@@GeorgeThomann Awesome! Please subscribe

@@signedelacroix7213 Hmm if you haven’t changed any thing there is no other reason than a worn belt. You can check the pulley and see if it looks warped.

@@signedelacroix7213 Hard to tell on that one of the belt shows wearing you should change it

@@claudiorodriguezrodriguez Thank you please subscribe

@@gregsholly120 Ok sounds good I can help with the belt also may have a better price on that. I know we make them better. If you want send me your full model number to [email protected]

@@leebrown1317 Always glad to hear that!!! Don’t forget to subscribe Dave

@@naterowell1849 my pleasure thanks for viewing Don’t forget to subscribe Dave

@@signedelacroix7213 There are a lot of models on sole that have the same light resistance issue if it changes some from 1 to 20 maybe that’s what it is. You can try and adjust the steel cable that goes from the gear motor to the flywheel . Sometimes you can adjust the small holding nuts on the cable itself. It can help some

@@FitnessTechnologyServices I have a pedal that start to crack, do I have any chance with Epoxy 5 min?

@@becomingpeculiar2815 Well flashing display normally means display is bad. But I guess if gear motor is bad it could prompt the display to show motor errors

@ is there a way to tell if the gear Motor is bad?

@@becomingpeculiar2815 not if get the flashing signal right away . You could unhook the gear motor from the steel cable to see if it is a load issue

@@FitnessTechnologyServices ok we will try that. Thank you.

@@signedelacroix7213 The two center frame points have adjustable screw type levelers But I think the front and rear ones are fixed

@@sonia5874 Yes yes ...The better one will have a longer warranty

@@NatPaiva That’s probably a bad console signal. But it’s possible the incline sensor is bad remove it from incline motor and try cleaning it

@ I’ll try that. Thanks! It’s weird, because if i stop the workout, and I press the position I want to incline, it works as expected. 🫠🥲

@@NatPaiva Odd issues like that normally fall into a console problem

@@jademoon5103 I use super lube on the frame and sole lube on the wheel rails I carry both on my website Fitnesspartspro.com

@@signedelacroix7213 Not really I think the miles are displayed at the start up. After that make sure everything works fine. Stay away from anything under 2011 only because it’s hard to get parts

@@FitnessTechnologyServices I ujst bought a 2012. Another add had a sn 012 too E35 the same, but the control board different. How come?

@@falltron Hmm no count down normally is in the console the console should work as normal as far as the countdown goes then when countdown is done if there is a problem in the controller then it would trip breaker I would start with console

@@cingram8939 I hope you and your family have a happy new year . If your belt does not need a lot of adjustment then the belt guide are not needed but if you find you have to adjust it a lot then reinstall the guide. They do make a light noise!

@@albertguffanti8414 my pleasure

@ now all of a sudden I have a banging/knocking sound whenever I incline/decline. The noise stops after the incline/decline stops. No clue what’s happening.

I may have tightened the bolts too much! Loosening them a tad eliminates the noise

@@robertcornelisse8664 Hmm I’ve never been asked that question before I would think if it’s a household element everything should be normal

@@itstimboflex That normally means the controller got overheated due to walk belt wear

@@smittythecoach That is a bad controller that small light should be solid. I would also check your walk belt 90% of controllers over heat due to walk belt wear. See video testing sole walk belt

@@michaelotoole1807 no it’s not that’s probably a bad console

@@michaelotoole1807 I will have to post a picture of the new Nordic Track touch screen twice as big. And fails a lot 🤔

@@DarkSevariant Your unit probably has a link arm for the Resitance not a cable. But it has nothing to do with the incline if both are not working I would think it is the console. It could be the power board also

