Scrib Nibit

Пікірлер

@Dskora427 13 күн бұрын

Did you have to cut the screw so it doesn’t get in the way of the plunger? Like on the Glock 43x?

@scrib_nibit 12 күн бұрын

No. It was a simple install. No cutting necessary. Thanks for watching.

@TXLoneStar_ Ай бұрын

Ya get that Milt Sparks VM-2 yet?

@scrib_nibit Ай бұрын

Got it early September. Super comfy.

@TXLoneStar_ Ай бұрын

How has the Mark IV held up?

@scrib_nibit Ай бұрын

Phenomenally well.

@robertwymyslo9921 Ай бұрын

My m&p shield 9 is rusted and a lot of other people's have Smith & Wesson is junk

@TXLoneStar_ Ай бұрын

Weird. You're the only one that seems to have that problem. Stop using WD-40.

@scrib_nibit Ай бұрын

Only reason for any gun to rust is neglect.

@Mikey5-O 2 ай бұрын

@scrib_nibit just curious, what belt are you using? Thank you sir.

@scrib_nibit Ай бұрын

KORE Tactical Gun Belt | X7 Buckle & Reinforced Tactical Belt

@ConqueringAngel 2 ай бұрын

I just encountered the same zeroing problems yesterday after getting the eps carry. I’m Considering doing the same, how’s it shooting? Were you able to get zero?

@scrib_nibit 2 ай бұрын

Thanks for the question. Yes the S&W Shield plus w/Eps Carry was able to attain zero. 10-15 yds and beyond. I zeroed at 15yds.

@ConqueringAngel 2 ай бұрын

@@scrib_nibit awesome, I was pretty discouraged yesterday but glad to know there are solutions that worked for folks!

@stevevetter8045 3 ай бұрын

Way too high for OWB.

@scrib_nibit 2 ай бұрын

Hence the conceal ability.. It's a love / hate relationship. Can you mention any OWB Holsters that conceal so well? I know DeSantis has a pretty good one.

@TXLoneStar_ 5 ай бұрын

Just throwing this out there.....but do you have a shotgun and a way to clean it? Particularly the Mossberg 590 A1

@scrib_nibit 5 ай бұрын

I have that same shotgun. Never thought to put a video out to clean it. Thanks for the insight.

@TXLoneStar_ Ай бұрын

@@scrib_nibit Thanks.Appreciate it.

@GrumbleB 5 ай бұрын

Nameless is gooden fast 👍👍

@scrib_nibit 5 ай бұрын

No complaints here either....thanks for watching

@xzavierthompson2898 6 ай бұрын

Heard the eps carry MRS comes with rmsc to k adaptor that fits shield plus

@TXLoneStar_ 6 ай бұрын

It does , but due to the machining of the S&W Plus, using the adapter plate with the sight causes it to shoot high at 15 yards and runs out of (up and down) adjustment. At least it did with me....and Scrib's, He's the reason I sent mine off to have it milled correctly.

@xzavierthompson2898 6 ай бұрын

@@TXLoneStar_ thank you for the insight! I appreciate it !

@scrib_nibit 6 ай бұрын

@@xzavierthompson2898 TxLonestar is correct. We both ran out of elevation adjustment at 15 yards, Shots were still hitting too high using the adapter plate.

@xzavierthompson2898 6 ай бұрын

@@scrib_nibit thank you for the response!

@jeffreyehlers1605 8 ай бұрын

How is it working for you now and did they blue/rust proof or treat where they shaved?

@scrib_nibit 8 ай бұрын

Perfectly flat now and shoots great. They apply a sealant similar to T-9 BoeShield that protects against moisture. They can cerakote the optic cut for an additional charge of 30.00.

@davidh7078 8 ай бұрын

How much did nameless charge you?

@scrib_nibit 8 ай бұрын

59.99 www.namelessarms.com/product-page/m-p-shield-shield-plus-optic-ready-re-machine-for-holosun-507k-407k-eps

@charlesbeall2589 8 ай бұрын

Looks good if you're wearing a pup tent for a shirt.😆

@scrib_nibit 8 ай бұрын

Depends on your build.

