21 күн бұрын
Ай бұрын
Ай бұрын
2 ай бұрын
2 ай бұрын
2 ай бұрын
Пікірлер
@LeoThunderbolt1003 11 сағат бұрын
Nice a cml siren on top😂
@LeoThunderbolt1003 11 сағат бұрын
All even the XL Henry hopver
@arditov1 16 сағат бұрын
The video is really helpful but I have a v12 and there are no screws, how to open it ?
@vacuumhelp 15 сағат бұрын
@@arditov1 v12 models are a nightmare to open up even I avoid doing it at all. (Not the answer that you wanted to hear I’m sure) Try banging the dust out in the bin as a show and then a brand new filter. Then vacuum the house and take filter out to make sure it’s still clean (clean if needed) and then you may be ok. Tap the cyclone everytime you enmity and it may never happen again. Failing all of this. Ask around if any friends have a compressor to blast the dust out with compressed air. (Mechanics always have them) I do hope that you get sorted and don’t have to buy a new body from dyson. Jonny
@arditov1 10 сағат бұрын
@ I actually managed to clean it anyway thanks to your precious video! Works perfectly! Thank you so much !
@vacuumhelp 7 сағат бұрын
@ great news!!!!
@nate8932 19 сағат бұрын
How do you keep the housing for your pre motor filter so clean?🤣. Mines always dusty, even when cleaning the filter regularly
@vacuumhelp 19 сағат бұрын
@@nate8932 just SLIGHTLY damp microfibre cloth and a dry paint brush. I hadn’t notice this before you said 😂
@christiansears9335 Күн бұрын
Thanks for this video, clear and to the point - what all these videos should be like. Much appreciated.
@JC-tb2nm Күн бұрын
Concise. To the point. Effective. Many thanks!
@vacuumhelp Күн бұрын
@@JC-tb2nm thank you 🤩
@bananabirn2373 2 күн бұрын
I had the same issue. I tried hardly nothing happened 😂. Now, I will try this tip tomorrow. I am sure it is going to work. Thank you for your great help. 🎉
@vacuumhelp 2 күн бұрын
@@bananabirn2373 hope it does help 😊
@Lemonade-pc7uy 2 күн бұрын
Isnt this just chibi robo
@kristineauwers7851 2 күн бұрын
Thank you! This helped. Clog was in the handle.
@SaveHedgehogs 3 күн бұрын
Putting it navk together is a nightmare
@TelfLad 3 күн бұрын
taa buddy, hettys suckin like a pro again
@vacuumhelp 3 күн бұрын
@@TelfLad great news and thank you for commenting always makes my day
@murraymadness3653 3 күн бұрын
Great tutorial thanks! Really helpful. Cleaned and put back together so easy with your instruction.
@vacuumhelp 3 күн бұрын
@@murraymadness3653 great news and thank you for commenting 🥰
@pattybennett100 3 күн бұрын
Thanks, From O'Fallon, MO, USA
@vacuumhelp 3 күн бұрын
@@pattybennett100 you’re welcome and thank you for commenting 🥰
@ianmcardle8519 3 күн бұрын
Concise and accurate. Thank you.
@joedcruz5247 3 күн бұрын
Nice one, good tips.
@unkzzz 4 күн бұрын
This was helpful. It's lucky for me I happen to have a torx T8 lying around - I suspect this is not the case for many people. Not sure why they did that. Also, I had to sort of squeeze the runner onto the sleeve part with the two screws before it "snapped" into place. Not sure why but it was sitting out approx 1mm before I did this and was not seated properly even though it was in the correct place with the torx screw and the cyclone was also snug up against the vacuum. After it snapped into proper position I was able to put the two rear screws in last.
