Sorry. I can't add music to my videos anymore, I was a newbie on KZbin when I made this video, music can be annoying sometimes

I can't show a lot because each product has different connection types, which can have dangerous consequences, I just tried to show the connection of the plus and minus in a simple way and the case of easy charging

kzbin.info/www/bejne/iZ3al3Wlm6yamLs

Электроникам не нравятся простые вещи😊

You're right, I tried it first, but I couldn't clean up the mess inside. yes.Sometimes it can work Thank you for watching the video,

kaulâh ta' nyaranaghhi è ponsel Namong manabi panjhennengngan orèng sè cè' profesional panjhennengngan bisa ngalakonè polana ponsel ghâpanèka cè' sakone'na kennengngan sè èsediaaghi kaulâh ta' nyaranaghhi è ponsel

If the drill is new, this will improve over time during the familiarization period. I don't think you need to return it, but if there is a loss of performance, you can return it

download links are available in the Description section of the video.

No, the voltages are not different ,it's not fast charging

I mentioned it in the description section

It can be defective cell or bad battery connection. You can try the dji battery repair program, but we can't know the exact result, You can try this or clean the pins of the batteries. Check if there is oxidation on the connection pins of the batteries. It's very difficult to say anything without trying.

@@MrSatech thanks, I will try

oui

Bonjour, je voulais vous demander si vous savez comment accéder à la prise de recharge du scooter Duatron Tugo

Je ne sais pas comment accéder à la prise du chargeur et elle est endommagée​@@MrSatech

dsl. Je ne connais pas grand chose aux trotinette électriques Dualtron Togo car ,ce nouveau modèle, Il serait avantageux d'aller chez un mécanicien dans un premier temps. Vous pourrez le réparer plus tard au fur et à mesure de votre apprentissage. Je suis désolé

@@MrSatech Bon mon ami, il ne se passe rien, merci de votre volonté, je le répare moi-même pour un client, mais je ne sais pas trop comment m'y prendre.

Could not perform SMBus read 0x00 dji battery? the error 'ERROR Could not perform SMBus read 0x00'. this means that there is no response from the BMS and/or the BMS is faulty and/or the battery is very low. See my second repair video on his channel, part 2

no.but, In the video I just showed how to do it in a simple way. Now you can do it according to your ability, I can't say it can't be done, it needs to be done properly and carefully.

The motor you're talking about seems to be a good fit

There is nothing paid, what are you talking about

couse need to pay for opening software​@@MrSatech

can u make video on how to install software in pc with out paying

I would be happy if you buy me a coffee. Link in the description.

@@MrSatech thankyoi

Skip ads, the program is free. Try skipping ads

yes

If you look at it in the description section video . I have added many links there

@@MrSatech thankyou

yes

@@MrSatech I can’t get it to work so far

hi. see video part 2 et part 3 Check out my channel

kzbin.info/www/bejne/moPXdHWAeqmoaNU Since the voltage inside the battery is low, it does not detect the electronic circuit, I suggest you look at the second part of my video

@@MrSatech 13,6v is inside . Is so low so the led is dead?

@@MrSatech 3.33 , 3,43 , 3,45 , 3,33 each cell

Remove the voltages of the batteries up to 4.2v, then try it, as I showed later, do a reset with the program from the computer, if you watch the video anyway. Eminem that we will succeed

@@MrSatech I charge each cell up to 3,90 (I didn't have time) but still the led is dead . The battery is holding the voltage well is not dropping but the button and the led is not blinking. Maybe the bms is broken. What do you think?

I don't know much about it either

flux solder

entre 30mn ~60mn lié au courant du module de charge que vous utilisez