@TXLoneStar_ 6 ай бұрын

I'd actually like to see that. Do share.

@Barrelsmoke 5 ай бұрын

I use this with a shield plus and wear fairly tight t shirts with minimal to no printing!

@mmafanatic-tz5or 10 ай бұрын

Do you send your optic as well?

@scrib_nibit 10 ай бұрын

If it is a re-machining job, no. If your gun doesn't have an optic pocket already cut, then yes....you need to send it with your optic. Give them a call. Really nice people to deal with.

@Mako-sz4qr 11 ай бұрын

Just what I needed thanks man 👍🏻

@scrib_nibit 10 ай бұрын

Glad that it helped. Thanks for watching!!

@floridajim3023 11 ай бұрын

This holster does a great job hiding my Glock 19! I just ordered the wing belt clips for it which will hold the holster even closer to my body . Thanks for the vid 😊

@scrib_nibit 11 ай бұрын

My pleasure. Thanks for watching!

@TXLoneStar_ 11 ай бұрын

I'd like to know more about how you manage to get this holster closer to your body. I see nothing about wing belt clips. Scrib?

@ecupirates98 11 ай бұрын

Is there a difference in cleaning a shield vs cleaning a shield plus?

@scrib_nibit 11 ай бұрын

From what I can tell, the only difference is the Mag capacity and trigger. The cleaning process is the same. Thanks for watching.

@TXLoneStar_ 11 ай бұрын

If I may offer some advice.....totally soak the patches before pushing them through with the jag.

@scrib_nibit 11 ай бұрын

Ya know, someone else mentioned that and I never snapped until I watched my own video. Good catch and yes....soak the patches, especially the center, when using a jag. You can also tightly wrap a bore brush, soak it, and do it that way. Thanks for the heads up.

@boomaster515 11 ай бұрын

how many holsters did you try before this one?

@scrib_nibit 11 ай бұрын

I have 2 other holsters for the Shield Plus, but they don't have the optic cut. A Vedder's and a Milt Sparks VM-2. This is the first optic cut iwb holster that I have tried with the gun. I have a Milt Sparks VM-2 with optic cut on order.....should be ready around Christmas 2024. Thanks for watching!

@boomaster515 11 ай бұрын

@@scrib_nibit will be checking it out if u ever do a video about it

@scrib_nibit 11 ай бұрын

@@boomaster515 This is a video about the holster. Let me know if there is something else that you would like to see and I'll see if can oblige. Shoot straight, shoot safe.

@hiramr1153 11 ай бұрын

Have this holster both for my Shield Plus PC 4” holosun and M&P 2.0, 4.25” with optic. Ready satisfied with this product.

@scrib_nibit 11 ай бұрын

They do cost more than the others, but it's worth it. Thanks for watching!

@mikkolangot 11 ай бұрын

Never looked back with any other holster after I owned one. Solid holster

@scrib_nibit 11 ай бұрын

I can see why. These holsters are great! Versatile and comfy. Thanks for watching!

@TXLoneStar_ Жыл бұрын

Beats using swabs.

@Gitrdun_ Жыл бұрын

Brilliant!

@ChopperKool Жыл бұрын

Gracias por los consejos... ¡Excelente tutorial!

@scrib_nibit Жыл бұрын

Muchas gracias.

@christopherreeves7915 Жыл бұрын

Tulster Oath can’t go wrong with this holster. I own a couple of these and they are great!

@TXLoneStar_ Жыл бұрын

Agreed. They cost more than most, but you can't beat the quality.

@scrib_nibit Жыл бұрын

Yes sir! Excellent holsters. Thanks for watching.

@TXLoneStar_ Жыл бұрын

If you want, you can adjust the cant. Sorry. That line always gets me.😄

@scrib_nibit Жыл бұрын

Ya, it does sound a lil' weird.

