0:37 looks like Bugatti color 😂

Do you clay bar?

What PPF you used?

Is it better to cut out and remove the ppf on top of the camera housing? I see that you left the ppf over the side camera.

Like i am going to do this myself and ruin my Tesla. No Thank you for me doing this myself. This guy has probably done this for allot of years which he makes it look easy. Plus you have to have all the special tools and nice open garage area which I don't have.

Did you use any tack on the hood or just the edges?

Thank you

The template provided did not fit the actual letters. The letters were larger than the holes in the template for the letters. So pretty useless.

I have a full wrap for the entire car and the sensors are covered and work just fine. Why not cover the sensors?

Cool,,,thanks 🙏

What’s the mixture of alcohol and water?

do you sell precut 3m or xpel ppf in matte finish for the entire model y? checked your site but just see the front.

Why can’t you make a purchase on your site?

Where can I buy the PPF by bulk?

Took you 4 hours to do which means it will take me 4 weeks

How much alcohol do you use? 30%alcohol to 70%water?

Rrreally good video! Like it 👍🏼 Do you know how the ppf edges look like after 2-3 years specially on a white car? I have seen ppf edges that catch dirt over time you cannot clean because dirt is moving a bit under the ppf…

Great video! Question, any links for the steamer and the bottle you’re using? Thanks

Looks great. Thanks. I’ll be doing this in about a week or two. I figure its like a big screen protector. If i mess it up . I can do it again. Still save more money vs paying to get it done.

Great skills and that does not look at all easy to do, thank you for putting the video out there and sharing your knowledge.

Very nice work! I’ve seen several of these Tesla front bumper installs. You make it look easy but I’m sure it’s not. I would guess the approach for a first timer should be slow and patience with lots of soapy water, correct? I would think a beginner would tend to panic if things aren’t looking right instead of simply peeling it back and spraying it and trying again is this also a correct observation? If you keep the PPF wet can you keep working it for as long as it takes or will it tend to start stretching, drying, etc?

Very nice job! Why did you not show us how you reattach the Tesla logo on the hood?

Do you need to wax the vehicle in order to remove the dust particles ? What solution do you use to remove the dirt ?

This guy is using way to much soap if your clear bra is sliding all over the place your using to much soap usually from using the same bottle as tint. Also never put your fingers on the inside of the material. Especially on a white car

Your link is dead.

Excellent work - both on the installation and on the video.

How long dis it take you in real time?

This was the best PPF video for a Tesla DIY install I have seen yet! I know it’s not as easy as it seemed watching you, but your tips on aligning, and moving from one section at a time are great confidence builders. Very nice tutorial!

you make it look so easy omg and no heat gun needed?

You make look so easy. Thanks for the tips

I consider myself pretty handy person and I do not recommend people from doing this unless they have good experience(especially if you’ve purchased a pre-cut kit). Just pay a professional to do it. It’s just not worth it. The video makes it fairly easy to accomplish this, but it’s not that easy. If I had to really do this again, I would buy bulk and cut it myself. Buying a pre-cut PPF limits what you can do and you have to stretch different parts of the bumper just to get the alignments correct. Getting the parking sensor all aligned was such PIA! If i had a bulk PPF, i wouldn’t have to stretch it as much and I would have a lot more free pay with it-ultimately making things much easier to apply.

When will you do a ppf installation video for doors and the trunk bumper?

Due you are the best

Awesome video man, will do it today!

It does look to be nicely cut

Are you sure this is the correct way to install? Would make more sense to keep the front clear film on the front and apply. The kit needs a redesign.

Nice

They should incorporate murals, like the P40 Warhawks, for example, or some cool looking air intake or something creative.. Just for fun.. Instead of just plain clear..

Don't they make one of those strap-on leather front covers, like they had in the 80s? So when you're on a long road trip you can put it on and remove it when you're back home? They called them Bug Bra's...

You are flat out amazing. To do that on your own takes great skill.

Very Professional! What brand of steamer are you using?

What would you suggest the installation order if i have the full hood, full fender, bumper and mirror pre-cut kit?

What would you suggest the installation order if i have the full hood, full fender, bumper and mirror pre-cut kit?

Do you sell DIY PPF Xpel precut “clear” for 2021 Model Y? Can you give me a quote for complete coverage of car.

What is brand and model of steam cleaner?

Is that the same brand PPF you're selling on your website? XPEL Ultimate Plus?

I have a 21 GLE 350 and did 100% PPF. On the back rim under tailgate they have small cuts/gaps to make the PPF lay flat on the rounded edge. Is that normal? (Think of like laying a carpet and in a corner where they cut the carpet to lay flat)

The music was a bit loud compared to your voice.

What about using precut door edge trim pieces to do the wheel well edges under the plastic?

Do you also provide ceramic coating or paint correction? I'm located in the east end of the city and need ppf along with wrapping my roof gloss black.