Dji Drone Battery Fix-PART-1- DJI KILLER -cp 2112 module-dji battery repair

[@MrSatech]

Attention ⚠ Could not perform SMBus read 0x00 dji battery? the error 'ERROR Could not perform SMBus read 0x00'. this means that there is no response from the BMS and/or the BMS is faulty and/or the battery is very low. Dji mavic mini 3 shema pin : bit.ly/3QsxK9p

[@LuisEduardoCortés-s7y]

Hi, I couldn't. I have a Spark Drone and proved charging the batteries in the 2nd and 3rd conector (left to right order) with 12v but isn't worked. There is other solution without open the batteries?

[@MrSatech]

Hello, unfortunately, I could not find another solution. Even if you manage to revive the battery by applying voltage from outside, one of the cells will not be in the same alignment and at the same voltage, the problem will still occur. The solution I found is as I showed.

[@haibardolaza1]

@@MrSatech i have a good battery air2, it is charging well. so i tested the cp2112 and battery killer gnd, sda and scl are correctly positioned in respective battery pins but i still cant read the battery eventhough they are good ones, how come? the pins i used are all in the column1(left) side

[@symoto94]

non ho un alimentatore esterno per dare uno spunto alla mia batteria dji mini 2 ormai ferma da anni, come posso fare ? ho questo errore nel sistema, non da segni di vita

[@MrSatech]

Look at the videos on my channel, I made 3 part videos.

[@terrydawson6449]

Worked for me perfectly. On Spark batteries that has ZERO battery power, because they had been on a shelf for 3 years, had to add 12V, 1A to GRND and POSITIVE pins of battery to give the battery life to respond to READ/UNSEAL/CLEAR/RESET commands. Then charged up perfectly off regular charger. Worked on 6 of my batteries. Thanks for the video !

[@dan4vt]

How did you connect the 12 V to the ground? What cable?

[@dan4vt]

@terrydawson6449

[@Blud430]

how did you add 12v?

[@MrSatech]

Here the friend manually removed the battery and charged it by giving the battery pack 12v as the total voltage. But that's not healthy. Yes, it works, But not all battery cells are at the same level . As I showed in the second video, we must charge the battery cells one by one up to 4.2 v. The charge levels of the battery cells should be equal.

[@jim3920]

May I know that recovery process need to provide the extra power to battery ? I have two battery can't recharge. thanks

[@haibardolaza1]

yes they need extra power when programming eg. 12volts (air2) for those battery that have low voltaged and was refilled individually to reach 3.9 to 4volts each

[@jim3920]

​@@haibardolaza1 Thanks , the way was usefully recovery the drone battery ❤

[@haibardolaza1]

@@jim3920 yes but today i am encountering another problem with it. i was able to successfuly clear pfs and reset chip but power light is non functional unlike before a light goes steady now after the programming nothing happens and still cant charge or power it up.

[@knowyouryoga]

Hello, what do we call the three wires you connect from the module to battery

[@rabbitracinguk]

Do you have a link to the version of software you use in the vidio? The one in the link is the older 13.06.2021 but you are using the 26.06.2021 version.

[@MrSatech]

The stable version in the link I shared is

[@richardlong1567]

You did not show the pin-out for the DJI Drone 4 or Pro 4 Drone 3-SE ? Do you know where this info can be found? Cheers R from NZ.

[@MrSatech]

Unfortunately, this application does not cover all drones. I have not yet found an effective application other than the drones I showed at the end of the video.

[@thomasbalopitas5541]

great videos , thanks . one question mavic 2 battery what about if there is voltage in the battery but nothing happens when you press the button ? no led flashing , dead. broken pcb ?

[@MrSatech]

kzbin.info/www/bejne/moPXdHWAeqmoaNU Since the voltage inside the battery is low, it does not detect the electronic circuit, I suggest you look at the second part of my video

[@thomasbalopitas5541]

@@MrSatech 13,6v is inside . Is so low so the led is dead?