@daveb3404 Жыл бұрын

Does the bushing need to be between the spring/guide rod and takedown tool or can I reassemble with the bushing already off the guide rod? I had to send my slide back to Kimber and bought the NDX after attempting to use the paperclip 2X and found the NDX tool.

@Cyph3r_324 Жыл бұрын

Somewhere out there is someone who actually used red loctite..hehehe.

@TXLoneStar_ Жыл бұрын

Hey bro, need some trigger advice. Action on my OR Shield Plus 9 was smooth at the range, but after cleaning the gun, the trigger feels gritty after it hits the wall and breaks. It's smooth with the slide off, but gritty with the slide on. Could I have gotten some crud in the slide somehow? Thanks in advance.

@scrib_nibit Жыл бұрын

Happened to me once. There is some sort of debris/ or burr inside your striker pin safety. Push on the safety plunger at an angle and see if it feels gritty or rough. It should feel smooth. If not, try using compressed air and blowing out the striker channel first. Check for grittiness. If the grit is still there,, time to perform minor surgery. *_At your own risk._* There are videos out there to show you how to remove the striker pin safety. You have to loosen the screw on the rear sight and drift it to the left to remove the striker pin safety and check it for a burr or debris. A sight pusher really helps here. Be careful because there is a tiny spring and cap under there holding the safety plunger in. While you're in there, clean out the striker safety channel. Hope this helps. Anyone else, feel free to chime in if you have experienced this and fixed using a different method.

@TXLoneStar_ Жыл бұрын

@@scrib_nibit I have a buddy that works at Range USA gun range and has access to a sight pusher. I'm not going to take a hammer to it like in some of those videos. I tried the compressed air and it actually helped a bit. It's still not as smooth as it should be. I'll mess with it next weekend. Thanks.

@TXLoneStar_ Жыл бұрын

I found a video on it and it wasn't that hard. Harder to get that safety spring and cap back in, but it's together and working smoothly again. I sprayed some Hornady One Shot in it and swabbed around, dried it off, and put it together. I didn't see anything that could of been causing the grit. Must've been real small. Thanks for the help.

@markjf131 Жыл бұрын

Thank you. Very easy to follow.

@scrib_nibit Жыл бұрын

Glad it helped. Thanks for watching.

@TADDs101 Жыл бұрын

I just purchased this S&W Shield Plus and trying to learn as much as i can about it. One other video i watched showed the guy pulling the trigger and then pulling slide off ... does it matter? Is dry firing not recommended with this striker fired gun? GREAT video on how to clean and lubricate

@scrib_nibit Жыл бұрын

S&W added the sear release lever so that you don't have to pull the trigger to take off the slide. Sort of a reassurance that you won't accidentally fire off a round. It is safe to dry fire these guns, but if you are going to be doing _a lot_ of dry firing drills, I recommend using snap caps. A-Zoom makes some good snap caps. Thanks for watching!

@TADDs101 Жыл бұрын

@scrib_nibit174 Thanks for the prompt reply

@scrib_nibit Жыл бұрын

@@TADDs101 You are more than welcome. Enjoy your new Shield Plus.

@rapidrrobert4333 Жыл бұрын

#1, remove wood and glass. #2 spray thoroughly with brake cleaner be sure to get every nook. #3, blow dry with compressed air. #4 lubricate and put the stock back on. Seriously, I don't disassemble at all, just spray, blow, and lube.

@scrib_nibit Жыл бұрын

What ever works for you. This is more along the lines of a deep cleaning. .22LR are notoriously dirty. Thanks for watching.

@lawrenceswanberg8490 Жыл бұрын

Do magazines from an older Shield fit the EZ pistol?

@scrib_nibit Жыл бұрын

No. Older Shield magazines (1.0, 2.0) are completely different from the EZ magazines. Thanks for watching.

@Keith259 Жыл бұрын

Bought this same belt last year and still looks like new. One of my best purchases of 2022.

@jaybarr3307 Жыл бұрын

I find the hardest part is getting the bolt back over the charging handle during reassembly. The charging handle cocks slightly to a different angle, preventing the bolt from going over it. I noticed you had a camera cut there too. Gotta be a good trick for this out there...

