C'est possible qu'elle ne mette pas ses mains devant merci !
@sylviahoy78213 күн бұрын
The music is very distracting and annoying. This video would have been much more helpful with audible explanations.
@sylviahoy78213 күн бұрын
So
@lesliefatout473117 күн бұрын
The video does not show clearly for the chain looper thread how to thread the second guide after the tension discs. Please provide more detail.
@Mybernette13 күн бұрын
Dear @lesliefatout4731 Thanks for your inquiry. The first guide after the tension is to be threaded from right to left, the second one from front to back, that is shown at time code 1:01. There is no other threading possible for these two purple guides. The third guide is threaded from top right to left, the fourth from bottom right to left. The wire with its spring inside is threaded from right to left. This is all a bit tricky to show, as the inside is quite tight. But we trust that together with the threading diagram and the instruction manual, you will manage correct threading. And never forget, practice makes perfect. With this we wish you many hours of pleasurable sewing with your bernette 48/42. Kind regards
@lesliefatout473113 күн бұрын
Thank you. That threading detail is very helpful!
@kamuz26eafo23 күн бұрын
a total disappointment, it had been bought to make lingerie, the teeth did not have strength, I just put a little fabric on top of another and took it out to the side, it was sent to technical service and they made thousands of excuses, on the subject and they never acknowledged that their The product came out bad from the factory, I don't know what Bernette's policy is, never admitting that a product came out defective, I say this because at the same time we bought an overlock from another brand at a lower price and it does the job without problems, what could you tell me about it?
@elizabethmnisi8045Ай бұрын
I'm in SA , and I need this machine at a best price where can I buy it.
@Mybernette27 күн бұрын
Hi @elizabethmnisi8045, when looking for a dealer, please visit the website www.mybernette.com/store-locator. We wish you lots of fun with your machine!
@mariebambo589Ай бұрын
Does not show the intricate threading
@Mybernette14 күн бұрын
Dear mariebambo589. Thanks for your feedback. Yes, the video tutorial 14/15, b48 basics of combo stitches does not show the threading of the b48. For threading the b48, please refer to the corresponding videos in the playlist, either on bernette.com or on youtube.com, such as: Overlocke threading, re-threading, coverstitch/chainstitch threading and so on. Find all videos linked here: www.bernette.com/en-US/models/bernette-48-funlock We trust this brings you further in learning about your b48 and having fun with it seewing your projects.
@sharonschmidt6464Ай бұрын
Can you tell me the mm of the leather you used? Thank you!
@MybernetteАй бұрын
Hi @sharonschmidt6464, we used a leather that is about 2mm thick and rather soft. If you use a stiffer leather, this can also be a little thinner.
@SandraMartin-yz8ciАй бұрын
Just purchased the B64. I am so very disappointed in the video tutorials, words would be much more helpful than pointing. The instruction booklet included in the box is no help either.
@MybernetteАй бұрын
Hi @SandraMartin-yz8ci Thank you for your feedback! We're sorry to hear that the tutorials and instruction booklet didn’t meet your expectations. Could you let us know which specific areas or steps you found unclear? We’d love to help you further and ensure you get the most out of your B64.
@elbantiАй бұрын
Janome HD9 twin!
@serapselcukyilmazАй бұрын
Araçları çıkarmaya ne gerek vardı.çıkarmadan da ya😊😊😊ğlanabilirdi
@EkiwwaNoelАй бұрын
Why this machine looks like a janome hd9? Is this a rebadge janome. I know pfaff used to make bernettes.
@janegirl33Ай бұрын
What is the heaviest weight thread that can be used with this machine?
@Mybernette26 күн бұрын
Dear @janegirl33, the heaviest weight thread that can be used is Polyester #20.
@janegirl33Ай бұрын
What is the maximum needle size that can be used on this machine?
@Mybernette26 күн бұрын
Dear @janegirl33, needles up to 110 work.
@HeroJutt-j8xАй бұрын
Thnks
@sharonkhor7433Ай бұрын
Hey I know I’m looking at the 8 years old video 😅 I wanted to get second hand 340, just wondering if the cds can be used on my imac now?