@@FitnessTechnologyServices hi, thanks for the reply...!!! ...hmmm, so you believe the console is bad? I took the console off, disconnected the three wire plugs, and removed it. Everything looked good. Also, any idea why when I look straight at the console the numbers are all blurred, but if I look down from the top, it's a perfect screen? Not enough power maybe? I's weird, it's almost like one of those screen covers for computers, where if you look from side, it is dark, but if you get in front of screen, you can see everything. There were three ribbon cables I removed, and cleaned with alcohol and put back. When you say power board, is that the board in the console, about 4 inches by 4 inches, or is there another one, down by the main wheel? I saw one video where the guy removed the shroud covering the wheel, and there was a circuit board about 6 to 8 inches square. I haven't disassembled it, but in my .pdf manual, I don't see a power board. Another thing, when I first got it, off Marketplace, and moved it into my home, I plugged it in, and heard a motor sound, but it only lasted like 3 seconds, and since I haven't heard anything, even though I unplug it when I'm done with my 'exercise.' The guy I bought it from said the resistance doesn't work, it's why I got a deal. Also yes, the incline ramp, which is below me when I exercise goes from 0% to 20%, and the ramp is stuck at 15%. It has never moved. I'll have to take off the shroud and see what's in there. I just got it a few days ago, and actually I run on it. I ran about an hour, ran 2.25 miles, and got a good sweat. It's a form of exercise, but very low low impact, since no resistance, but still better than nothing. So you're saying if resistance AND ramp aren't working, it may be the power board? I'll check for another board by the main wheel when I get the shroud cover off, but for now, the only board I have seen is the small 4 inch square one, inside the console. Thanks for replying..!!

@@DarkSevariant Well if it has a power incline it has to have a power board. The ones that don’t have a incline they use a 6vdc plug in type when both are having issues it got to be console or power board. IThink you will find a power board

@@Asmodeius Thank you. Try running the unit with no one on it. If it works fine. Most likely the overheating is from a worn walk belt making the motor work to hard

@@Asmodeius if you want send me your serial number to Fitnesspartspro@ gmail.com I can send you links for testing

@@drewhunter5277 My pleasure it is hard information to find???

@@BeanieandCecil Well if this is a touch screen they fail a lot if not try reversing the red and black wires on the incline motor itself sometimes when the controller fail they reverse 🔄

@@frankmanson3 Awesome! Glad to help

@@troym3219 I am good but thanks

@@troym3219 I have a different video replacing sole f/80 deck hopefully it is better. If you have any questions contact me at Fitnesspartspro@ gmail.com I have a few without back screen

@@bluesky0762 Always my pleasure... and you are welcome

@@dolphindancer68 On a Nordic Track try and see if is in metric units . If not the controller is bad. See my video called Nordic Track motor controller failure

@@lrr5425 I am always glad to help. Thank you

@@kenk1321 Awesome. Thanks!!!

@@murathp07 Well thank you..

My pleasure

@@AnthonyPCipolone keys have been out of business for some years. I would need your length and with. But sure ..If you have the original manual keys used to list it We also have a video on how to measure on our website. Fitnesspartspro.com under custom belt. Or email me at [email protected] and we will send you links

@@michaelotoole1807 Thank you

@@ryan0000e The first thing I can think is the speed sensor is shortened out ( or closed) try plugging it in and out to see if the controller is receiving signal

@ that makes sense. Thanks for you response!

@@damian_the_mando_apprentice for the ramp wheels I use only the factory stuff. On most other moving parts I use super lube synthetic grease it on our website

@@arturoguillen9949 Thank you. Try to recalibrate first if this is a touch screen model I don’t have the calibration but it is normally a gear ⚙️ icon

@@evan-kylelardinois2729 Hmm Ok try running in different areas on the deck. To see if maybe it has a worn area. Next you may have to remove the side rails and tighten the deck mounts (wipe the machine down and tighten the belt for a squeak how weak of a repair was that) let me know what you find. I have videos on replacing the belt which will show you how to remove side rails hope this helps Dave

@@FitnessTechnologyServices Ok, thanks for the tips. Apologies late reply. I took off the side step plates. Nothing seemed loose but there was some rust on the front left screws so I greased that with spray. My wife ran 6 miles last night and it still squeaked. She ran in different spots. Towards the front it squeaks. If she runs behind the side safety arms it does not. The belt does not feel smooth underneath but I'm not an expert on that. I might check regreasing the pivot bolts again. I am still thinking its the belt though.

@@evan-kylelardinois2729 Ok I have seen times were there is a worn area on the deck making noise. Send me a video to my email Fitnesspartspro@ gmail. com I will see if I can help better

@@EricTalbert-m6f Thank you! This sounds like a console or at least the console display send me your serial number to [email protected] if you need me to check on parts