Marshall JCM 2000 TSL 60/601/602 are great amplifiers. They are all tube signal path and feature a parallel effects loop. And as far as I know, don't suffer from the thermal issues that lead to severe power tube bias drift as the TSL 100 amps did, before the main board upgrade by Marshall themselves from 2005 and onward. The main issue however with the TSL 60/601/602 amplifiers are the cheap transformers from the factory. I replaced both the mains and output transformers on my TSL 602, which I converted to a head, with Mercury Magnetics 'Axiom' line of transformers and installed a proper choke in place of the resistor. The circuit is dead factory stock and unaltered. That made a mega huge difference in improving the tone in all three channels of my TSL 602 'head'. Expensive, but worth it, as that upgrade took the sonic capabilities of my amp to a whole new level. Especially when cranked up quite loud as any Marshall amp should be. If you can get one, I highly recommend these Marshall amplifiers. Cheers!

Will it self oscillate?

How could i hook up two amps with one pedalboard and only one of the amps has an effects loop?

not for rythm guitar! garbage for me

Duchy! Please help! Hitting the Onion switcher everytime i want to engage FX Loop in other amp is extremely inconvenient when going into/out of a solo. Would it work if the switcher was permanently engaged? So when i switch amps on-the-fly the FX Loop is already angaged on the other amp.. Please help! - Love your work and thankyou for it 😊

This is perfect. I truly recommend the app to ALL levels of musicians. I as a beginner can easily be overwhelmed with all that it has to offer, For Free, I might add. Even the price for lifetime access to everything is very reasonable. With this, I will learn the guitar and play it well.

All good but please tune your guitars well man ,, cheers!

If anyone is still paying attention gonna reiterate a previous question. With a passive stereo splitter should I expect volume and or tone loss?

Hi. Nice pedal. Good demo. Is there a noise gate built in?

LOL. „Little bit of drive.“ Du meinst high gain crunch 😂

Go figure that that piece of junk pedal works better for guitar than it did for bass lol

Cool video, many thanks for sharing. I bought the Palmer Tino to switch my amps, but I did not consider the fx loops to split modulation pedals. I wonder if I can do the contrary you did, I mean that the main signal will be managed by the Palmer Tino, and for the fx loops, I’d like to try with 2 double jacks: one to connect to the output of the last modulation pedal to both SEND fx loops, and one more double cable to connnect both RETURNS to the first modulation pedal. Do you guys think it could work??

What if you want to have the fx loop on with both amps at the same time?

is it somting I don tunserstand : i want to hear, and hvae siganl from both ! amps, now just one and one. So how does that work =?

Or you could put a stereo pedal after the distortion to split the signal and use stereo effects in and out of the two effects loops.

I use this in my Atmos rig, actually sounds great. One of those Behringer products that's actually good.

I am searching one for month in the German aera where shipping is possible - no luck.

Sounds terrible

Thank you! Very informative!

Yes , leave the smoke in the transformer 🗯

Nice video. But you should turn the Master vol. up all the way up. and play with the tone and vol knobs. The amp will sound much better!

hello my friend. can you loop the chord progression?

Where is the link for this app ?

Prawda jest taka, że wali piachem na każdym drive, czy trzeba, czy nie trzeba. Nie idzie wyregulować na tym wzmacniaczu dobrego brzmienia do gitary rytmicznej. Zapomnij o blues-ie. Pewnie, że możesz grać blues ale brzmienia nie uzyskasz. Możesz ostro napierniczać lecz tylko i wyłącznie ze wspomnianym piachem. Chyba na pustyni projektowali schemat tego cuda. Ja przerobiłem swojego JCM2000 i jest teraz bardziej uniwersalny ale zaraz po zakupie to było rozczarowanie.

Yes please I need a footswitch for my jcm2000tsl60, where can I buy one.

What is the difference to the 100 watt tsl? Is it really only the power that makes the difference or is it also noticeable in the sound or pressure?

