RMS

Пікірлер

@johngulliksen514 9 күн бұрын

It's pretty obvious this individual has next to 0 experience in front end alignment. When you change these bushings the vehicle needs to be on an alignment rack like the ones I've used for 42 years . The degree numbers on bushings is how much the bushings will change caster or camber not how much caster or camber already has. You must first get alignment readings on a alignment computer to determine what size bushings are needed to keep camber at about .25 degrees for optimum tire wear and increase caster as high as possible as well. Sorry for the book 😊

@rms2048 9 күн бұрын

Thank you for the input , there definitely are quite a few people having issues with death wobble in the fords . This did work for me but clearly you should have a shop set up your front end no argument there .

@SOULJALOS 21 күн бұрын

Question, working in a Thermador range top…my burners show no gradual increase & decrease from low to high and vice versa. If the unit hasn’t been properly converted, would that affect my burners? In this case how I explained above. It’s almost like I only have either a high flame or a low flame. Hope that makes sense and I appreciate any help, thank you

@rms2048 18 күн бұрын

It’s a possibility it was not converted correctly . Propane orifices are smaller but also vary per burner size . Also the regulator needs to be converted as well … these both should be checked if it’s in question .

@SOULJALOS 18 күн бұрын

@ thank you sir

@markcavandish1295 25 күн бұрын

That looks like a project I’m not qualified for

@mick5740 4 ай бұрын

Our Beckett / Coleman. Has stopped working right. Been stuck in lockout. I finally took a closer look and noticed the screw / nipple in the clean out was leaking small amount. I loosened and tightened and think it stopped. Wondering how am I supposed to clean out the clean out hahah. Also wondering why it’s doing this ? Any advice appreciated

@rms2048 18 күн бұрын

The cleanouts toward the outside of the unit not directly above burner need to be vacuumed out with a soot vac … this is hvac territory usually not homeowner stuff

@YoungOzzy432 6 ай бұрын

What degrees bushing did u use ?

@yosoyjesus8943 6 ай бұрын

IF THE WIRE IS 12 /2 ON A 15 AMP BREAKER AND IS WORKING FOR LIGHTS ONLY AND THERES ONLY 8 TO 10 LIGHTS CONECTED TO THAT BREAKER WITH OUT SERVICING ANYTHING ELSE THERE'S NO FIRE HAZARD GET REAL

@rms2048 6 ай бұрын

Receptacles on circuits this is not the only room . Air conditioning units in windows are big draws . These are the facts .

@dennywires 6 ай бұрын

That looks like old 12 nm before the yellow jacket

@rms2048 6 ай бұрын

Looks the same as 14nm back then but you can tell how easy it flexes and the strippers don’t lie either

@highvoltage1979 6 ай бұрын

Why pull new wire, just put it on a 15 amp breaker

@rms2048 6 ай бұрын

As per national electric code you cannot downsize wire in a circuit , the next electrician may put a bigger breaker on if he sees the larger wire in panel

@rvadventures 7 ай бұрын

Yeah my 2016 dually just started this after we replaced the drag link and inn/outer tie rods and sway bar end links and front end alignment. Just wondering what it could be. Didn’t have the issue b4 all this was recommended

@rms2048 7 ай бұрын

Ford sets these really close can’t hurt to add a few degrees to stabilize. Things move after 100k too . Mines going well still but it will change alignment

@jamesbieniek8290 9 ай бұрын

What about the post in the corner.

@rms2048 9 ай бұрын

The GC is addressing it ….

@alstagl1221 9 ай бұрын

What about when the romex runs through insulation? It cant shed heat in that situation.

@rms2048 9 ай бұрын

The national Electric fire code book states that cable can be run though conduit though walls to protect it . The amp rating is not affected if following code specs

@omarimchenry9153 9 ай бұрын

yeah but it sucks for the next plumber who comes out to replace somethint

@rms2048 9 ай бұрын

I mean a plastic tub drain on a fiberglass tub should be there for a while like forever almost . I’m not against plumbers putty if done correctly. But silicone is less call backs for glass tubs

@setoman1 9 ай бұрын

Eehhh, it’s fine.