[@thomasbalopitas5541]

@@MrSatech 3.33 , 3,43 , 3,45 , 3,33 each cell

[@MrSatech]

Remove the voltages of the batteries up to 4.2v, then try it, as I showed later, do a reset with the program from the computer, if you watch the video anyway. Eminem that we will succeed

[@thomasbalopitas5541]

@@MrSatech I charge each cell up to 3,90 (I didn't have time) but still the led is dead . The battery is holding the voltage well is not dropping but the button and the led is not blinking. Maybe the bms is broken. What do you think?

[@niadafe]

Waaaaah. C'est une mine d'informations. Merci beaucoup pour ces développements et surtout pour les avoir mis à disposition. Je n'ai toujours pas ce problème sur mes 6 batteries de Spark après 5 ans d'utilisation occasionnelle mais je garde ça sous le coude pour le cas où.

[@Angelokrto]

Can I modify my Mini 2 for higher capacity cells and use this board to write the new values on the BMS?

[@MrSatech]

If you want to do this, you can do it anyway, since the batteries have a higher capacity, you will get more flight time. I don't know how you will modify the BMS, but I don't think it is necessary, because when the capacity increases, the flight time will also increase, but when the capacity increases, the drone becomes a little heavier and don't expect a very long flight time (maybe a few minutes longer), the extra weight will disrupt the stability of the drone.

[@michaelmagyar7813]

Where do you get the software

[@MrSatech]

download links are available in the Description section of the video.

[@therealchayd]

This also works for DJI Ronin-M batteries. SDA and SCL can be accessed either through test pads on the BMS board, or on a pair of contacts next to the power connectors.

[@MrSatech]

Thank you for your information. If you have tested it and it works, it will be very useful to other friends. thank you

[@chasiu75]

@@therealchayd You mean you don't need to open the battery and you can access through the small contact pads next to the power connections on the outside? Which pad is SDA and SCL? Where do you connect the ground?

[@stv5164]

please tell me if you tried this with ronin m it will work for such batteries

[@MrSatech]

@stv5164 Supporting models are mentioned at the end of the video

[@stv5164]

Isn't ronin m battery supported@MrSatech?

[@jamesreed7181]

Will this work on the Dji Mavic air 2 battery pack?

[@MrSatech]

yes

[@jamesreed7181]

@@MrSatech I can’t get it to work so far

[@MrSatech]

hi. see video part 2 et part 3 Check out my channel

[@kristiesimon9429]

Hello, I tried everything you did in the video for my spark batteries, but when i get to the software and click Connect, it says Error, Could not open device. Does that mean there is no hope for my Spark Batteries? Or is the Cp2112 board defective?

[@MrSatech]

To get rid of such a situation, I recommend you watch video 2. This is because the cells inside the battery are at low voltage and the electronic circuit of the battery cannot detect the batteries. If you look at the second video, of course it is a bit difficult, but I think you will be successful.

[@jamesreed7181]

What program did you use?

[@MrSatech]

The app is available in the Description section of the video

[@jamesreed7181]

This is a great video

[@channel-cz2uw]

ใช่โปรแกรมใหนเปิดไฟครับ

[@MrSatech]

ดูส่วนคำอธิบายของวิดีโอลิงค์ดาวน์โหลดของโปรแกรมที่มีอยู่ในส่วนคำอธิบายของวิดีโอ

[@dmitri679]

Can you please tell me if this can be done with the EV2400 or not?

[@airgun7674]

dji fpv battery also unlocked? Of the three data pins, the shorter one is for battery grounding and the second one is for data communication.

[@MrSatech]

As far as I know this program does not support fji fpv battery. I've never tried it

[@sofianenaanaa1588]

you can with all dji batteries, just look for sda and scl pins ;)

[@MrSatech]

Supported models at the end of the video

[@sebastianmuller6301]

is this working for DJI TB50 ?

[@MrSatech]

If you look carefully at the last part of the video, you will see the supported models, other models, unfortunately, they do not support it, I don't know either, I think that the electronic circuits in the batteries of other drones are not smart, that is, they are not suitable for programming. I hope I was able to help, I would appreciate it if you would like the video.

[@BerkutElectric]

Can you tell me on the mini 3 pro which contacts need to be connected?

[@MrSatech]

See it at the end of the video. There are compatible models and connections. Other models are incompatible.

