This is the biggest project, I’m a car guy and will start this series today :)
@Romans828KJVКүн бұрын
cayman sucks
@jtscustomsNLКүн бұрын
Thanks for watching, have you seen the other videos of the cayman? Maybe you like it after that😅
@Romans828KJV17 сағат бұрын
@@jtscustomsNL lol I saw only two videos in the playlist was that all?
@jtscustomsNL4 сағат бұрын
@@Romans828KJV for now yess, but more will come
@Romans828KJVКүн бұрын
its revved in neutral or park
@jtscustomsNLКүн бұрын
In neutral💪🏻
@Romans828KJVКүн бұрын
europe is like a communist west if there was such a thing
@Romans828KJVКүн бұрын
what year is this man?
@jtscustomsNLКүн бұрын
Its from 2009
@Romans828KJV17 сағат бұрын
@@jtscustomsNL thank you I have a 2012 in Canada Vancouver
@jeffgamer19795 күн бұрын
Hello, I can try to help! This VAE valve is really bad, but it is only used for cold starts and air conditioning, the idle speed has a screw on the throttle body that needs to be adjusted. Regarding the brakes, remember to bleed all the calipers and even bleed the clutch actuator, as this will ensure that there is no air in the system. The TPS sensor can be adjusted to have more idle speed and also more or less power in the engine, it is not the cause of the idling problem, but test it with the multimeter on the ohm scale and see if the resistance is continuous, without any errors on the tracks within the TPS. The relief valve is connected to the vacuum hose that goes to the intake manifold, if so, that's correct. Well that's it for the moment, I have the same engine but it has FuelTech 500 which helps a lot with the setup, especially the turbo. Good luck, I hope I helped with something! Att. Jefferson Sorry for any writing errors, as I don't know English.
@jtscustomsNL5 күн бұрын
Wow!! Haha you say you dont know english and smash out this awesome explanation! Thank you very much for the tips!
@jeffgamer19797 күн бұрын
Hello, congratulations on the excellent video! I'm in Brazil and I was looking for a video like yours, and I have a doubt, since I'm far away, I need to cover the oil gallery, I was thinking about placing the piece itself with Loctite, with the holes outside the gallery location , keeping in mind that the smooth part of the bushing would block the oil passage. Do you believe this could work? Thank you very much in advance!
@jtscustomsNL7 күн бұрын
Thank you very much! I would not advice to do that, you will need to hammer them out and you can garantee that it will seal correctly. You can buy the kit at Projoe.com
@RafaelOliveira-mi2tp10 күн бұрын
Tudo bom amigo teria alguma dica para Solução do barulho do variador de faze Nestes motores?
@maryellis366119 күн бұрын
did the new bumper come painted?
@jtscustomsNL19 күн бұрын
No sadly not🤣
@maryellis366119 күн бұрын
what's the yellow thing hanging down on the front for
@jtscustomsNL19 күн бұрын
Thats a towhook!
@maryellis366118 күн бұрын
@@jtscustomsNL its connected to the grill area surly that cant be strong enough ?
@jtscustomsNL18 күн бұрын
@@maryellis3661 haha no its connected to the frame, its just hanging out trough the grill
@reaperreaper9593Ай бұрын
Can the crankshaft of the 1.8 be machined? I know the one on the 2.0 16v shouldn't be as the hardened layer is too tin. Did the engine last after the repair?
@jtscustomsNLАй бұрын
We brought it to a specialist workshop and the engine is still going strong💪😁
@manolomolina1274Ай бұрын
Netjes gedaan 👏👏
@jtscustomsNLАй бұрын
Dankjewel!!
@CharlesBarrosАй бұрын
Hello from Brazil! My brother and I have two yellow coupes. We are also in the quest to make it as pristine as possible. Great videos
@jtscustomsNLАй бұрын
Thanks mate! Good luck on your quest!!
@micheledimauro1282Ай бұрын
Happy to see it works! great job!!
@jtscustomsNLАй бұрын
Thank you!!
@liviaa.s864Ай бұрын
you are the best fiat coupe content creator 😮💨😮💨
@jtscustomsNLАй бұрын
Thank you so much!!! 😍
@CerberusbasscoversАй бұрын
So true!
@jtscustomsNLАй бұрын
@@Cerberusbasscovers to kind man! love it!
