fiok is that a long,boring video man...keep it short bro no one wants to see ya talking for 12minutes
@MrYmch13 күн бұрын
great video!
@brendonkadzsuraszik98274 күн бұрын
Kár, hogy nem a behajtóval kell letörni a fület! 👎🤣
@kerrid65666 күн бұрын
Just purchased one of these in Canada, to store paint and this video was a GREAT HELP!! Thank you so much for taking the time to show us all. The Instruction Book was not clear, and your video made everything to easy!🙂
@Adam-zw1ck7 күн бұрын
Franklin sensor. None are so reliable that you want to rely on it alone. Need to understand framing.
@soussolstudios35907 күн бұрын
How do you reset the windows on a cls merc
@RyoReznor8 күн бұрын
Completely fuxking usess
@RyoReznor8 күн бұрын
Garbage
@andrewb66039 күн бұрын
I came here knowing nothing and I left knowing less. Thanks.
@kunjcshah10 күн бұрын
Thanks Sir for providing this knowledge
@cristianbanuelos461910 күн бұрын
Did everything you said and still no hot water
@DriveFastEatGrass10 күн бұрын
What about female side
@lakermark200611 күн бұрын
this was a very helpful. is there a ballpark ratio that one can start with to reduce/minimize the amount of water and concrete to mix?
@decyntion11 күн бұрын
I wondered about that, after cutting through, pulling and breaking, grumbling and cursing at these little fairy light strings. I'll try this tomorrow and I have a good feeling about it. Thanks!
@BobbyKeeney-qw7zj11 күн бұрын
Where can you bye a chart with Bolts
@cattanmai12 күн бұрын
The instruction fast and easy for me who is first time to work with it
@me-pm6mx12 күн бұрын
You did good. Thank you.
@damianrantan16 күн бұрын
Lousy video. He drops it.
@213BRANDONP18 күн бұрын
Cordless Dremel will turn them all into flatheads😂
@213BRANDONP18 күн бұрын
At 5:22 you called them 1" bits ? Pretty sure they are 1\4 " hex bits
@hndflights19 күн бұрын
So much easier than using a rotating tool and all that BS
@klinkster195519 күн бұрын
What a salesman....review is like a 3rd grader giving a book report on a book he didnt read
@chriserickson441721 күн бұрын
Thank you. I think I can get this done. Putting in a Flagpole and I believe this is doable for me. Your video really helped me to get going in the right direction. Thanks again!
@frithfiver22 күн бұрын
I am embarrassed by how long I was failing at assembling this for. When I watched your video, it took 2 seconds! Thank you so much
@David-yo5ws24 күн бұрын
It may be 5 years old, but I got all the information I needed for a job tomorrow. And also reading through the comments, I got even more great tips to make the job easier. Thanks from the other side of the world in New Zealand, to all those people that contributed to this video.
@stevemawson826224 күн бұрын
great job thank you very helpful
@bonycells24 күн бұрын
It's masonry not masonary. Only one a in masonry.
@marksundberg801025 күн бұрын
Horrible instructions
@Pallidus_Rider26 күн бұрын
I just use my Dad's old garden rake and a mortar tub. 5 gallon bucket is too narrow to mix
@entertainmentarea48426 күн бұрын
Nice sweety
@lizziebydesign27 күн бұрын
This was ungodly helpful.
@Bigblackee327 күн бұрын
Thanks. One of my Go-to’s for automotive & shop information.
@groundedinfirstprinciples38328 күн бұрын
What kind of stud finder did you use that lit up and showed the studs that the small stud finder didn't find ?
@FishingWithDummies78Ай бұрын
doesnt help if you cant reach the back like replacing a rod holder e on a kayak
@phoenixmore8504Ай бұрын
GREAT JOB!!!!!
@chuletasexyАй бұрын
Will this work on stucco? I need to install earthquake straps for my outdoor water heater...
@Itsme-vo4fxАй бұрын
What anchor would you recommend to install an aluminum stair railing on concrete steps?
@LuisLopez-xe5llАй бұрын
It's easy with space try doing it on a transmission without space
@Paul.TheEpicTubeАй бұрын
couldn't expect anymore from a tutorial video.
@kevin_heslipАй бұрын
I like this corner of KZbin
@jerhughes75Ай бұрын
I have a bolt that nobody can tell me what they are. pretty sure they are grade 8. But head has 4 dots with IA on it. any ideas?
@Entropy106Ай бұрын
Excellent presentation
@blaynebyrd1106Ай бұрын
Hi thank you for the video, what size bit do I need for the sleeve?
@Knarf14Ай бұрын
So how do you remove a nut that is already galled up ?
@bludikaАй бұрын
this guy put 500 gallons of water for that little mix lol...
@JackJackKcajifyАй бұрын
"How to Properly Install & Remove Carriage Bolts | Fasteners 101" - doesnt mention pilot hole sizing and drilling
@complexity5545Ай бұрын
They never show how to put them on.
@tkmsleeАй бұрын
Thank you for this video! I was able to secure my diving platform by myself and feel confident about it!