[@BerkutElectric]

Thank you! But I was just watching at the end of the video on the mini 3 pro and there was no connection.@@MrSatech

[@StevenMetzTalks]

do you know what cells go in the origininal mavic air battery? It looks like 3s lipo but I dont kow the actual battery cell number i.e, 18650 21700 etc... I am not familiar with lipo

[@MrSatech]

a.aliexpress.com/_EIcK3sj

[@adelfomachado4190]

Esta celulas da pra adptar no drone spark

[@AI.ImaGen]

Very usefull video, Thx!

[@FERNANDOPENAS]

Where do I find the SCL SDA pin outs for the KF101 max Drone battery? I left the battery drained for months and now it wont charge.

[@MrSatech]

Incompatible model. Juste djı drone. Advice Open the inside of the battery and manually charge the batteries insidehttps. Example kzbin.info/www/bejne/rYq9iaaMfsecbdU

[@jasonkwc]

hi there i have click on all the unseal / unseal2 / clear PF / Clear PF2 / exit however my battery does not allow me to turn it off. it is stuck and permenantly switched on. please kindly advise.

[@MrSatech]

Hello my friend. After resetting your battery with the program, install the battery in the drone and you can turn off your battery normally after the drone is running

[@eyupensar8925]

hi god bless your hands, my drone dji spark, there is no spark section in the help section of the app, is that a problem?

[@MrSatech]

If you examine the video even better, at the very end of the video. I have given the connection diagrams of most batteries, the program automatically recognizes the drone battery. If it does not recognize the batteries, it means that your batteries have a low voltage. I recommend looking at Part 2 for this

[@eyupensar8925]

@@MrSatech thanks a lot, i order cp2112, thanks to your video i will finally solve my problem.

[@eyupensar8925]

@@MrSatech Let me ask one more thing, I have an arduino uno, can I do this reset with it, do you know? maybe need code for spark

[@MysticVibes48]

Eyup selam dji spark batarya problemini cozebildin mi? Benim 2 bataryada sarj olmuyor.

[@eyupensar8925]

@@MysticVibes48 bataryaları kullanmıyor muydunuz ve ne zamandır, 3'lü şarjda mı drone üzerinde mi şarj denediniz hiç ışık yandı mı tepki verdi mi

[@uctravel2614]

very clear instructions, thanks

[@Jaushan2256]

thank you so much i save 100$

[@taylor22270]

unable to read the battery, "ERROR could not perform SMBus read 0x00" any ideas or are the batteries to far gone?

[@MrSatech]

This is my second video You can also look at this Maybe you'll get an idea, kzbin.info/www/bejne/moPXdHWAeqmoaNU

[@CALL-ME-SLY]

Folks with 0x00 Error, I managed to fix it. Use this method, it worked for me - I found the solution. I just did a 10 secs video how i fixed the error - kzbin.info/www/bejne/rpCwknengbCKbsk

[@ricardopuerta]

Help please!!! trying the 2nd step: read info, it says: ERROR: Could not perform SMBus read 0x00. Am I doing something wrong, or my 2 batteries are dead?

[@MrSatech]

kzbin.info/www/bejne/moPXdHWAeqmoaNU

[@MASTER-td7qr]

У меня тоже самое😢

[@christianpien]

do you have a link for usb 12c communication module? or where did you buy it from?

[@MrSatech]

Aliexpress

[@davehill3034]

What is the pinout of the Mavic Pro battery (FB1-3830mAh) - is SDA and SCL available?

[@MrSatech]

Since these batteries are a little older, we cannot perform the operation with the same method. For these batteries, the process is more difficult. I can't tell you exactly, since it's not one of those batteries either. But you can go to this web address and get some information. www.laptopu.ro/community/reset-and-repair-dji-drone-battery/battery-model-dji-fb1-3830/

[@davehill3034]

@@MrSatech Thank you. Is there a more modern battery, with external SDL and SDA, that will fit Mavic Pro?

[@MrSatech]

Yes, For Mavic pro 2 and later. But by connecting your battery to a box repair you can have it repaired by a professional mechanic . But you have to pay a fee. I think look for a second-hand battery in good condition, there are a lot on the market, the most logical is like this.