@MybernetteАй бұрын
Hi @sharonkhor7433! It is important to know that our software doesn’t run on Mac unless a Windows Operating system is installed. There are two ways to do that, depending on whether you have an M-chip or another Intel chip Mac. On an Intel Mac it has bootcamp (software for creating virtual machines with Windows) on it for free. But you have to buy a windows operating system and could try to install the software. With M-chip Macs (the newer ones) you would need the paid (annual cost) Parallels software (software for creating virtual machines with Windows) and you can only install Windows 11. At that time we tested the Customizer software on Windows 7 and 8.1 but not on the newer versions and we can’t guarantee that it will work. And we are sorry that we don’t offer support for this product anymore.
@sharonkhor7433Ай бұрын
@@Mybernette thanks for your reply, message noted
@mrsbrzmariaАй бұрын
For some time I must use machine whell to start it, which very annoying, because I need 2 hands for sewing. Almost all the time, I stop , I must move manually whell again and again. What may cause this ? Im using my bernette almost everyday, its fantastic serger, but for some time now, I must start it manually. Any help ?
@MybernetteАй бұрын
Dear @mrsbrzmaria. Thanks for your comment. There seems to be a technical issue, and it is hard to judge without seeing the machine. Please contact your authorized local bernette dealer for support. Thank you.
@mrsbrzmariaАй бұрын
@@Mybernette I already found , what caused this problem. DEtailed cleaning under needle plate , fixed this error. Now it works like new again. I love this serger. Thank you for your reply
@MybernetteАй бұрын
@@mrsbrzmaria We're happy to hear it and wish you lots of amazing projects with your serger! 😍
@KaIero2 ай бұрын
1:07 muss ich die platte jedes mal tauschen ? wenn ich vom nähen zum sticken Wechsel
@MybernetteАй бұрын
Hallo @Kalero ja, es wird empfohlen, die Schichtplatte zum Sticken zu wechseln. Das kleinere Stichloch verhilft zu einem schöneren Stichbild der Stickerei.
@KaIeroАй бұрын
@@Mybernette hallo, danke schön fürs antworten, der Clip ha ja schon paar tage hinter sich :D Super, gut zu wissen... Macht es mir dann nicht leichter obs jetzt eine 79 wird oder doch 77&70
@MybernetteАй бұрын
@@KaIero Die b79 ist natürlich eine Kombo-Maschine, die Sticken und Nähen vereint. So hat man eine Maschine, die beides kann. Das bedeutet aber auch, dass man gewisse Einstellungen wie z.B. das Wechseln der Stichplatte vornehmen muss. Kauft man die b77 und b70, entfällt dies natürlich, weil jede Maschine auf Nähen bzw. Sticken ausgerichtet ist. Falls man sehr viel näht und stickt (und auch immer abwechselnd), dann ist es natürlich von Vorteil, wenn man zwei separate Maschinen hat. Liebe Grüsse von deinem bernette Team 😊
@codelinx2 ай бұрын
Wish there was audio 🫠
@MybernetteАй бұрын
Hi @codelinx thanks for your feedack! Did you discover that you can also follow along using the transcript (enabling captions)?
@sybilreid6932 ай бұрын
These videos are not helpful at all
@MybernetteАй бұрын
Hi @sybilreid693 we always give our best to provide helpful content, what information in this tutorial were you missing?
@BentAlsultan2 ай бұрын
i bought it last year , its the worst embroidery machine , i had janome mc 500 its waaay better than this machine , have a lot of embroidery problems , and its too expinsive , i dont advise any body to buy it!!
@MybernetteАй бұрын
Hi @BentAlsultan We’re sorry to hear that you’re not satisfied with your machine. We encourage you to reach out to your bernette dealer for assistance with any issues you’re experiencing-they can provide valuable help and tips. We’ve had so many customers over the years who have been very happy with the embroidery features of this machine, and we hope you can also achieve great results with it.
@BentAlsultan2 ай бұрын
i bought it last year , its the worst embroidery machine , i had janome mc 500 its waaay better than this machine , have a lot of embroidery problems , and its too expinsive , i dont advise any body to buy it!!
@MybernetteАй бұрын
Hi @BentAlsultan We’re sorry to hear that you’re not satisfied with your machine. We encourage you to reach out to your bernette dealer for assistance with any issues you’re experiencing-they can provide valuable help and tips. We’ve had so many customers over the years who have been very happy with the embroidery features of this machine, and we hope you can also achieve great results with it.