@vacuumhelp 3 күн бұрын
@@unkzzz thank you for your comment. I do have to agree with the torque screw thing. Dyson and Shark both use them and I dare say that it is so most people give up at the first hurdle and buy a new vacuum 😡
@vacuumhelp 3 күн бұрын
@@unkzzz oh also on the squeezing part. I think I know what you mean. Sometimes when you slide the cyclone back on it can be sat out of line (anyone one reading this I apologise for my lack of warning on the video) Just slide it off again and when you are sliding back on concentrate on the bin runner being perfectly in line with the part that it slides into. Like our friend here says it somehow just doesn’t sit right being 1mm out and the clone doesn’t seem to just come together perfectly. this ok would also cause issues with the bin being difficult to slide off if force it all together. My bad. I’m still learning from my errors of video production. It’s also sometime hard to describe what you do as second nature sometimes. Thank you for pointing this out
@vacuumhelp 4 күн бұрын
If you have found this video helpful please comment and LIKE 👍 Any interaction helps to keep the video alive so it can help more people in the future 🌎 If you are feeling generous click the THANKS button ❤ and make a small donation 💰 towards my next bottle of wine. 🍷 Jonny x
@robertdingley9405 4 күн бұрын
Thank you, all fixed from Watford
@vacuumhelp 4 күн бұрын
@@robertdingley9405 great news and thank you so much 😊😊😊
@paulcarlin9703 5 күн бұрын
Thanks - clear and honest and practical instructions 👍🏻
@vacuumhelp 5 күн бұрын
@@paulcarlin9703 thank you 🙏
@robrift 6 күн бұрын
If you use a plastic polish like Mother's headlight restorer and some polishing heads on a Dremel you can get it back to pretty much normal. I was bored and plastic polishing stuff was in arms length it is a little Overkill though.
@vacuumhelp 5 күн бұрын
@@robrift I’ll try dremel. I have polishing cones that I put on a drill which brings them up better. I don’t do many refurbs but I always like the customers in for repair to go out looking nice.
@tahirsoumaya5350 6 күн бұрын
Thank you ! Saved My day 🎉
@vacuumhelp 6 күн бұрын
@@tahirsoumaya5350 you’re welcome and your comment made my day 🥰
@AlexGarcia-yz3nc 6 күн бұрын
Tanks very step si correct, my two machine are good, best regars to Mexico City.
@vacuumhelp 6 күн бұрын
@@AlexGarcia-yz3nc De nada y muchas gracias por comentar.❤️
@SwiftMcJay 6 күн бұрын
Thanks
@vacuumhelp 6 күн бұрын
@@SwiftMcJay you’re welcome 😀
@ershadramezani6716 6 күн бұрын
I had no idea that there was an engine inside. I soaked it in soap water all night. Now engine still works but makes a load and strange sound. maybe because the oil in the engine is washed out and now too dry?
@vacuumhelp 6 күн бұрын
@@ershadramezani6716firstly I can’t believe it’s still working as such. Electrical motors are seriously sensitive to any moisture at all. The copper contacts and the bearings inside instantly take a dislike to it. They have to be microscopically smooth and water causes them not to be. No oil involved as electric doesn’t like that either. Sorry to hear of your predicament. You can buy new ones for £50-60 online
@vacuumhelp 7 күн бұрын
If you have found this video helpful please comment and LIKE 👍 Any interaction helps to keep the video alive so it can help more people in the future 🌎 If you are feeling generous click the THANKS button ❤ and make a small donation 💰 towards my next bottle of wine. 🍷 Jonny x
@vacuumhelp 7 күн бұрын
If you have found this video helpful please comment and LIKE If you are feeling generous click the THANKS button add make a small donation towards my next bottle of wine. Any interaction helps to keep the video alive to help more people in the future. Jonny x
@vacuumhelp 7 күн бұрын
If you have found this video helpful please comment and LIKE Any interaction helps to keep the video alive to help more people in the future. If you are feeling generous click the THANKS button add make a small donation towards my next bottle of wine. Jonny x
@allanwren2977 7 күн бұрын
Do you have to use a piggyback gold ending on the white wire if you just want the power switch and no led light?
@vacuumhelp 7 күн бұрын
@@allanwren2977 if you are just going without a light just follow the first minute of the video. Don’t need to change any connectors simply bang the white wires on the switch 🙂
@allanwren2977 7 күн бұрын
@@vacuumhelp also will it matter if i swap the hi lo switch with the power switch if it doesnt working putting the wires to the power switch?
