Good introduction

Very helpful! Could you please show me how to disable NTP on only one vEdge interface ?

Thanks for sharing mate. I enjoy your videos and also prepare for the CCIE with these vids.

thanks don nice concept

vpn-id's are Locally Significant. Having same vpn-id at 2 different sites does not mean they belong to the same customer/vpn and are reachable from each other. You are missing some important clues here, imo. what logical topology are you using by default? Full-mesh is the default and therefore all sites can reach each other without any additional policy configuration. Perhaps route-leaking only applies to different vpn's on the same vEdge as mentioned by other users mentioned in comment section. Any ideas?

hello Siva, why the PHP would happen b/w ingress PE & P router ? PHP happens b/w P router & Egress PE Router, is what I know . . .

Very smooth and clear to follow.

hello SivaKumar, i have few queries regarding your condition/offer for subscription. may I get your mail id, where I may connect u ????

@Siva can you please add vlan related questions also .

vedge# request root-cert-chain install /home/admin/Root.pem Uploading root-ca-cert-chain via VPN 0 Copying ... /home/admin/Root.pem via VPN 0 Error: Cannot upload root certificate file on a software vedge. Please use Viptela approved symantec signed certificates. Failed to install the root certificate chain !! vedge# IS THERE ANY ALTERNATIVE for this ERROR ?

Thanks for Video on Multicast. RP comes into picture in ASM mode. Looks like u have to mention the ASM first then Sparse mode. Is it possible to explain PIM with Sparse mode and Bidir mode.?

How did you enabled management access of vManager ?

what image you use for the server ?

Fantastic .. subscribed and liked .. keep up the good work and please post some videos on BGP and on TCP/IP ( MTU vs MSS , Sliding Windown, Slow Start etc ) ..

Shiva, the videos are excellent for clarifying concepts. If possible, could you consider creating some videos on MVPN as well? Thank you!

Thank you very much,,, after seen you're video i cleared broadcom interview with high package scale. It is helping to me all even how ping is work also

Great!

Hi.. can you help me with viptela-20.4.1.2-x86_64.tar.gz? i dont have cisco account. am stuck on 19.2.1 version and i want to change to IOS XE! Please!

If routing between 2 networks needed it will perform L3 function. In case of same network L2

Hi SK Pls post multicast Labs videos

what if my outgoing interface MTU is 1500 and my next hop connected interface MTU is 1000?

Very helpful video. Thanks for sharing

Awesome

Excellent, but please show the icmp packet and how ttl is decreased

How PC know the destination network is on same subnet or different ? Ans: Anding process

How PC know the destination network is on same subnet or different ? Ans: Anding process

very informative....thank you for your support

Thank you so much

what we can do if all the intefaces where a laptop needs to be plugged-in are optical?

What about copying files from your sdwan edge router to your ftp server. And also how to free up space on your sdwan edge router

Could you please explain what happens when a computer detects an IP address conflict and how the computer or switch responds to this situation? Thank you

Hi Siva, thanks for the nice explanation, I have one question regarding AAR , if the site has dual internet circuit (GOLD & SILVER ) and by default there will be ECMP but how we can configure the AAR to use the best available color for external web traffic ( I understand BFD can be used to measure path metric only over the tunnels) between the branch sites to any cloud hosted application over the public internet. In brownout situation can ip sla / endpoint-tracker usefull to measure the packet loss, latency & jitter for the underlay and fallback to pr0duction traffic to next available color. Plz share your expert advise on this.

Hi Shiva, Please try to add STP's, xSTPs, BGP, Dot1x protocol questions

thank you so much

useful, Thank you

Nice explanation

I wanted to download but it is paid

Thanks Shiva for the explanation ! Can you pls explain what is CEF table which is cited in the steps in the packet capture?

what will happen if we configure switch-10 egress port as access port and switch-20 ingress port as trunk port by allowing the vlan 10,20?

Informative video! BTW, which tool you're using for the lab simulation?

I just watched the video from the beginning, but one thing confused me: when you added the router to the vEdge for configuring BGP and OSPF, where did the router come from? Do we need to add it in EVE-NG and connect it to the SD-WAN to use the router?

Thanks boss..

Hi Siva, If we allow both Vlan 10 & 20 over trunk port between the switchs interfaces ,will it work?

which version you are running sir ? in eve-ng i can not configure bundle-ethernet the interface is always down

VRRP is l2 or L3 . some document say its l2 and some document L3 ? Can you share your

What if I allow both vlan on both switches then it should work right? Like Switchport trunk allowed vlan 10, 20 on switch 10 And switch port trunk allowed vlan 20, 10 on switch 20

nice explained

the question i want to ask is whether should RD and RT value be the same. If not why not ?

To establish the VRF it must use the physical interface, one interface per vrf. the loop back is use for ebgp as next hop self multibgp hop. ip address ipv4 between CE and PE1 then vpnv4 between PE1 and PE2. Penultimate hop pop is 2nd last router before PE egress LSR.

Thankx, I have a query. we have created multiple templates (enourmous amount) in a vmanage, now suppose i need to download the all of csv files for all of them in a single go , is it possible ? (is there any way to do it in vmanage ?) or i need to download each template individually by clicking that 3dots and Export CSV ?