@Dave00_2 ай бұрын
Cant express enough how much i just HATE that the bobbin will never be picked up😊 ive done everything correctly yet it still refuses to be picked up by the thread. And if something messes up while sewing its literally ALWAYS the bobbin. This machines technique is the worst thank you❤️
@trishy99442 ай бұрын
I can’t find any info or help with the bottom bobbin not catching.
@Mybernette2 ай бұрын
Dear @trishy9944 Thank you for reaching out! To better assist you with the issue of the bottom bobbin not catching, could you please provide a bit more details? Let us know the specific machine model you’re using and any troubleshooting steps you’ve already tried.
@lynnleipold26172 ай бұрын
Thank you for all the great tutorials to help me use my serger that I just got yesterday
@VIProach2 ай бұрын
Is sew and go 5sold in Italy?
@Mybernette2 ай бұрын
Dear @VIProach for more information & availability details please contact your local dealer in Italy: www.bernette.com/dealersearch
@gaellelc16352 ай бұрын
Thank you so much! I was about to give after some unsuccessful tries. Thanks to your tutorial, I have succeeded at last!!! 😅
@perrier4403 ай бұрын
Je vais bientôt m'en procurer une !!!
@SlightlyOverripeAvocado3 ай бұрын
Great video! The finished strap looks great too! Thanks for this. Just what I needed to get going making my own as a birthday present for a friend.
@kerrieparker63673 ай бұрын
I don't understand still what the balance dial is for. Would love more explanation. Thanks!
@Mybernette3 ай бұрын
Dear @kerrieparker6367, the balance helps to adjust the stitch pattern when the sewing result doesn’t look regularly, depending on the used fabric, thread etc. When you sew the honeycomb stitch (S1, Stitch C) for example and the stitch is too loose so that the corners do not touch, you can use the balance to correct it. Of course it will also work the other way round when the stitch is sewn to tight so that it is overlapping. Another application is for example, when the two beads of the buttonhole are sewn differently.
@choccooco3 ай бұрын
this is so cool :O i want to buy a 3'' guitar strap but most of them are way more expensive than 2'' so your tut helps me a lottt
@Arlenedesigner3 ай бұрын
How I make bias with b42? Any video showing it regards
@Mybernette3 ай бұрын
Hi @Arlenedesigner. Thanks for your inquiry. On www.bernette.com there is no instruction for bindings with the b42. To make a bias binding with the b42 you can either sew the binding in two steps, by stitching your bias tape onto or under the edge, fold it around the edge and topstitch it, using a coverstitch or a chainstitch of your preference. Or you can use the BERNINA binder C21 for a double fold binding or C22 for a single fold binding (both accessories require to have the accessories holder). How that works in detail can be found on www.bernina.com under the respective binding accessory. With this we wish you fun and pleasure stitching with your bernette 42.
@martineleroux57473 ай бұрын
Traduire en français
@dmitrijmoreinis8213 ай бұрын
Was ich gut fand, dass so wie im Video gezeigt wird, die Maschine nicht den Unterfaden hochgeholt hätte! Der Unterfaden wurde einfachmal von Spulenabdeckung eingeklemmt. Und das BESTE! Die Maschine wurde vorher ausgemacht! Ausgemacht! Da ist nichts mit Tasten drücken!
@moialicze3 ай бұрын
the most important information is not shown! 1:10 - how am I supposed to unscrew the further screw with the screwdriver attached?!
@Mybernette3 ай бұрын
Dear @moialicze thanks for your comment and for spotting that detail at 1:10. The screwdriver shown in the video has been packed with the first 100 machines supplied, and with our machine for filming. However, following machines have been equipped with a shorter, triangle style screwdriver that allows to unscrew/tighten the screw at the rear of the stitch plate comfortably. Should you be one of those, having a very early machine, please contact your authorized bernette dealer for a suitable screwdriver. We trust with your maintenance and care you will have many pleasurable sewing hours with your bernette.
@rosefarquhar10753 ай бұрын
I have the same problem. As this video was made 7 years ago, and I bought my machine less than 2 years ago, I’m disturbed to find that I might have been sold a very old machine that has been sitting around at the dealers for at least 5 years!
@rosefarquhar10753 ай бұрын
@@Mybernette I have the same problem. As this video was made 7 years ago, and I bought my machine less than 2 years ago, I’m disturbed to find that I might have been sold a very old machine that has been sitting around at the dealers for at least 5 years!