@scrib_nibit Жыл бұрын

Ya, I did a cut scene. The trick is to get it lined up the first time. Sometimes you get it...other times you don't. The struggle is real.

@TXLoneStar_ Жыл бұрын

I have that exact black belt. Aces.

@gungadingo Жыл бұрын

That “Tab” is a swing link.

@scrib_nibit Жыл бұрын

Thanks for the heads up.

@jimmyleon2983 Жыл бұрын

The 10/22 can be a little tricky to disassemble and reassemble for cleaning. I've gotten excellent results in cleaning my 10/22 by just pulling back the bolt, locking it into position and scrubbing the bolt face, feeding ramp and entire loading breach area with a toothbrush, a smaller child's toothbrush works best, then wipe the area with a clean cloth and you're good to go. I've had my 10/22 for 20+ years and have never disassembled it for cleaning.

@scrib_nibit Жыл бұрын

Everyone has their own lil' techniques. Thanks for watching and sharing.

@Klaxet Жыл бұрын

I've read S&W M&P manual it says lubricate all internal and external parts....does it mean I should lubricate inside the barrel, just a thin layer? Thanks for the video.

@RanTausi Жыл бұрын

No.

@scrib_nibit Жыл бұрын

Page 31 of the manual discusses the 7 points of lubrication. You _can_ use clp on the inside of the barrel, but just make sure it's dry and clean afterwards.

@triggerman1092 Жыл бұрын

And whatever u do do not put lube in the striker channel. That needs to stay clean and dry

@neilstephens9330 Жыл бұрын

Mark 4 have the best breakdown 4 cleaning

@neilstephens9330 Жыл бұрын

Best boat Anker ever joke great learners pistol

@Professorbase Жыл бұрын

Hmm. Interesting mix of clp. I might try that.

@omfogg Жыл бұрын

Thanks for the vid! MKIV is my first 22LR and I was totally shocked how dirty it gets only after few hundred rounds. First time I cleaned it, I even disassembeled the whole trigger, cause it felt like there was sand stuck between moving parts.

@scrib_nibit Жыл бұрын

Glad I could help!

@kurleys Жыл бұрын

Straight to the point!! Great video!

@Jonathan906 Жыл бұрын

Helpful! Enjoyed this. You made everything clear. Looks straightforward. Thank you.

@scrib_nibit Жыл бұрын

Glad it helped. Thanks for watching.

@user-uc3rl3vf4v Жыл бұрын

Чудовий огляд

@scrib_nibit Жыл бұрын

Дякую за перегляд

@TXLoneStar_ Жыл бұрын

Ive actually seen some videos where the person would take a small hammer and tap out/tap in the slide stop pin (the bottom one). You took yours out like a boss.

@scrib_nibit Жыл бұрын

Not a very good idea. No hammer of any size needs to be used anywhere on a Glock. Thanks for watching!

@scrib_nibit Жыл бұрын

Yea, my hand was in front of the barrel of a perfectly clear gun. It's not something I would recommend doing on a daily basis.

@rongarcia7744 Жыл бұрын

Are all Ruger mark 4 Like this ,come apart easy to clean ?

@scrib_nibit Жыл бұрын

Yes sir! They all break down the same way. One button and done. Thanks for watching!

@erikhroso 2 ай бұрын

@@scrib_nibitmines not 1 button but that's by choice, I went with the tandemkross lower that screws in that stock lower felt cheap as hell 😂

@scrib_nibit Ай бұрын

@@erikhroso Good lowers, but the factory Ruger lower is far from "Cheap as hell."

@TXLoneStar_ Жыл бұрын

Subbed. I usually clean mine every 500 rounds so it's pretty dirty when I do get around to cleaning it. Clever idea with the "custom" toothbrush. Gonna steal that idea.

@scrib_nibit Жыл бұрын

Yeah, that .22 ammo is some dirty stuff. Thanks for watching!

Ең жақсы KZbin

Пікірлер