@liviaa.s864Ай бұрын
omg awesome video and I’m so happy that you made it !!!
@jtscustomsNLАй бұрын
Thank you!! 😊
@alfa156gtaАй бұрын
Great car !!!❤
@jtscustomsNLАй бұрын
Thank you!!
@sknuit1628Ай бұрын
you have spare parts from the older seats? Like the side plastic covers to sell? I also spotted you in a video or two about the viva Italia event, your coupe is so recognizable 🔥🔥 now is a beauty, i notice that you put the standard tail lights back in place, nice i prefer them
@jtscustomsNLАй бұрын
Hey, no i will not be taking the seats apart.. sorry. Maybe I will sell them as a pair. Yeah I prefer the oem lights aswell!
@sknuit1628Ай бұрын
@@jtscustomsNL i swapped the rear turn signal lens in my coupe (all 4 red) , but I had to remove the reverse gear light and move it to the plate lights
@jtscustomsNLАй бұрын
@@sknuit1628 that sounds like a cool upgrade. But that would not be allowed here in the netherlands
@kevinjekyll1521Ай бұрын
These are great cars, I have 2 20vt's. I like how where you are these are appreciated, where I live no one cares. NZ has no car culture of taste. Thanks for posting the car out and about, looks cool, Chris Bangel signed off on some really stunning and different cars. I have a few others as well, these cars are unique in a SUV cookie cutter EV world. All I can say is keep doing what you are doing... thumbs up from me.
@jtscustomsNLАй бұрын
Thank you so much! You either love the design or you dont. We also have a lot of people here who dont 😅 but we stand together with a group of lovers!
@kevinjekyll1521Ай бұрын
Yeah, I am so nuts that I just brought an Alfa Mito QV, and find the driving experience very similar, except the Coupe has that glorious 5 cyclinder note... Would love an Alfa with that Busso V6 engine it... Do you have any further projects in mind?
@jtscustomsNLАй бұрын
@@kevinjekyll1521 my mind is full of project. Like swapping an differant engine in it. V6 busso, v8 maserati or 3l inline 6 bmw 🤣🤣
@krismartin7215Ай бұрын
Awesome glad you made it
@jtscustomsNLАй бұрын
Thank you! It was a lot of work but we did it!
@coupeturbo6150Ай бұрын
👍 👍 👍
@truthrevealed9293Ай бұрын
After putting the lettering on the caliper’s following up with a clear coat to make sure the lettering doesn’t peel over time is the best way to secure the Porsche logo on the caliper’s.
@jtscustomsNLАй бұрын
Seen a couple of people do it and the clear didnt really stick to the decal and peeling of just as hard. Even seen some cases where the clearcoat even reacted to the decal and making a mess. So I chose to do it like this and see how long its stays on. So far its pefect😅 thanks for the tip though! Really appriciate it!
@truthrevealed9293Ай бұрын
@@jtscustomsNL No it’ll stick u gotta apply before the paint fully dry then the lettering then the clear coat. But if you’re happy that’s all that matters. Great job n vid
@bladibacar7445Ай бұрын
It runs?? 😮😮
@jtscustomsNLАй бұрын
Yess, more on that soon!😏
@micheledimauro1282Ай бұрын
@@jtscustomsNL ohhh yessss!!!
@Michael-wd4ozАй бұрын
Hello Mate , chnage olil put 10w50 or 10w60 ( in origin the engine was running 10w40 not 5w40 that`s for the modern cars, the engine is running in this way also for this issue )PS email were sent , have a good one
@Michael-wd4ozАй бұрын
Hello Mate i have a Coupe with your same setup and I am machcanic , you have one piece mounted wrong that could create this issue , ( in your intake manifold on the left side ,you have the air sensor hidle that should mounted in horizontally and not vertically ) check the manual ( if not clear I can send you an email with a pic how should mounted) PS don`t forget to map the car with the test bench , Good luck , enjoy your time
@jtscustomsNLАй бұрын
Heyy mate! Thanks for the tip! Do you mean the air temperature sensor on the back? If you want you can send me a mail at [email protected] thank you so much!!
@Michael-wd4ozАй бұрын
@@jtscustomsNL i will send you an email with some pic with your setup and mine don`t worry
@alexfergus1806Ай бұрын
really enjoyed watching this :) Keep going you'll solve it! If restoring a car was easy everyone would do it.