@Mybernette3 ай бұрын
Dear @@rosefarquhar1075 you mean the screwdriver shown in the video? It has been packed with the first 100 machines supplied, and with our machine for filming. However, following machines have been equipped with a shorter, triangle style screwdriver that allows to unscrew/tighten the screw at the rear of the stitch plate comfortably. Should you be one of those, having one of the early machines, please contact your authorized bernette dealer for a suitable screwdriver. We trust with your maintenance and care you will have many pleasurable sewing hours with your bernette.
@w.g.gerberink84504 ай бұрын
Nederlandse spraak
@jf83574 ай бұрын
The shape looks exactly like Janome straight stitcher. Is it a rebrand?
@audenhealey26434 ай бұрын
I have the same question - is this the Janome HD9?
@Mybernette3 ай бұрын
Dear @jf8357 and @audenhealey2643, the bernette 08 Straight Stitch machine is the new sewing machine from bernette with a unique package of features such as its Swiss Design and accessories. The b08 Straight Stich comes with the super spacious extension table (23.6” x 15.7”, 60 x 40 cm) which gives all the room needed to spread out. Additionally, bernette offers two customer oriented and carefully selected presser feet sets for the b08 Straight Stitch machine. Other optional accessories are available. With all that, the b08 differs from other Straight Stitch machines in the market. bernette is part of the BERNINA Textile Group. The entire process from product specification to production is controlled by our headquarter in Steckborn, Switzerland, to ensure high quality. The distribution of bernette products via the BERNINA sales network guarantees an extraordinary service in support and maintenance.
@feeseize95692 ай бұрын
@@Mybernette That wasn't a "no"
@elbantiАй бұрын
Undeniably same as Janome HD9 but in Bernie costume.
@pe_pfi4 ай бұрын
Can't wait for this machine
@PatchworkPirate4 ай бұрын
I know that dinosaur pattern! Also happy to see bernette has joined the 1600 spm gang. I have a similar machine (exact same setup), and it's a beast. This is a great option for apparel sewists, quilters, cosplayers, and bag makers alike!
@JoshBombFiberArts4 ай бұрын
If y'all feel like sending me one to review, I would greatly appreciate it! :)
@patcook12804 ай бұрын
Missouri star is using it on their you tube work. Try to see if you have authorized dealer in your area for maintenance.
@Mybernette3 ай бұрын
Hi @patcook1280, if you are looking for a vendor, please visit the website www.mybernette.com/store-locator.
@nanalougoesoutside91944 ай бұрын
Love it!! Also love #QuilToni and her pixel quilts!! 🎉🎉🎉
@PatchworkPirate4 ай бұрын
I spotted Toni's pattern immediately. Love it!
@JoshBombFiberArts4 ай бұрын
What's the USA MSRP? I am literally in the market for a straight stitch machine. This could not have come out at a better time!
@emilyjohnston87034 ай бұрын
AllBrands has it listed for 1,999. Unsure if that includes the auto thread cutter foot pedal. Have one on my Juki and love it, but miss the needle up/down setting and foot pedal up/down control.
@PatchworkPirate4 ай бұрын
MSRP $2,499 USD, most places are taking pre-orders for $1,999.
@Mybernette3 ай бұрын
Dear @JoshBombFiberArts, we're thrilled to hear that you're excited about the new bernette 08! We know you'll have amazing times sewing with it. For pricing details, please reach out to your local dealer in the autumn for all the information.
@ramyasinchana85634 ай бұрын
Superb
@melaniedelaurell4 ай бұрын
i have this machine and aside from the silly music that just annoys you to oblviion this is a lovely machine good value I picked it because it can go slow and fast and not just one speed ive got to know all the settings by the book and practicing not by these silly tutorials which annoy you with the music. sorry bernette but whomever chose to put this music on here.
@KonstantinSchuckmann4 ай бұрын
What type of screws are required for the bernette b48: I lost my screws and need some replacement
@Mybernette3 ай бұрын
Dear Konstantin, thanks for your inquiry. Please contact your authorized bernette dealer for replacement screws, because with same diameter, there are different length screws available, and you may want to make sure to avoid thread damage in front of the needle holder.
@34lyndy4 ай бұрын
Ireally like my YaYa Han. Works very much like a Bernina.