@rms2048 9 ай бұрын

I mean as long as you de rate the breaker sure

@Jakaro007 10 ай бұрын

Same thing happened to mine.

@Jakaro007 10 ай бұрын

They are sending me a new light after filing a warranty claim. Fyi.

@rms2048 9 ай бұрын

They did refund me but I wound up with the arkflex This time

@topmodstv3682 10 ай бұрын

These bushings are great for destroying axle dust seals and inner oil seals

@bkearns8 11 ай бұрын

Same exact thing happened to my arkfeld pro. I came here to see if others had the same issue before looking for warranty service, thanks for posting the video!

@rms2048 6 ай бұрын

You’re welcome I did wind up getting the flex and another pro . I should do another video about the lockout

@pmczapczara5332 Жыл бұрын

Those inserts are not the amount of caster or camber it has. They provide up to 2 degrees of change depending on how oriented and how much offset different ones provide by moving the upper ball joint geometry. Base caster and camber are based on the front end design. These trucks once had fully threaded bolts, instead of shouldered bolts, that held the track bar to the frame. This resulted in the track bar bracket getting loose at the frame. Your shocks look very old. Take the easy end loose compress it and see if the hydraulics are wore out.

@rms2048 Жыл бұрын

Shocks were done previously with all front end tie rods etc just has some undercoating on them is all cheers

@flashclimber Жыл бұрын

Did it work?

@rms2048 9 ай бұрын

Yes

@YoungOzzy432 6 ай бұрын

What degrees did you use ?

@DumbCarGuy 5 ай бұрын

@@YoungOzzy432 secret stuff

@WarVet1984 Жыл бұрын

Hey brother did that work for you? I have replaced a lot of things and still have the shacking

@rms2048 Жыл бұрын

This did work for me , I have not had a death wobble since . But this was basically the last thing that could get replaced in the front end ….

@WarVet1984 Жыл бұрын

@rms2048 thanks for the reply, my issue was the steering damper was defective, i replaced it and its perfect now

@john4kc Жыл бұрын

Step away from the spray paint.

@walkermom100 Жыл бұрын

We hired an electrician to set up our plug and panel for this. Works great. You can tell when elec is back on if main box is reading numbers. The panel was altered with a safety switch so the main breaker can't be engaged when in use for generator. Although running almost entire house is expensive it is a trade off for convenience and having heat in the cold. Michigan loses power a lot. Dte. So we felt it was a good investment.

@rms2048 Жыл бұрын

Thats great , there are a lot of options for generator installations. Some of that stuff will be in another video. In my opinion it is a great investment for a homeowner. If you have natural gas generator thats a great option but anything is cheaper than a frozen home .

@walkermom100 Жыл бұрын

@@rms2048 we upgraded the generator to a 13000 watt dual fuel. Agree. Look forward to your other posts.

@rms2048 Жыл бұрын

Thank you ! If you have something particular your interested in let me know .

@walkermom100 Жыл бұрын

@@rms2048 actually I'm having a difficult time finding videos on a way to extend a bathroom vanity light out from the wall do it will hang over a medicine cabinet I have that sticks out about 3-4 inches. We cant recess the cabinet since it's on an outer wall. My only solution is to point the lights up.

@rms2048 Жыл бұрын

Check out vanity light clearance

@CarlMillerstore Жыл бұрын

The longest running one I have is 20 years on my water heater.. held up so far..

@rms2048 Жыл бұрын

I have had success with them , but also had a handful fail .

@StormyGlide Жыл бұрын

FYI, the video displays sideways. Even on my iPad, if I tip it to one side, the display is all wrong.

@rms2048 Жыл бұрын

Working on it camera setting

Ең жақсы KZbin

Пікірлер