[@ramim.5856]

I did the reset battery using the software but still cannot charge the battery it's zero empty no charge at all so is it damaged or I miss somthing or need to reset with much power? I used the power from the usb only when reset! Thanks

[@MrSatech]

If you have reset, there may be another problem, you need to be able to read the voltage of the battery through the program, if it is too low, there may be a problem, you can look at the 2nd part of the video, but first look at the voltage of the batteries from the info section of the program

[@ramim.5856]

@@MrSatech Thank you for the reply!

[@Joe-wk9ow]

Will this work to help balance new battery cells. I bought the Battery plus for the Mini 3 pro and I get high voltage error and I noticed that one of the cells has a 4.23v and the other cell is at 4.19v. I checked another battery and both cells read 4.19v. This battery now has 2 cycles on it.

[@MrSatech]

Charge the battery manually. When it comes to the same level, connect it to bms. And reset to bms with the program

[@Joe-wk9ow]

@@MrSatech the drone gives an error saying the voltage is high.

[@Cleanremove]

does phantom 4 battery included?

[@MrSatech]

To repair the Phantom 4 battery, you need to open the inside of the battery and charge it manually. If there is a voltage drop, you have to charge it manually. As far as I know, phantom 4 batteries are not smart batteries. So what we're doing here is that a newer technology can be applied on batteries. I hope I was able to help.

[@ChristianSanchez-qu2ku]

I did everything but it shows a message "Could not open device"

[@MrSatech]

Could not perform SMBus read 0x00 dji battery? the error 'ERROR Could not perform SMBus read 0x00'. this means that there is no response from the BMS and/or the BMS is faulty and/or the battery is very low. See my second repair video on his channel, part 2

[@forinfo1949]

hello, how about if the battery is totally dead, what if I replace the cell? it is the same procedure in what you did in this video? thank you. ill wait for your response.

[@MrSatech]

Yes, if your batteries are all down below 2 volts, i.e. dead, you can replace the batteries properly in accordance with the original, and when you repeat the process that I did Normally the battery will work.

[@MrSatech]

This is my second video You can also look at this Maybe you'll get an idea, kzbin.info/www/bejne/moPXdHWAeqmoaNU

[@forinfo1949]

@@MrSatech thank you for your response. I will try it by my self, hopefully it will work for me. more power to you.

[@terrydawson6449]

See my comment above - basically add 12V power to GRND and POSITIVE pins of battery while doing rest of the connections

[@angelvaca9232]

@@terrydawson6449 I have the Mavic 2 Pro and my battery has 4 positive pins and 4 GND pins, can I connect the 12volt to any of those 4 positive pins? Likewise the negative on any of the GND pins?

[@blacksmithz1]

Hello sir! It is posible to revive the dead spark battery for hybernation for 1 year without open the battery casing?

[@MrSatech]

I don't know. It can be done with a special machine. But you can look at part 2 of my video. That's how I solved the problem

[@binladen3773]

is it possible to do this repair on the dji agras T-30 battery? if so can you tell me which connection pins?

[@MrSatech]

Unfortunately.

[@gennaroborrelli919]

hi ihave some problem with a battery of Parrot ANAFI...have some solution to help me?...thanks

[@MrSatech]

I never repaired the Parrot anafi battery. But if you understand a little bit about these things, you should manually charge the low-voltage one by measuring the voltages of the battery cells.

[@HDBoy]

Hi, Thanks for doing this video. My DJI FPV battery won't charge because low voltage, is this software work with that kind battery also? Because I don't see that on the description and unfortunately I don't see the pinout.

[@MrSatech]

Normally you can't support it, but you can follow the friends who are interested in this topic from this page. Maybe they have reached a conclusion thank you for your interest in the video. github.com/o-gs/dji-firmware-tools/issues/229

[@HDBoy]

​@@MrSatech Thank you for your prompt response and help. My battery is few months old, I don't really want to throw it away

[@dissalex]

Did you manage to restore the battery?

