Take that ring off when working on cars. Keep your fingers safe.

Thank you

Rotating distributor during placement Changes the Timing?

Hopeless must do better.

Spark plugs hole gaskets are broken on mine. I'm burning 3 quarts per week

Pvc valve doesn't come off????

This is actually a great instructional and informative video. Thanks for sharing.

Great video i don't care if it was a little long. Just replaced the distributor. I could tell someone had the distributor out at some point due to some RTV so i checked the timing before i took the old one out and it was way advanced. I got it back in spec now.

Why did you opt to replace it from under vs from the top side?

Just waiting for you to short out that on the battery.😢

Wao ,needs belt.

Muchas gracias por estos videos amigos no saben cuanta feria me arre

This saved me rn 🙏🏼 thank you

I am guessing this is a Nissan Sentra (US) or Pulsar (AUS). I had exactly the same issue, my needle gauge used to go past the middle section on the display when the car was under load (AC ON), and suddently when I turned the AC OFF the gauge will inmediately drop back down. When this happened I quicky checked the engine and everything was ok, so no overheating detected. (I did this by simply feeling the engine - DO NOT OPEN THE RADIATOR CAP WHEN THE CAR HAS REACHED NORMAL WORKING TEMPERATURE as it can burn you for life). I changed the temp sensor on my Pulsar and fixed the issue.

Hey man thanks for the video I will go get a can of carb cleaner and see if that's the issues am facing

Thanks bro Ik it’s been a couple of years since u uploaded this but u just help me go catless by explain how many bolts are on each side I didn’t wanna raise up my car to just see WWWW!!!

Great video! I think it's great that you know exactly what you're doing but you don't know certain terms for things. I can relate 😂😂😂 thanks man.

Life saver!

Do you have to torque them?

Is that expensive to repair

When can I get the distributor for this model I've looked for it everywhere even Spares shops can't find it

I’ve just replaced the rocker cover gasket on my 1998 Pulsar. The kit didn’t include the little gasket that fits over the oil duct, so halfway into my test drive the car started belching out masses of blue smoke. When I calmed down sufficiently to start thinking straight again (at first I thought I’d done some damage to the engine), I realised the small rectangular opening in the top of the cylinder head midway along the front is actually where oil is pumped to the rocker assembly, and the baffle inside the top of the cover is to distribute said oil where it is needed. Without that gasket the engine oil was being squirted all over the place inside the assembly, which is why it was burning oil. As I didn’t have a gasket to fit, I made one up from a piece of thick floor vinyl, sat it over the opening in the cylinder head and very carefully placed the rocker cover over the top. Problem solved, and just to be sure I took the oil filler cap off while the engine was idling and could see the rear camshaft having a decent coat of oil. Thanks for sharing the video, hope this bit of advice helps others.

Thanks for making the video. I'm no car mechanic so this is all new to me. I'm dealing with a "rattily" converter myself and trying to decided what I should do about it. Your video has given me an option. Again - thanks!

your doing just fine Travis,

How much tight in lbs to apply at distributor?

Topgasket replacs

Reset the timing

I would only unplug the one right on the end of the throttle butterfly axle the other one you unplugged is probably a air flow sensor

Leaving that starter between the two battery posts... had me nervous

I put in a new temp sensor because the fix finder scanner said it was bad, but after putting in the new one my truck had a hard time starting, then it just didn’t start, and when I put in the old one it started just fine.

Dude you need to learn how to make a video period. All that you are you showing as a damn oil filter

Yours in Manuel. Mine is Automatic Under The Car.....

I have automatic not manuel, mine is Under by Oil Filter.

Thank you very much Travis it did help me and I did it and it did work thanks a million could have cost me a lot of money but cost me just one light bulb 💡 😀🙏

Are you aware that if you connect a metal object between the 2 battery posts, that's really bad, right? Not a good idea to use your battery as a table.

You should change your belt bat thanks for the video

I'm dealing with the same situation right now I'm debating on finding if it's a leaky injector to be the cause of it melting the cat from raw fuel. Did you end up getting it replaced?

Wake me up when September ends

doesn't the distributer have an offset key which have to line up no matter how much you spin the rotor? so even you put in a brand new distributor isn't it supposed to line up with the keyway on the cam shaft?

Fiancé idle

I watched mostly to see if the guy was going to short out and blow up the battery with the starter laying on top of it. SOOOO CLOOOSE.

Thanks dude really appreciate this video

Thanks for the video Travis. Do you think the trans mount on an automatic 87 Stanza GXE is basically at the same spot? Few years ago had a shop replace all the engine mounts due to a clunking sound and movement which got a bit better but don't think they changed any trans mount so think that is the problem. Did you have to pull the battery to get to it or just can see it from below? So tired of the clunking when I put it in drive and reverse that I'm scared it might crack my automatic trans case. I have new KYB struts on it and it still is wish washy when I'm say doing 40 and move the steering wheel back and forth. Think it's because the trans mount has slop in it causing the front end to move aroud.

thanks for the the cluster removal video, since I have to take a customer unit out, you got lucky that the speedo started working, I have fixed plenty of issues related to the circuit board inside the dash Chris, Pacheco Speedo

I have a Nissan sunny B15 and oil come up In my spark plugs Please help me I’m form Mauritius

We're is the temperature sensor on a Nissan versa 2014

So mine is asking for a special clip he's really not made it?

if anyone does this, do NOT THROW AWAY THAT PLATINUM!!!!!!!!!! go recycle it for ALOT of money. thats why people steal them, because its precious metal. keep your metals from the cat and recycle them. hell, it might even be enough to buy you a new cat!

Haw to regane raining on a Nisan Sentra and replace bete for raining

Hey Travis, I drive a manual B14 too and recently i changed to new engine mount (all 4). Since then, when i put into reverse gear and near the bite point, the car vibrate/ shake strongly. Any suggestion on what happen?