Thank you my guy!!! I thought I messed up big time

I am deaf so you say noise on my gun would make not bother me😁

You know, we're not going to try to have.Some kind of stupid concert or just trying to figure on changing fluid in a differential and that wouldn't be so bad.Even put music on there if it wasn't so stupid and irritating.Come on man

I have a 2007 new body style which oil do i use dex vl or autotrak ll

I did this procedure, and it sucked, but worked, so sucking is OK. I was clumsy for the first few turns and scratched my barrel a bit - don't be me!

Music is retarded way to ruin your video bud

Socket size?

I didn’t hear it mentioned in the video so I’ll post it here since I just learned the hard way. Both plugs on the transfer case are npt threads. The deeper you screw them in, the wider they get. I just cracked my transfer case on the drain and didn’t wrench on it nearly as much as he did in the video. Really wish I’d have caught them being npt threads before putting them back in.

Thx for this info🙏

Thank you. I just received an upper from the factory with an oblong crushed washer. Was nervous about killing the threads.

Years later, and you my man, are a LIFE SAVER.

Yeah let’s use a fuckin metal screwdriver on plastic.🙄

Unfortunately, I did everything you did in this video.. and that onstar voice still comes on

The 09 Avalanche calls for 75W-90 gear oil for the rear differential and 80W-90 for the front according to the owner's manual.

Why would you want to disable onstar?

Thanks! I used vise grips and it worked!!!👍🏼

I didn't know buffer springs can make such loud music. Smart idea playing that when we're trying to hear a difference in sound.

DO NOT apply compound to the part, apply it to the tool AFTER it is lubed and inserted into the upper. NOT doing this ends up introducing compound into the interior of the receiver and you end up also lapping the INSIDE. I could literally hear the grit of the compound against the inside of the upper as the tool slid in. 😢

Before 0:37 After 7:03

Worked great, and no appreciable damage to the threads as promised. Appreciate the help.

And for the people that had some butt wipe at the factory over tighten a bird cage that didnt even have to be timed, crush their washer so there was no way to get it started on the threads, this is what I did. I used a small bearing splitter/puller and came in behind the washer snugging the splitter finger tight. Dont put it on the barrel. The tapered splitter will move the washer towards the barrel end and come partly between the washer and the barrel. Like I said, FINGER TIGHT!! I then threaded a 1/2"-28 nut on leaving about 3/16" hanging over the end of the barrel to protect the barrel and crown. I put a 1/4" flat piece of steel over that and mounted a Harmonic balancer puller to the bearing splitter. The Bearing splitter is tapered in the jaw and will grab the washer when you tighten the balancer puller. Dont use this to pull this off all the way. Its only to get the crush washer started so you can do what this guy is doing in the video. Just put enough pressure on to get the washer started. It wont take much. As you pull it a little the washer will catch the threads and straighten somewhat and get up on the threads. Once it does that you can do like the video. Frank who to the guy at PWS that did this. What a pain!! No damage to my barrel or threads. Some people used a dremel but I didnt feel safe doing that.

I took out. Plug. Seems. Like. Its overful. Is. Something. Wrong. I. Bought. Truck. Usded

I took out. Plug. Seems. Like. Its overful. Is. Something. Wrong. I. Bought. Truck. Usded

Thank you sir 👍👍

You got some balls using a crescent wrench.

Does it need limited slip fluid in the front?

Cmon! Wear gloves ffs

I trued this method didn't work. I was able to get an angle on the crush washer and cut a small piece withiut damaging the threads. Used a pair of snips and cut it then bent it a bit more and used two attempts with the snipe yo break it off piece by piece until it came off.

"Sliding buffer weight is gonna give away your location" ...wut a crock of HS. Can't take you seriously after that.

Thankyou

Yeah, I can't have my buffer rattle give away my position either.. When I'm ghillied up at the mall........

Mine won’t even thread

The one part I need to see you didn't show... Don't need 13 min to not explain to NOT explain the process. What a waste...

Thank you 🙏🙏🙏

Good afternoon, can you tell me the part code?

Can you tell me how to disable 4 g lte in newer vehicles? Will disabling onstar also disable 4 g lte?

If you ever came close to any gear lube, you know how foul it smells. If you get it on your skin, it tends to soak in and is difficult to get off. Wear rubber gloves and you'll be much happier.

thanks for sharing your experience. which part no. this replaced master cylinder

So, I basically did it the hard way and did it through the dipstick area instead of that big ol oil fill cap right there.......I hate this so much now.

Great advice, your videos are helpful and very informative.

Need to replace that booster has brake fluid in it. It’ll fail on you

thought the manual said like 3/4 inch below the fill plug ?

You are over tightening those bolts - that is an aluminum housing, you're going to wreck stuff! Should only be 18 ftlbs.

Bro I was told to place the truck on natural before moving the 2wd to auto and 4 high and 4 low. You had your truck on park no neutral

Thank you, Your video is really one of kind Made installing my running boards so much easier. Couldn’t find any other video with that weird DeF bracket

GM requires gear additive?

👍🏼

Where can I order for actuator part for my trailblazer 4x4 2013 model ltz

Is parts available?

Awesome video thanks👍