[@HDBoy]

@@dissalex I left this battery on the charger for a day, hoped it works, but nothing happened, LEDs don't show up. If I'm right this DJI battery killer software doesn't support this chip in this battery. So I'm looking for solution to save this battery, many other person has same issue with DJI FPV battery.

[@anuruddaabeykoon3900]

Thank you so much dear🎉

[@ravibhadaniya]

Can i replace dead Mavic mini battery 18650 cells with new 18650 and unlock with software using CP2112 ??

[@MrSatech]

yes you can do this. But maybe it won't get the original performance and flight time. Technically, it happens. For example, if you have a good quality 18650 battery, Samsung 25r 18650.

[@ravibhadaniya]

@@MrSatech got it 👍🏻. I have placed order for hight discharge 18650 batteries and CP2112 Will post results 😁😁

[@Syclone0044]

@@ravibhadaniya Please reply when you have results! 👍🏼

[@ravibhadaniya]

@@MrSatech i changed mavic mini 18650 with new one and successfully unlocked battery Now my question that Original battery was soldered with spot welding, i used soldering iron to do joints Is it safe to use solder joints ??

[@MrSatech]

It is made from overheating. The main thing is not to heat the battery by leaving the soldering iron on the battery too much. The battery is sanded a little and the solder sticks out in a short time. So if you've paid attention to those, you'll try the battery and you'll see its performance.

[@Domizza]

hi, thanks for thevideo, does it run with the dji spark ? not seen in the list ... greetings -Domi

[@MrSatech]

Faites attention à la 5ème minute à la fin de la vidéo

[@Domizza]

@@MrSatech 😆c'est fait .....

[@yablofon]

is it works without +VCC from IC? Cause VCC from battery will kill IC board .....

[@MrSatech]

This is the method I found.

[@yasincengiz-turkey]

Send me videos links please 😊

[@mrdeeturk]

Hi, does the 3 wires come with the circuit board or do you buy them separate ?

[@MrSatech]

Unfortunately. You need to buy it separately or you make it

[@amirreza-jv2xd]

Hello, I have an m300 battery that at first gave an error when it was placed in the charger, and now it has completely turned off. Do you think this method works?

[@MrSatech]

With the app you can repair batteries of simple models of DJI drones, Yours is a professional model and you cannot repair it with this app. I recommend contacting a professional.

[@fredo19]

Would this work for phantom 4 batteries?

[@MrSatech]

No. Unfortunately

[@philmtx3fr]

Hi very interesting video for these wtf but expensive batteries... Thanks for that :). I just ordered at Aliexpress the chip but when I unzip the file for the program I get 3 files : one with _II, one with_FW and the last one with _IFIB... which one must I use with W10 ?

[@MrSatech]

If you download the file from the description section below the video, you will see that the name of the video program is Djı battery killer When you watch the video, I think you can be successful like other people There are also 2 parts of the video I recommend you to look at it

[@philmtx3fr]

@@MrSatech Hi MrSatech perhaps I badly explain my case : I found the file in the description. I found it on Mega. I downloaded it and it s a .far file. I extracted the files in it and there are 3 files with the same names except some suffix in it : _II, _FW and _IFIB. So my question is just which one must I use for windows 10. I hope it’s clearer like this. Thx in advance.

[@MrSatech]

DJI_Battery_Killer.exe. you need to find this file When you download the RAR file, open the rar archive in Windows 10 with the WinRaR program, if you do not recognize the WinRaR program, you can find it on the Internet

[@philmtx3fr]

@@MrSatech ok I will try this thx and sorry for annoyance ;)

[@beto021186]

what are the mavic pro battery pins?

[@MrSatech]

You can repair this battery with a professional tool, cp2112 This is incompatible with the battery, if it was the mavic pro 2 it was compatible. Search a low-used second-hand battery. Because the battery comes up with a very expensive repair cost even in a professional repair shop

[@GRiNGO-ADV]

Hello, thanks for the video! can i do this on a Mac?

[@MrSatech]

Unfortunately

[@Syclone0044]

When I connect CP2112 to USB windows PC, nothing happens. It does not detect any USB device. Do I have a defective CP2112 board? Or will it not work UNLESS a battery is connected via the 3 wires? I just got my CP2112 and was trying a basic test to ensure it’s a good board... I even used a USB test meter and it does not draw any current at all when plugged in.

