What year corolla? How do people leave that bit out

I had a frayed harness going towards my mass air flow sensor . The shop fixed the harness but said they were going to replace the ignition switch . Should I try to replace my fuse .

I have a 2013 Tacoma base cab, 2wd, 4 cylinder, manual transmission, and they removed most of the prewiring in this model (2012 to 2015). I had to get the cruise switch with the horn ground harness, which works out the same as your 3 pin connection. I also had to get a clutch switch and found the factory harness did have a connector for that, but no cruise light and I need to run a couple of wires (ground & ECM) and hope it will work then. The connector you were trying to get the female terminal pin out of has a little lock on the side opposite of the connector release, you have to pry it up just a tad and then you insert a push pin in the large hole to pull the wire terminal out. Glad your worked out easy and the earlier automatic transmission Tacoma's did too.

All that and no before and after pictures?

Thanks for making this video. Exactly fixed my steering issue.

Well that doesn't look like Ford coolant. With the extra additive. To help deal with the tremendous amount of cavitation ?

Thank you!

That fuse was exactly what the problem was. You have no idea how much we appreciate your video. Also. A new fuleline filter helped along with pre, and after the fule line pressure test, we did. Sir. Thank you very, very much!

2011-2016 front ones are even more difficult to access those front cage nuts! Great video

which model chases i have 1nrfe nsp120 does this same ?

Sir one request from India could you please make an video for how you opened up the steering airbag safely? Thanks for sharing this video.

Question i recently replaced the glow plugs and harness on a 09 f250 6.4 and now it wont crank any ideas of what could it be??

Excellent work

Thanks for the video. Is there anyway you could know for certain if a car already has cruise control installed if the switch is missing? I have a Camry 2005 Manual GLi. It has the 'CRUISE' logo on the instrument panel and also the hole where the cruise switch is supposed to be installed, but I'm not sure if that's the only thing missing. I've scoured the entire internet with no real luck.

.👍

Wow😮❤

Cool 😎 and good 😊 I hope you have a wonderful day

Nice

It's from NAPA. Their reman alternator. I've had great experience with their reman parts.

What brand alternator did u get

I bought the cruise control stalk and just installed into my 2018 Hiace van. Its not working at all, seems the van dont have prewired the cruise control system.

Praise the lord np leak I just did one that hurt

I was try on Land Cruiser prado 2015 model Type TX but it’s not working Can you help me sir

Good job! I'm glad you got it back on the road for them!

We’re so thankful for you and to all who chipped in financially! ❤

Hello, do you know if the Toyota avensis 2.0 vvt-i 2005 is compatible? (5 speed manual)

Kudos for your video. Your input was the key element in my successful endeavor to add cruise control to my 2010 Toyota Corolla base model. Oh, the thrill of victory! Thanks, again.

These Bahams sure do miss y’all!!

Good Luck! Down on the farm with Angie!

Anyone see the exhaust manifold bolt missing on the manifold by glow plug #7

Nice video i have nsp 120 manual chasis pls help

Had a similar problem with my 2006 Silverado took My pu to walliemart to buy a new battery after they changed the battery pu would not run mind you drove it in they called me and told me it was ready got there they told me it would crank but wouldn't run the alternator was bad so i called a tow truck turned out they didn't clean battery Cable was corroded cleaned cable and ran like a new pu I'll keep that in mind before I go to wallie mart there floor sweepers haven't been trained on cleaning battery cables lol

Somehow you managed to not show any of the actual removal....

Awesome! Also, that rooster sounds sickly.

Looking forward!

Can’t wait!!

At 16:00 reminds me of what my father would say when i was little, "if i look in your ear i can see right through to the other side" 🤣

Sir up, what is this fail pump checking box, sir, what is its name? I want to buy it.

Thank you for the clear instructions without any foolishness.

Sir fuel pump change name

Thank you !!! Thank you so much !!!

Great video! I tried taking the front ones out and when the nuts spun, I said not today. I just need to take the time and get it done.

So the tightening the gear didn't do it. I won't try.

Thanks man for the info. I go into the regen process after I change the oil. Even though I haven’t driven it more 300 miles. And the only thing I can think of is that the engine is NOT warming up and NOT running at proper temp from jump, like any other vehicle. 6 mins tops and any other car or truck with the exception of diesel , not sure But with my truck NO. Even when I’m running around town. It wasn’t like that at the beginning. That’s the only thing I can think of.

I recently bought 2008 f250 6.4. In tha past I have adjusted the steering gear on other vehicles but have not touched this one. The steering in it feels like the steering gear is boarder line to tight. Im wondering if someone didnt over tighten It. Now it dosent stick at a full turn, but on slight turns it will stay where you put it. So If your going around a slight left/right turn and let go of the wheel it will follow the turn till it reaches the end then if you didn't pull it back it would continue that same exact turn not snapping back to straight. I'm thinking maybe someone over adjusted the gear before they sold it? Only other things I can think of that would cause that are: Flat tires, Froze up ball joints, bent steer cylinder rod, bad piston seals in the cylinder, something with the hydrologic system like a sticky valve somewhere, The universal joint or joints on the steering shaft going from the steering wheel to the steering gear box are binding from rust ect, Or last but not least the steering gear is too tight. Any thoughts? Am i missing another cause? I have not had it in the air yet soon as I do I can eliminate a few things on that list just by unhooking things and grabbing the tire and steering by pushing on the tire. I'm thinking first I'll unhook each tie rod see if each wheel turns easy then put them back and unhook the power steering rack see if both wheels move easy together ect ect. Any thoughts would be helpful. Thanks

Isn't cylinder 5 on the passenger side?

Awesome

Good content, but a bit long winded.

is toyota corolla 141 2008 comes with cruise control?

Awesome vid I'm a jeep guy but love learnin new something new God bless you and yours