I appreciate you I’m always looking up tricks and tips on every car

How long does it take to replace?

Can the outer casing of the plug be taken apart further? I broke the latch on mine. Won’t draw it in tighter anymore. Will I need to re pin the wires to a new plug or can I just replace the casing/ latch setup??

How can I get or what is the name of that device for the targeter please?

What could cause the fuel gauge to read empty and the gas light blink? 2012 accord. Replaced the fuel pump already but that didn't fix the problem.

Unnecessary work, why clean? Will be dirty in about 100 miles.

I see this often with American KZbin videos where the license plate is blurred or masked out. Why is that a problem in the USA? What do you do when you are riding on the streets? Your license plate is clearly visible to anyone, as it should be. This seems very paranoid.

Ah, I see

Great video! Saved me from throwing away 3 new batteries that I thought were all dead. Many thanks!

Is the steering plunger brass? I think I sheared mine with my ass.... I was getting in my wife's car. She has short legs. I hit the steering wheel hard. It went into steering lock. Now it won't release no matter how much I jiggle or wiggle.

Toner wheel bad? Left exhaust bank 2 kzbin.infoVlkpmTdMKPE?feature=share

Help? Is this what a bad magnetic toner wheel on a cam looks like? kzbin.info-eo7Gj8mdfw?feature=share

That simple. Awesome. Thank you!

Thank you. That film is amazing

Doesn't work 2010 honda fit

Хунта бесполезная

What year and bike is this ?

Thad crank sensor motor o got any other one tramicion

Got saint problem car do saint thing no starer got 2 code 1 P 2076 the other one it P 2101 thing need to buy any sensor to fit it thad the crank sensor

The breakout box is a much more methodical design in my book.

I did control self test then message came up said error#1,what is it mean? Still have a same issue, Km/h still not match with RPM.i also replaced my new gauge control panel.please help

Superlative

Where can I get one of those switches? I can't find them

Thank you for the video. 👍

Thank you, sir bumping the key in with my hand was enough to get it to turn and come out. Thank you so much.

Thank you

Mine has grease ? Ridges on them .... Is that normal ? Should I clean them up ?

Latency is the fine tune valve that matches your ecm thinking and the actual output of fuel the same. Your ecm just turns fuel on and off, the latency is what scaled your ecm so the injectors are flowing the flow rate you told it to. Higher fuel pressure means smaller latency values to achieve the same flow

how to get this radar aiming tool ?

this is telling me that rising rate fuel pressure regulators on boosted applications to "compensate for increased manifold pressure" is sort of detrimental...

Thank you very much for this video! Very detailed and well described process.

Thanks for sharing your knowledge and exp on this

Thanks for the demonstration

Piezo injection Synchronous to ignition timing firing order how many bars of pressure ?

No, this is four years later, but just wanted to say amazing video for minutes and I realize what I needed because you did the hard work of pulling out the whole column with the center punch tool I may be able to just pull out the lock cylinder when I come back from Harbor freight getting a center punch tool again life saving video

A fish scale will work

Very helpful…. My husband got everything out and put everything back in and everything works on car except car engine won’t crank. Ac works, radio etc. just not engine.

What happens if you switch those and try to start the car?

How much should the re aim process cost? My local dealer gave a quote of $894 for "wave radar bracket and clips and re aim", does this sound right? I personally think it's way off. Btw this quote does not include replacing the radar because they said the radar is working, just need to replace the radar bracket.

Great video, chevy emc connector..the small pegs on the ecm connector has broken so i lost the ability to anchor in the wiring connector. I have managed to reconnect it but its not locked in. Any suggestion especially the broken peg is on the ecm unit, not the harness connector. Thanks russell

will this work on a 2007 Odyssey

My car was vandalized and stuck in lock so any other way ? 😢 my key did work and stop the day of replacement with my luck , please help 🙏

What's the chemical solvent used?

you can use hammer and screwdriver or hammer and chisel

Hey my Hyundai accent had the same issue where the switch cylinder (white mechanism at the back) went bad and my car needed programming, the mechanic bypassed the system and played with the wiring to add ignition and accessories switch along with a push start. This was my first experience and my car was stuck midway where the mechanic assisted me just wanted to know how much would it cost me if I need to do the complete ignition change along with programming??

How did you move the key to accessory position? Mine won’t move…does that mean I won’t be able to take it out at all?

Do you really need to take entire steering assembly to remove the cylinder? Is there any other way?

that was great, really appreciated it, however you didnt explain what part you replaced to make it work. this was helpful for me because my hyundai tirburon was stole, they removed the lock cylinder, and the ignition switch, and i need to decide weather i need to replace that housing or not. as i am ordering parts, and purchasing a new lock cylinder.

Body electrical shows up if you have a door open etc..

I have the same problem with my Hyundai ATOS from 2002 (manual transmission). I guess the components are very similar! But what part of this assembly should I suspect?? The thing where the key sits, or that long thing "downhill" (behind) from that? That thing which is aligned in the same direction as the key! Please please give me some hints, because I really need to solve this problem ASAP! The key is very worn I should add. We can unlock the steering lock, but cannot turn the key further to ignition position or start!