With the price of the tool, it is not better to buy another water hose? 😅

Do I have to wear polarized glasses? 😂

Can you use copper wire too?

Here is my Amazon link and thanks for the support ❤️ CLT01 4 3/4 inch Stainless Steel Tool: amzn.to/3Cq69So Lock Wire, T302/304 Stainless: amzn.to/4hz3MvD

Thanks again. Very helpful ✌️

Thanks for your practical explanation. Helps a lot 🙏🏽

Thanks for the support and here is my Amazon affiliate links: 3M PPS (Original Series):------ amzn.to/40KYiIh Spray Gun Cup Adapter: ------ amzn.to/4h7U4As Cup Lids and Liners Kit :------ amzn.to/3Cp0JXW Fuji Spray 5431-2Qt Pressure Pot: ------ amzn.to/3PPb9TO Fuji Spray 2895-T75G Q5: ------ amzn.to/4jwUty4 Fuji Spray 2049F 6-Foot Flexible Whip :------ amzn.to/4avxuiK

Thanks for the support and here is my Amazon affiliate links: ARANA 7 Inch Gas Strut Props 7" :------ amzn.to/42rYFZy DecoBasics Full Overlay Soft Close Cabinet Hinges:------ amzn.to/3WzIaal Framing Square fence:------ amzn.to/4g8aTK5 Milwaukee framing square :------ amzn.to/3PMRHaj

Here is my Amazon Links: Thanks for the support 📦✈ DecoBasics Full Overlay Soft Close Cabinet Hinges:------ amzn.to/3WzIaal DecoBasics Half Overlay Soft Close Cabinet:------ amzn.to/3CoQVgm Framing Square fence:------ amzn.to/4g8aTK5 Milwaukee framing square :------ amzn.to/3PMRHaj Milwaukee 48-22-6625 25' :------ amzn.to/4azTDfW Milescraft 3406 GrabberPRO:------ amzn.to/42rNwYM Kreg ACS Plunge-Cut Track:------ amzn.to/3Co9Nft Kreg KMA3225 Shelf-Pin Jig 1/4" :----- amzn.to/3WBAqo7 Kreg KHI-Hinge Concealed Hinge Jig: ------ amzn.to/3E6fFL5 IRWIN QUICK-GRIP Bar Clamp:----- amzn.to/4gfHoX1

I have both

Great job 👏🏻

Thanks for sharing some good tips. The lockers turned out real nice, very sharp build!

The design has changed a bit I think.. mine doesn't have ground wire. I just took mine all apart just like this video and put it back together. I wanted to clean it and took out the wrong screw, nuts fell down inside the unit and my only option was to rip it apart , clean, put back together. Took forever! I paused this video in a ton of places for help. Wish it was a little slower but pausing worked fine. I can't complain, I'm super appreciative of you uploading this! I am never tearing it apart to clean it again LOL

Thank you very much

Thank you for the video. My heater is back up and running again.

Unbelievable!

Love my MFT. Especially with a track clamp, phenolic resin top. Planning to buy a 2nd. When I bought it, before my table saw, I became frustrated with it. But once i got my table saw, i allowed the mft to do what it’s good at, rather than try to do absolutely everything with the track saw and MFT. And now, it’s indispensable

Very helpful video, greatly appreciated!

Where did you get the pressure pot

Good info, mine had that secret screw. Thanks Brother!

So I suspected broken brush belt as well but that was not the case. Thought it was the switch but cut that out and completed that circuit to make it always on and that didn’t work. Perhaps the motor? Also the little light on the pcb isn’t coming on either… any thoughts?

Thanks dude. You are the MAN!!!!!!

Nice video. I got the mft because i moved into a 200 square foot shop and my tablesaw would not fit. I am just learnimg how to use this system, so thanks for the heads up on the purchases i am going to need to make.

I need to find out how to remove the digital panel in the front.

Hi. I have a 2019 Summit. Which one is the correct model for the Air Suspension Elbow Repair Kit?

Well done sir. Thank you!

I love this video. But my checking account hates it.

I’ve got an E2 error. I only took out the piece near the fan @1:00 to clean it

I have 4 of these doing this now. This is genius

Great fix music sucks

Do you know if the ninja multicooker foodi lid can be removed so i can travel it in lagguage

Do you know why mine just won’t turn on at all? I was in the middle of air frying wings and it just completely shut down on me won’t turn on at all

This video came out a while ago but I have a question still. When you are putting it all back together, how do you arrange the springs so that the whole thing can close up properly? Mine came out of place and I can’t figure out how to get them back.

Super helpful thank you!!

Rex, I got a shark navigator, and my on and off switch burned out. I replaced it, and the suction now works, but the brush didn't. Then I inverted the cables, so the brush works, but the suction function is not working now.

Thanks for your opinion! It helps deciding, because I am looking for a setup like that.

This help me a lot thank you

Why you raise the car ?

Love the packout stuff “pretty much the best tool boxes, pretty much” 😅

Mine is very low will this cause the 40amp fuse to blow

Thanks for this vid mate it came in real handy, I ended up using some high density foam from a weights mat and it worked perfect, it's actually springier and smoother that that silly little piece of red plastic it replaced lol ..cheers!

Can I use a gun I already have in my collection with the Q5 system?

2 drawers, 3 drawers or 4 drawers? Bery confusing

big red China fan boy, all the plastic wont last 20 years

Thank you! My mistake was trying to reassemble it upside-down instead of the way you did it.

Thanks for this video. However, my unit will not close completely. Any ideas?

Amazing video, I could watch this all day!

$199 MSRP for the 4 drawers, seems to be pretty friking expensive $128 that you paid should be the MSRP price! 😅

Looks like the design still is the same and nothing has changed, beside been 4 drawers design

This video was super helpful and helped my fix the switch for my ninja foodi AG302