[@MrSatech]

Try a different cable. Some cables are incompatible. Or another pc

[@AshrafRogers]

Hi. You need to install the drivers for the CP2112 first. It must detect even without a battery connected

[@Syclone0044]

@@AshrafRogers It actually doesn’t need any drivers as it’s standard USB HID Class Device. The answer is perplexing. I didn’t change anything, but plugging it into my Mac it was detected. Then I plugged it into my Windows PC and for some reason this time it worked. I fixed all my batteries, and then attempted to unplug and reconnect it, and now I can’t get it to appear again. Oh well, glad I managed to fix them!

[@AshrafRogers]

Partially correct. That HID device uses hid class device drivers built into windows. What I did find, as I use CP2112 as well as TI2300 to do battery repairs, is that com ports continuously changes when using either or. And I have to manually change this. Could be a conflicting device, bad drivers etc. If you plug in again and it detects, right click and check drivers location. See if you can manually update those ( copy paste method ), but you would need to go looking for those online. Glad you got it working 💪🏼

[@deweymhoke]

Hi I ordered the cp2112 how do I get the dji app for that I have 3 spark batters dead thanks I like your videos

[@MrSatech]

The program app. description is available in the Description section of the video

[@ravibhadaniya]

Can we use CP2102 module to connect battery to dji killer ?

[@MrSatech]

cp2102 does not work. Because it contains cp2102 signal chip. So it's very different. Not.

[@muhkadir6961]

Apa nama modulnya?

[@MrSatech]

Cp 2112

[@yasincengiz-turkey]

How to download DJI Battery Killer

[@MrSatech]

There are links in the Description section of the video, you can easily access the links after skipping the ads

[@revoltensolution]

Hi! Does the dji app works with mac?

[@MrSatech]

Unfortunately

[@revoltensolution]

@@MrSatech Thank you. I'll try with windows emulators. On the other hand, the cp2112 adaptor is in sale at aliexpress but where can we buy that cable? Can you specify an adress that sells the cable? my hope is revived after watching you video, maybe i would be able to fly my little spark after 2 years..

[@MrSatech]

The cable does not have a feature you can use a thin cable as you want. I can give the link to the cable from AliExpress:a.aliexpress.com/_Ewc2eet

[@revoltensolution]

@@MrSatech Thank you very much! One last question: Cables will be male-female or male-male?

[@MrSatech]

​​@@revoltensolution male female.

[@massam905]

Hi, where from can I download the software Dji battery killer. Please share link. Thanks

[@MrSatech]

Available in the Description section of the video

[@massam905]

Thank you mate 😊 you are legend

[@patrickfarnburn5704]

Nice but I have to mention for many users including myself it will not help, when connect the battery with the cp2112 adaptor to the computer and put in the program 'connect' it say it is connect but when you push the button 'Read Info' you will get the message: "ERROR could not perform SMBus read 0x00"

[@MrSatech]

Yes, I understand that the job is getting a little harder. This can happen if the voltage is low. But last , check the cable. If there is still no. here:kzbin.info/www/bejne/moPXdHWAeqmoaNU

[@patrickfarnburn5704]

@@MrSatech Okay, I'll give it a try again and will open the battery. Anyway, thank you very much for your quickly replay..

[@vishaalbisesser3749]

@@patrickfarnburn5704 hey patrick i got the same problem how can you solve it ?

[@patrickfarnburn5704]

@@vishaalbisesser3749 Unfortunately, not yet.

[@patrickfarnburn5704]

@@vishaalbisesser3749 YES!, after the advice from Mr. Satech to charge the batteries individual first, in my case, to 4,2V, and some repeating efforts with CP2112, it accept the batterie, and I was able to reset it.

