Жыл бұрын
Жыл бұрын
Пікірлер
@MrTwat86 4 ай бұрын
Doing a military base myself currently did you have to tie into any mass notification systems?
@terrance2405 Жыл бұрын
How can I turn off the beeping I work In a guard shack and I’m trying to figure out how to turn the beeping please help
@YourLocalFireAlarmTech 2 жыл бұрын
Only weird thing about this particular one is the "All clear" Message has an alarm whoop instead of a normal Chime lol but other than that pretty cool system. Silent Knight is pretty decent
@mrzugzug 2 жыл бұрын
Did you actually use the 6860? I am curious why you need both annunciators. Or is the 6860 just for the fire alarm?
@TheCarson116 2 жыл бұрын
Could you please reenable comments on two of your other videos by setting them as "Not For Kids"? (which really should be "General Audiences" instead)
@serg4220 2 жыл бұрын
Can you explain annunciator locations
@andrewbroughton6014 2 жыл бұрын
Not as scary as the traditional horn or bell notification
@figerking 3 жыл бұрын
How can I turn the volume up on the speakers?
@oscararredondo64 3 жыл бұрын
If your audio is too low, more than likely the audio was too low when recording to the EVS. If you are using the default tones and messages and your audio is too low, then you to change the speaker Tap. Example the EVS is 25volts. So you would normally set your speaker taps at 25 volt 1/4 watt for a Good audio volume. But if the speaker is set at 70 volt 1/4 watt the speaker will be very very low. Hope this helps and hope you understand what I am trying to say.
@figerking 3 жыл бұрын
So how to set it up to 70v?
@FireTech7 2 жыл бұрын
@@figerking the back of the speaker strobe
@jaxrules2892 3 жыл бұрын
WHY ARE THE AMBER STROBES FLASHING WITH THE FIRE ALARM MESSAGE? THAT’S NOT UP TO CODE
@joeycaridi3030 3 жыл бұрын
Because whenever you select the speaker messages it will make the amber alert strobes flash. Thats what the army base required when you select a speaker message. The white fire strobes will still flash when a pull station or detector gets activated
@FourtyFiftyEighty 3 жыл бұрын
Sounds like you need to reed the code again Jason Laferrier
@wilburepp8435 3 жыл бұрын
It is difficult to operate
@Roxxofoxxo 3 жыл бұрын
No Its very simple ngl
@usmanmughal7622 3 жыл бұрын
Hi, can you please share the wiring details how we connect IFP-FFT panel with main panel, secondly while wiring with amplifier we have to use both VBUS of main panel or we can use only one VBUS.. Any assistance means alot, looking forward for your positive reply..
@Tmoney064 4 жыл бұрын
Hey Oscar we are doing military base here with identical panel. I would like to chat about how you loaded the mp3 file for the message. Your system came out great!
@timglivefree Жыл бұрын
Same, ever get an answer on how ?
@Tmoney064 Жыл бұрын
@@timglivefree yes I believe the software is called voice load, but you have to create a text to speech file which you can use any software to make that
@Starshen1 4 жыл бұрын
can pick up the mic on the 6820EVS and announce on the speakers?
@oscararredondo64 4 жыл бұрын
Yes you can switch from the 6820EVS and the LOC-EVS and make announcements from either location. If you start at the main panel with the mic and you want to use the mic on the LOC you need to tell the the system you want to switch controls.
@alexandersalarms5380 4 жыл бұрын
uh yes?
@FireTech7 4 жыл бұрын
I cannot thank you enough for making this video. It's even in English :D
@supergabriel2042 2 жыл бұрын
I watch your videos. But is this video is this the cider that Inspired you to buy one
@FireTech7 2 жыл бұрын
@@supergabriel2042 I actually wanted one way before this video lol, didn't get a 6820 though, I got a ifp2000ecs which to me is a little bit cooler since there's 8 flexputs (input/outputs)
@supergabriel2042 2 жыл бұрын
I see
@gregorydebenedictus7449 4 жыл бұрын
Where did you get the voice messages from?
@firedetectioncompany-fdcos9769 4 жыл бұрын
I created them with a text to .mp3 converter
@firedetectioncompany-fdcos9769 4 жыл бұрын
I created them. I used a TEXT to MP3 converter. Which creates the Audio files. Then I made a Patch cord and wired it to the Input side of the audio panel and dumped them to the panel. VIA the steps from the manual. Pushing play on laptop and keying the mic then releasing the mic once message stops. Now you can pull the messages out of the panel for future use to dump into other panels.
@ZachS013 4 жыл бұрын
The reason you were having so much trouble with switching between messages is that you have to take "ECS control" at the FACU or the LOC before you can make changes. Also did you put a LOC at the remote building? If so how was that surge protected?
@firedetectioncompany-fdcos9769 4 жыл бұрын
I spoke wrong between the 2 buildings we have a 6820EVS and both 6820EVS have EVS-LOC. So between both buildings with have Single Mode Fiber Cards. And we have 6860 Remote Annunciator in Network Mode to display both Sites on the display. If you noticed I figured out that I had to log into the panel to take over controls.