@jtscustomsNLАй бұрын
Thanks for the kind words! Someday it will be done!
@bladibacar7445Ай бұрын
Wish i had one.. Even if it doesnt run 🤣🤣🤣.. Good luck bro 🤞🍀👏👏
@bladibacar7445Ай бұрын
Also... I dont want to pretend to be smart.. I bet u did much more on cars than i did.. But i just went threw all or your coupe project videos... When u switched to kappa manifold..i didnt notice that u closed those 2 extra wacum lines that manifold had.. Or u just didnt mention it in video..if not mybe try with that.. Might be the issue 😅
@jtscustomsNLАй бұрын
Haha thanks for the tip! I closed them on purpose because I removed the fuel vapor recycling. The more I investigate the problems the more I think of reinstalling it. So you may be right😅
@bladibacar7445Ай бұрын
@@jtscustomsNL wish u good luck..so u can make some nice videos again soon 👏☺️🍀
@mitchreadwin19772 ай бұрын
Don't give up pal, you are doing a fantastic job
@jtscustomsNL2 ай бұрын
Thanks man! Just a short break and I will be back stronger🤟
@jaaps65352 ай бұрын
Gaat je lukken
@jtscustomsNL2 ай бұрын
Dankjewel!!
@Alesi32 ай бұрын
Respect for your efforts. 🫡
@jtscustomsNL2 ай бұрын
Thanks! It sure takes a lot of effort😅🥲
@micheledimauro12822 ай бұрын
don't give up! i'm fighting with mine too!!!
@jtscustomsNL2 ай бұрын
The battles are hard😂
@micheledimauro1282Ай бұрын
@@jtscustomsNL 😅
@krismartin72152 ай бұрын
Hey just a little bump in the road what a fantastic build !! I'm sure it will run right in the end!! Is that a intake manifold from an intergrale?
@jtscustomsNL2 ай бұрын
Its a bumpy road this one😂 the intake is from a lancia kappa.
@krismartin72152 ай бұрын
I have a 16vt coupe myself I love it!!
@krismartin72152 ай бұрын
Did the manifold bolt straight to the cylinder head with no adaptions?
@jtscustomsNL2 ай бұрын
It is a direct bolt on but it requires some trimming and a lot of relocating stuff to make it work😅
@arnietwo112 ай бұрын
Ohhh I feel your pain !! All that money and effort and no luck ?? I thot I'd upgrade over the winter my ignition system on my 1978 VW T2 campervan ! New power coil and electronic distributor! Ehh now it won't start 😢 Takes me back to 1998 when I restored a 1972 Lotus Elan. No modules or computer then, everything so simple 😊
@Wouterlambregts2 ай бұрын
dikke ombouw, ik heb een S5 b8, met een v8, prachtige wagen, ik vind die rs achterbumper wel erg dik, waar heb je die vandaan? En zou die passen op mijn s5?
@jtscustomsNL2 ай бұрын
Oeh de S5 is ook geweldig!! Ja deze bumper zou daar ook op passen met wat aanpassingen voor de uitlaat uiteraard. Ik heb deze bumper tweedehands gekocht uit Engeland. Maar ze zijn ook wel in duitsland op ebay te vinden en anders X-UK maar helaas zit je dan met importrechten
@cureroofingltd54432 ай бұрын
Faantastic paint job with 'rattle cans' but you've ruined the install with the white sealant. Black would have been better
@jtscustomsNL2 ай бұрын
Black would have been wayy better😅 but this is the stongest one I know. And I also trimmed it back later. You cant see anything now so all good
@arnietwo112 ай бұрын
Good job, can you tell me why oil and gasses go back into the air inlet ?? This causes build up of carbon etc as you know. So why is it not directed like you have done back into the sump ? Im thinking of adding catch can to my BMW F22, but am thinking why do manufacturers not re circulate it back into engine ?
