about 5 of these videos this one looks like donkey dung.

Love the safety shoes :) Great job gonna try this for sure.

the ceramic bulb holders were probably getting super hot and causing the bulbs to blow

Thanks for the vote of confidence. I just used this stuff yesterday and have to say - it was pretty darn stressful - it's not very workable and it hardens so fast - luckily I was able to figure out that a wet sponge was able to slowly remove layers of grout that were too thick - all in all I was successful, but I have to ask - what's the benefit to having something set so quickly? Do professionals even want this hassle? By the time I had half the job done, the bucket was already hardening and I had to abandon the job - clean the tile - clean the buckets and all tools and start all over again an hour later. UGH! But it does look great.

How long until you painted the second coat? The directions say at least 1 hour, but that was too sticky for another coat. Other resources recommend a full day then sand it again....

How you doing

Awesome video. Thanks for sharing

Literally nothing but conversion videos, and not a single fresh install video, thanks for this. I know shit about working with electrical stuff.

Yep it really all is using a high-speed mixer even though it shows directions with a high-speed mixer don't use with high-speed mixer

I only have one bathroom. No way could I not use it for seven days

Led lights suck. No warmth. 3000k will make you old quick. Buy very low k

Jeff is a good guy but like all U tuber's he gave his opinion.

Great video thanks

When did you wire in the thermostat? Should have been extra wires for the thermostat? 3 wire from wall are coming from breaker where are the thermostat wire?

So I bought two of these as I have the same tile in my upstairs bathroom. I saw in the instructions that you have to use 400 or 600 grit sandpaper. When I tried that, the sheen wouldn't come off. Is that why you used 220 grit?

Extremely dangerous drilling blindly through floor joists, could be wires, plumbing pipes, alarm, cable & tell .

I don't know, sometimes it's best to pay extra for a professional. If you can find one that won't rip you off.

What an attractive guy and personality. Bro you supposed to be in movies.

Did you sleep in the same house that night?

dumb video

Looks nice, but I will do 45' cuts for corners.