@vacuumhelp 7 күн бұрын
@ if you have a green hi low you would be fine. Not the one with a light on though. If you feel it may be the switch, I have a video for sorting that out here…. kzbin.info/www/bejne/g3vHkIGie96CjsUsi=75GE1UzrBFMXPMLc Let me know how you get on with all this
@allanwren2977 7 күн бұрын
When bypassing the pcb board does it matter if you put the 2 white wires and the blue and brown wires on the inside or outside prongs of the underneath of the power switch and also does it matter if you put them on left or right?
@vacuumhelp 7 күн бұрын
@@allanwren2977 doesn’t matter which way around the white ones are. They can also be on the end 2 pins or the middle… aslong as they are together Here’s the bypass video kzbin.info/www/bejne/Z6bPpWqZhNWSgqssi=jsCRjoBpHv_xMXgK
@crikxouba 8 күн бұрын
How does the "unstretching" work? Cause it looks like it could be tedious to do from long to small.
@vacuumhelp 8 күн бұрын
@@crikxouba it just springs back to being short so you literally do nothing
@StefanNiculae0005 8 күн бұрын
😂😂😂😂❤❤❤❤
@tonymelissaj4333 9 күн бұрын
I’m from California. I hope this confuses someone. 😂
@vacuumhelp 9 күн бұрын
@@tonymelissaj4333 greetings from a snowy England 😊 thank you for joining in the fun in what otherwise is quite a full video 😂
@alinahahall 9 күн бұрын
Thank you so much!
@vacuumhelp 9 күн бұрын
You're welcome!
@nickgreen4731 9 күн бұрын
Easy when you know how... but you DO need to know how! Thanks!
@vacuumhelp 9 күн бұрын
@@nickgreen4731 think Henry manufactures are failing somewhere. This is by far my most popular video but it really shouldn’t be. It should be on the box of the vacuum and bags really
@nickgreen4731 9 күн бұрын
@vacuumhelp True! I could have figure it out, BUT my wife took the old bag out and left it like that, so I never saw the configuration inside 🤣
@eamonnd5501 9 күн бұрын
Thanks for your info on this! I tried this method several times with moderate success, but eventually, if not on the first vacuum, (after applying the method), then the subsequent vacuum...the hose would detach again! Shame I cannot add an image, but........the sure fire way that keeps the hose attached to the body, is to use HEAVY DUTY GREY DUCT TAPE. Buy it from any DIY store. After connecting the hose and fitting to the body of the vacuum, (as you explain)...you then wrap the duct tape around the fitting and for 6 inches or so up and around the hose as well. My Henry hose has not detached since I have done this...(over a year ago!). Thanks! ED
@vacuumhelp 9 күн бұрын
@@eamonnd5501 Litterally my biggest hate 😂
@stephanierose9071 9 күн бұрын
Brilliant demo. Thank you 😀
@dubqueen8484 9 күн бұрын
That’s three times in one day your videos have helped me out. Thank you very much squire! Extremely helpful stuff…had to subscribe. Bravo
@vacuumhelp 9 күн бұрын
@@dubqueen8484 crikey you are having a bad day 😂 glad that I helped tho and thank you so much 😊
@randomweirdyoutubechannel8955 9 күн бұрын
Not had this happen for a few years now last time i had something like this i put some superglue in and then screwed it back in dont thinks its coming back out even if i want it to
@4Cornerstube 10 күн бұрын
Hi Jonny, my DC25 switch is slightly different to yours. The grey brush button doesn’t have any resistance (no spring acting upon it), both the springs that you show are fitted, but there isn’t the metal clip that fits over the two buttons. Any ideas ?
@vacuumhelp 10 күн бұрын
@@4Cornerstube oddly some don’t have the metal part so dont be too concerned with that. When fitted the grey brush bar switch cover should press down onto the switch inside feeling a click on and off. If it’s not doing this, is the switch itself clicking on and off ok without the cover on?
@4Cornerstube 10 күн бұрын
Exactly that, switching the switch with out the cover switches the roller bar on and off. As soon as the cover is fitted the grey button does not move up or down.