@jtscustomsNL2 ай бұрын
Haha good question! This has to do with the environment.. car manufactures have to minimize the gasses that a car produces. So while its good for the environment, its not so good for the car as it will cost performance and will build up carbon
@MotherboardCircuit2 ай бұрын
Looks great on your car! I will be doing this upgrade very soon on my A5, I had a question I hope you can answer. The new bumper does not support fog lights so did you just leave them unplugged or did you just tuck them away somewhere? I don’t want to have error messages on my dash
@jtscustomsNL2 ай бұрын
The bumper kit I bought came with a blank off device where you can plug in the fog lights
@MotherboardCircuit2 ай бұрын
@@jtscustomsNL that’s handy! Thanks for the info
@user-ui3ed4wh1w2 ай бұрын
What colour you use?
@jtscustomsNL2 ай бұрын
This is performance yellow from foliatec
@user-ui3ed4wh1w2 ай бұрын
Is this enough for four calipers
@jtscustomsNL2 ай бұрын
@@user-ui3ed4wh1w yes it is but make sure you prepare all the brake calipers before you mix the paint with the hardener. Otherwise you run out of time
@user-ui3ed4wh1w2 ай бұрын
@@jtscustomsNL ok and how much i have to wait so i can drive the car
@jtscustomsNL2 ай бұрын
@@user-ui3ed4wh1w i would generally wait for 2 days
@ugovanmalderghem2 ай бұрын
you have a link ?
@jtscustomsNL2 ай бұрын
No sadly not, I bought it used here in the netherlands. You can always send TechArt an email. They also sell them directly
@edinsmajilovic71362 ай бұрын
Hello what is color code on fiat
@jtscustomsNL2 ай бұрын
The colorcode is FI 421/A
@CarLos-yi7ne2 ай бұрын
It misses a cylinder... 😁
@jtscustomsNL2 ай бұрын
Hahah nooo the others have a cylinder too much 🤣🤣
@rensschermer89563 ай бұрын
Niet slecht voor een it specialist
@jtscustomsNL3 ай бұрын
Ja inderdaad!
@nicolasc6173 ай бұрын
Very Nice !
@arnietwo113 ай бұрын
Good job ! Your tig looks different to mine ? I just fit the rods into the end and no need for gas. The problem with me is trying to keep the rod end just above but not touching the metal ! You didn't appear to have that issue ??
@jtscustomsNL3 ай бұрын
That sounds more like welding with an electrode and not this kind of TIG welding😅 do you also have a torch like me?
@WFORacer3 ай бұрын
You missed most important part. Center wheel cap must point to valve stem 😂😂😂
@jtscustomsNL3 ай бұрын
Oh snap! Now I have to do it all over again🤣🤣 I will sort it out once the wheels are off again💪
@geromefrieler96513 ай бұрын
"PromoSM" ✌️
@MrProvinspoul3 ай бұрын
Great work and result, I myself became the happy owner of a Cuope 2.0 16V from 1995, how wonderful to drive it and hear the fantastic engine, it brings back memories of when I had a Lancia Beta Cuope 1.8 from 1976, it's almost the same feeling of being at one with the car and the road. I would like the nice instrument you made in one of your other videos, is it one that can be bought from you? Thank you for your nice videos about the Coupe, but one thing that could be done without is the cursed "music" from KZbin, it is probably one of the most irritating and stressful things that has ever been made, there should almost be a law against it that it was not allowed to used so horrible it is to listen to.. Regards form Denmark
@jtscustomsNL3 ай бұрын
Thank you for the kind words! Awesome to hear that you have a Fiat Coupe as well. The barnacle widget cannot be bought from me but I put a emailadres in the discription of the video. Haha i love the music 😅🤣
@supleader42073 ай бұрын
Great Content Bro, a question with the transmission: is it only hold by Bolts and nuts, or do have to remove something else that i can seperate it from the motor? Thanks
@jtscustomsNL3 ай бұрын
Thanks man! No only hold on with Bolts and nuts. But dont forget the starter and the engine mount which is also attached to it
@cassiusbarros73333 ай бұрын
Bright! Excellent job. I was very interested, do you manufacture this digital unit for sale? If so, I would like to purchase one.
@jtscustomsNL3 ай бұрын
Hello! Thank you for watching! I do not make these myself. I put some information about in the discription of the video
@northernradical4 ай бұрын
Leuk filmpje. Net ff samen met mn zoon bekeken.
@jtscustomsNL4 ай бұрын
Wat gaaf! Hopelijk vond je zoon het leuk!
@alvaromontilla53814 ай бұрын
No es plug and play da fallo de airbag hay algún harnes