[@Jimmy-pd3bv]

Hi, where do you download the software I can seem to find the download

[@MrSatech]

In the Description section

[@billywong7489]

what sofeware i need to use

[@MrSatech]

There is also a description section of the video

[@d.becker8195]

Hi, I could remove the PF error but my battery is still not charging. I have the 'SS' error too. Any idea how to solve this? thanks

[@MrSatech]

What exactly is the error message you are getting. (Ss) what is the thing. What drone do you use? Look at the second part of the video, maybe it will be useful

[@d.becker8195]

@@MrSatech I don’t get an error message. The PF thing works well but the battery is still not charging. Someone in another video commented that beside the PF error there might be an SS error. You can see it highlighted in red in the ‚register‘. Actually the newer Battery killer software is much more complex. Too complex for someone like me 😅 maybe a professionell should have a look… 😔 (The second video might be helpful but I didn’t want to open the battery as I don’t have a clue what I would do. I was hoping to solve the issue with the software)

[@bornanic]

How did you get Mavic 3? I downloaded it, but it didn't have Mavic 3

[@MrSatech]

There is a diagram at the end of the video. Program mavic 3 compatible

[@rmnjmljerryjet498]

Can anyone share where do i can get right link to download the software. All the link ive try out but none of them can be downloaded or missing link to download 🙏🏻

[@MrSatech]

Link Video In the description section

[@laaganvlog478]

Tested now?

[@wongjd4345]

my cp2112 board just arrived, when connecting, I got this error "ERROR: Could not perform SMBus read 0x00". any tips?

[@MrSatech]

See the second video kzbin.info/www/bejne/moPXdHWAeqmoaNU

[@wongjd4345]

@@MrSatech Thank you!

[@chazy10]

Does anyone have the printout scheme of mavic pro (1st series)?!

[@MrSatech]

No. No support.

[@laaganvlog478]

Tested? Mavic air 1?

[@MrSatech]

Yes, it is supported. . at the end of the video you can see the supporting models. If you have any other questions, you can ask.

[@derikgutierrez8386]

Hi everyone I’m getting an error code. Could not perform smbus read 0x00? Help

[@MrSatech]

Press the battery button while connecting. Try it that way This is my second video You can also look at this Maybe you'll get an idea, kzbin.info/www/bejne/moPXdHWAeqmoaNU

[@joescopo8933]

Well, I'm not very computer savvy, so maybe someone can help me out here. I downloaded the dji battery killer app, and to open it, my pc is asking me what application I'd like to use to open the app. I'm now confused on what to do next. I use windows 10.

[@MrSatech]

Winrar App.

[@Charon_Vlog]

adakah skhema untuk dji mini 3 / 3 pro ?

[@MrSatech]

Ebben a videóban megtalálhattam az információt, talán később jönnek új információk.

[@eprohoda]

fellow.beaautiful .=)

[@chopper8511]

I need the software, How can I get it?

[@MrSatech]

See video description

[@joescopo8933]

I can't get the app to work. It just says that the app is "not responding" when I click the unseal button. Oh well!

[@MrSatech]

kzbin.info/www/bejne/moPXdHWAeqmoaNU

[@joescopo8933]

​@Mr.Satech FR , I watched that video and downloaded the app from the link on that video, and used Winrar to open the app. I did open the battery and all 3 cells are showing between 1 and 2 volts, so I'll charge them to 4.2v and see if the app works. As of now when I open the app and click "connect" it says it's connected successfully. But when I click the "unseal," it doesn't do anything, and on the top of the app image, it says "not responding." I guess I'll let you know if it works after I charge the 3 cells. Thanks.

[@كثيرالطيب]

احسنت

[@imousschannel]

why i get did error message: ERROR: Could not open device

[@MrSatech]

Try pressing the power button. If it does not work look at the second part video

[@MusicAlanWalkerBaMusic]

mini 3 thaNK

[@yantoadja5851]

Download apk dji battery killer nya di mana?

[@MrSatech]

Video See description

[@celikcelik2719]

❤

[@condor4679123]

The app appears to be infected with Malware

[@MrSatech]

I and others have not encountered such a problem

[@condor4679123]

@@MrSatech can you put a link to the download location. I have just tried downloading from GitHub and Norton deleted the executable stating it was infected with malware?

[@MrSatech]

There is a link in the description of the video. And no one complained about it.