Its is cable driven then? I was looking everywhere for some kind of booster or something. I have no experience with fourwheeler. My brake pedal sticks and i was wondering if it's something in the break drum sticking. Ill be tearing this apart now.

Wieviel Nm braucht die Achsmutter denn?

Do the clutch nuts need to be torqued to a certain spec? Should lock-tite be added to the clutch nuts?

My 1991 bayou 300 is really hard to pull over on compression stroke and when it does get running for about 10 seconds, it backfires through the carb too. I will try to adjust the valves and we will see how it goes. My quad is acting like the valves are waaaaaay too loose and the valve doesn't open soon enough so it gets stuck on compression stroke.

Czemu nie ma języka polskiego?

That was a great video thanks. I couldnt find the fill plug until I watch your video. Very helpful

Honda boy!!

Schneider Lock

I am going to start doing it today but would this work for my 2007 kawasaki brute force 650cc v-twin

I just picked up an 06 in mint condition... Very satisfied great vid thanks

I replaced my belt and slid the belt as far as it would go down on the primary clutch. I see this one is pretty much at the top. Maybe that's why it broke lol. Whoops.

Watching an add

I have the same battery. Most of the cells on it(probably 4 or 5 of them) are at the lower level line. Does that mean I need to refill it? And do I fill it with acid or distilled water? Ive been having a little bit of battery trouble but it still works ok after a charge.

FFWD 8 years from when this video was made . These aren’t cheap anymore. Cost today around 180/200$ per tire

Thanks so much for the information!

sweet helmet brah

I made the mistake of rushing the process now 4 short rides later (two night rides) my battery is shot and i am buying a new one today.

Is the 'knocking' sound under acceleration common? Mine does it and one other Sportsman 500 sounds the same. Has done this since I got it 10 years ago. I had a Kawasaki 300 years ago that made the same noise when on the gas.

At 37 seconds, what is the copper/brown looking part that he grazes with the wrench, on the way into the bolt? I obtained a used 2000 rancher, and it has that part, but someone seems to have "melted" a small hole near the bottom and inserted a gas overfill tube inside. 🤷

Thank you for this video and for telling me where the filter is! I couldnt find it. You helped me a lot <3

Hardest metal drum song to a mechanic video ever!!

Well done thank you

Hello, Are you interested in testing our products? We would like to invite you to test the Phone Holder for your 450 Rhino

How much torque on them nuts

Got a question. I had to replace front wheel bearings in the Brake Drum on a 94 Trx300 2x4. Should I grease the axle a little upon reinstalling the drum or is it ok just like it is?

What year is that bike

I'm amazed at how many people think 8' x 8' = 8 sqft! That's 64 folks. If you have an 8' wall that's 10' long, you need EIGHTY sqft of coverage.

How to drain the gas tank on your Honda atv electric shift

I have one of these on my Honda Rancher, yes, it’s expensive and it doesn’t do all that much, but I love what it does to the sound. Especially on a single cylinder engine, it definitely smooths out the puttering sound. I wish the manufacturers would give consumers a choice, someone like me, who uses it as a utility vehicle, I would like to have the bike as quiet as possible, others who are mud bogging etc. might want a more aggressive sound, let us have the choice. Thanks for the side by side comparison.

👍

I had a 2001 300 4x4. It was a great four-wheeler. And it had high low range. It would do the work that the 400 would do. Just a tad slower.

I didn’t know that there was a Rhino 450, i only knew the 660 / 700 ...

was curious if these were any good thanks for doing the review.

Thanks!

Recon is better no hussle.

Very informative video but the happy music in in the tutorial should be something much more metal. The rage that filled me when I got to the brake drum was overwhelming. Beating on it with a 5 lb hammer and torching it while soaking it with penetration oil. The spline not giving up and my hands black while mosquitoes are eating me alive. Please let me know if there's a step I missed while trying to take the drum off. It's an 1988 Fourtrax😅

Excellent!

im doing a outdoor patio bbq and grill area. thinking of using this for the face of the bar and counter area. that really looks nice. .

Nice video. Can you please update on what you think of it now? Did you have any heat problems? Loss of HP?

What diffence with filter code 5gh-13440-80 and 5gh-13440-60 Does he settle in both anyway? for kodiak 450 2003

How do you change the break cylinders I can’t find a video for the life of me

2024..still being referenced. You the man!

I had a old belt on mine never heard any squealing i put a brand new belt on and now it squeals alot any tips or reason why its doing that?? Please some one respond

My book says Valve Clearance (when cold) Exhaust: 0.20 ∼ 0.25 mm (0.0079 ∼ 0.0098 in.) Inlet: 0.10 ∼ 0.15 mm (0.0039 ∼ 0.0059 in.) your valves are super tight 😳😳😳😳 well ima try it on mine and lean toward the tight side

Which way does the oio filter cover go back on ? Where the filter dowel rests on the cover there is a slot , does it go down or up?

What year everybody's saying filter is too small

Great video thank you. Can they handle two people on board?.

Nice

Really cool and informative video, looks like these are about 7K dollar in base trim. Hard to decide what to get there are so many choices out there today.

i have a 2017 rancher 420 and it's flashing a dash after a very short ride. will it be rideable after it sits for a bit?