@vacuumhelp 10 күн бұрын
@ ok I’ll try and help the way I can. 1. The grey switch inside, the lowest part is a curved shape. Is that ok? Not bork e or misshapen? Could it be CAREFULLY bet down slightly push the switch further down by just a fraction? 2. If you swap the actual switches around, using the power switch for the brush and the brush switch for the power…. Do they both behave then? I’ve had this before on some repairs when’re the switch seems fine but doesn’t behave with the cover and changing the switch for a brand new one worked. I’ve also opened some up before that have a little layer of electrical tape over the top of the actual switch… which must have been someone’s way of making the cover press down better on the switch. Annoying one I know and I hope I’m helping
@jenniferjohnson6974 7 күн бұрын
Just to clarify , is the on/off switch identical to the middle brush switch for the purpose of replacement. I've only seen the reset switch for sale, or the power switch. The middle one controls the roller as well doesn't it ?
@vacuumhelp 7 күн бұрын
@ yes the power switch and the floor tool switch are both the same 2 pin dyson switch found on every upright going
@LesleyBuckley1 10 күн бұрын
It's such a relief to find a video that just gets straight to the point with helpful information - that works! Thank you - great vid!
@vacuumhelp 10 күн бұрын
@@LesleyBuckley1 thank you. I can’t stand watching videos and waiting for them to actually do something 😂
@sqooot 11 күн бұрын
Super helpful!!
@vacuumhelp 11 күн бұрын
@@sqooot thank you. Hope you are back up and running again 😊
@sqooot 9 күн бұрын
@ yes and with a very clean home!
@barryhamiltonleenane 11 күн бұрын
Thanks mate. Fixed the problem.
@vacuumhelp 11 күн бұрын
@@barryhamiltonleenane great news 😊
@Interurmaw 11 күн бұрын
😢hjjuhhjj
@Amstroid 11 күн бұрын
Finally someone who doesn't repeat what is shown on the screen, but actually provides instructions on how to open it and clean it thoroughly! I couldn't manage to open the last part, with the flat screw, but I'm not giving up yet 😁
@vacuumhelp 11 күн бұрын
@ if you don’t manage don’t worry just give it all a good tap out. The most common parts are the channels anyway and the bit behind the grill which you can get to just by taking the bottom bit off. Make sure you have a clean and dry filter on afterwards and you should be trouble free for a while now.
@beatricegithendu688 11 күн бұрын
Hello Vacuum help. My Henry Hoover shows red light but when I switch on it doesn’t work. How do I resolve the problem? Could it be the green button?
@vacuumhelp 11 күн бұрын
@@beatricegithendu688 literally what this video is for if you vacuum has suddenly stopped working. Just follow video and should resolve
@beatricegithendu688 11 күн бұрын
Thank you. I will give it a go…
@vacuumhelp 11 күн бұрын
@@beatricegithendu688 let me know how you get on
@beatricegithendu688 11 күн бұрын
Just opened my one and found out that my red button has a little bulb…
@vacuumhelp 10 күн бұрын
@ ok that’s not the power switch that’s the high and low switch. This won’t be the issue you need to look at the on off switch (sometimes green sometimes red) Let me know if it cures it.
12 күн бұрын
Cleaned all the filters on the IZ400 ----- all 3 of them ---- the motor whistles constantly !!! Took out the filters and just ran the motor on its own. The motor whistles constantly !!!! Pain in the arse !!!
@vacuumhelp 12 күн бұрын
Ok if it’s whistling with no filters in it will be the motor bearings. Call shark as they will send new body under their 5 year warranty
@miralihosseini9625 12 күн бұрын
That’s a Nuvac but ok!
@vacuumhelp 12 күн бұрын
@@miralihosseini9625 never knew. Perhaps a great model for yourself.
@sineadfitz6500 13 күн бұрын
thank you
@sineadfitz6500 13 күн бұрын
where can you buy the bin flap only???
@vacuumhelp 13 күн бұрын
@@sineadfitz6500 for v7 and v8 here…. vacuumcleanerclinic.co.uk/products/dyson-v7-v8-dust-bin-lid?keyword=flap
@shaunnakettlewell5497 14 күн бұрын
Sukase