That is a beautiful color Les Paul. I have a couple questions for you. I have a 50w Plexi and a 50w Silver Jubilee handwired clone amps. Can I connect both these amps to my 4x12 cabinet and blend the sound together? How exactly would I wire that? Both my amps can do 4/8/16 ohms, and my cabinet does 4ohm mono, 16ohm mono, or 8ohm stereo. I'd like the tones to be blended. What about my effects? Would I put my pre-amp effects like overdrive and wah in front of the Plexi, and then all my other effects like reverd and delay in the FX loops of the Jubilee? Thanks!

Hi there! How do I know if my amps have a serial or parallel fx loop? I ve got a Marshall 2000 dsl 50 and a Carvin combo club master 112.Thanks!

Hi! Did you notice some signal or frequency loss in this setup? I wanna try to send a couple of pedals (strymon flint and a way huge delay pedal) in both fx loop of a Carvin club master combo and a Marshall jcm 2000 head. I didnt really understand about serial or parallel fx loops in amplifiers..It can work in both cases? If this works as I hope, you let me save a lot of money!! Thanks for this video🙏

hi, really cool idea. so i have one question: what amps do you have? are their individual fx-loops parallel or in series? i think, they're in series, if they were parallel your amp would not be muted, would it? thanks!

Does this works if one of the amps doesn't have and FX Loop?

What in the living fuck bro ? 🙄 Also sounds like complete dog shit 🤔🤘

love your energy, glad you showed each piece and it's differences.

I've owned about 4 of these through the years. Keep buying them and selling them missing etc. In Australia you can pick them up for like $500 2nd hand and they're such underrated monsters

I have same unit connected to Scarlett 18i20 3rd gen Scarlett (Master - Optical Out), ADA8200 (Slave - Optical In), but cant configure it with Cubase. Any tips? Thanks!

Can you just use 1 stereo pedal that has 2 ins and 2 outs… and from the effects loop on each amp.. thus: *From fx loop 1 the send goes to input 1 of pedal. *From fx loop 2 the send goes to input 2 of the pedal. *From fx loop 1 the return goes to output 2 of pedal. *From fx loop 2 the return goes to output 1 of the pedal.

Thanks for this video! It's great to know there are others out there pushing whats possible!

I have a Morley ABC Switcher pedal and have a question. How do I send output of my pedalboard that is connected to input of my amp to the pedal? Sorry to ask a dumb question but the inputs only allow one cable from each amp. I want to send pedalboard-> amp-> Morley switch pedal input A and then on amp 2 send output of pedalboard 2-> amp2 -> morley pedal input 2.

Very clever. The effects loop send breaks the signal when you switch between amps. Effectively you are sending you signal to the amp but you can't hear it because it never returns to the amp.

Once you have both amplifiers connected through the ABY pedal, how do you change amplifier channels at the same time???

Love mine. Bought it used in 2009. The previous owner had it modded at voodoo amps which tightened it up on the low end and made the tone controls more reactive. I used to play it next to my Bogner uberschall metal heaven!

I just can't get it to work :-( I have a 18i20 and ADA8200...can't get them to sync. Think I did everything as you did in your video...could it be the cable?

how about running 2 amps into 1 cabinet with attenuator in between ?

how about the attenuator to be connected to the Ampete? it is supposed to be between the amp and the cab

I have the TSL602 combo and the TSL60 half stack. They're my favorite amps.

Thank you for the video. I do have a question. In case a multi effect guitar processor has only 1 output which means I can't use 2 Amps if the Amps doesnt have an fxs loop (4 cable method). So can I get a "Y cable" to use that on my guitar Multi effect processor and its going to be connected from it to a (loop station) or whatever device that has R & L and thats going to split the signal to stereo, is that correct? Example: I will have the input from the multieffect unit sent to a loop station R & L (input) and have the amps coming out from the loopstation as stereo out R & L.

I bought this but in 100W for 300 euros.. excellent deal.. excellent sound.. one of the best sounding amps in my opinion

I just bought one of these with a Laney 4x12 cabinet for 350 euros.. an amazing deal. it's literally an amazing amp. I will eventually try it on my Marshall mode4 4x12 cab to see how it sounds with a different cab.. but as it is with the laney cab, it's a beautiful sounding amp. I can't compare it to a marshall because it has its own sound.

Odd question but do you know if these sound any good on the clean channel with a ds-1?

This was so helpful! Thanks a lot! Where are you from? Cool accent.