@vladimirmach61454 ай бұрын
The Bernette b05 Academy is the best sewing machine on today's market. What?? Seriously?? Yes! Let's cut to the chase. I wanted an excellent sewing machine to do a good job for me for the rest of my life, so I followed the brand reputation first and bought a JUKI HZL G220. What a horrible plastic piece of Chinese junk! Sluggish, the electronic system lags like on the dead bed, every response to pushing the pedal being considerably delayed. This JUKI HZL H220 actually turned out to be the worst sewing machine I'd ever tried. The quality is terrible, the machine lacks manual foot pressure regulation, and it doesn't even have any socket and pin for the second thread spool to use a twin needle! Moreover, the product stopped working after only three hours of regular use. Plastic, plastic, plastic. So I returned that piece of crap. I expected good sewing machines to be on a more expensive side, so I bought a Janome Skyline S5. Not a good choice, the motor was remarkably weak (50 Watts only), and the feed dogs did not work well enough for the price. So I returned it, too. Then I bought a Bernette B77. Not a bad machine, the feeding works really well and all the necessary functions are available. But the use is really uncomfortable: to apply any basic adjustment (e.g. the upper thread tension), you must struggle through the computer menu on the display, rather than simply adjusting a dedicated dial directly. Everything is computerized, even the pressure foot lift is electronic and lacks the standard mechanical lever, which sucks. So finally I came to the conclusion that these "modern" electronic/computerized machines are not worth my patience at all: they offer hundreds of stitches that no one will ever need, but the basic functions are uncomfortable to reach for. So I returned it. At last, I decided to return to the good old mechanical system and got searching for the best choice among mechanical machines. Having gone thru tens of various offers and read tons of information, I finally decided to take up the Bernette B05 Academy. Bingo! I hit the bull's eye! The machines has EVERYTHING and even more, it's sturdy, super strong, extraordinarily fast, and the control is based on standard of directly adjusting the mechanical dials. The quality of stitches is amazing, and even the price is a piece of cake. So I finally decided to buy two, and I'm really happy.
@Mybernette4 ай бұрын
Thank you very much for your wonderful feedback! We are thrilled to hear about your outstanding experience and wish you many great times sewing!
@vladimirmach61455 ай бұрын
The Bernette b05 Academy is the best sewing machine on today's market. What?? Seriously?? Yes! Let's cut to the chase. I wanted an excellent sewing machine to do a good job for me for the rest of my life, so I followed the brand reputation first and bought a JUKI HZL G220. What a horrible plastic piece of Chinese junk! Sluggish, the electronic system lags like on the dead bed, every response to pushing the pedal being considerably delayed. This JUKI HZL H220 actually turned out to be the worst sewing machine I'd ever tried. The quality is terrible, the machine lacks manual foot pressure regulation, and it doesn't even have any socket and pin for the second thread spool to use a twin needle! Moreover, the product stopped working after only three hours of regular use. Plastic, plastic, plastic. So I returned that piece of crap. I expected good sewing machines to be on a more expensive side, so I bought a Janome Skyline S5. Not a good choice, the motor was remarkably weak (50 Watts only), and the feed dogs did not work well enough for the price. So I returned it, too. Then I bought a Bernette B77. Not a bad machine, the feeding works really well and all the necessary functions are available. But the use is really uncomfortable: to apply any basic adjustment (e.g. the upper thread tension), you must struggle through the computer menu on the display, rather than simply adjusting a dedicated dial directly. Everything is computerized, even the pressure foot lift is electronic and lacks the standard mechanical lever, which sucks. So finally I came to the conclusion that these "modern" electronic/computerized machines are not worth my patience at all: they offer hundreds of stitches that no one will ever need, but the basic functions are uncomfortable to reach for. So I returned it. At last, I decided to return to the good old mechanical system and got searching for the best choice among mechanical machines. Having gone thru tens of various offers and read tons of information, I finally decided to take up the Bernette B05 Academy. Bingo! I hit the bull's eye! The machines has EVERYTHING and even more, it's sturdy, super strong, extraordinarily fast, and the control is based on standard of directly adjusting the mechanical dials. The quality of stitches is amazing, and even the price is a piece of cake. So I finally decided to buy two, and I'm really happy.
@Mybernette4 ай бұрын
Thank you very much for your wonderful feedback! We are thrilled to hear about your outstanding experience and wish you many great times sewing!
@vladimirmach61455 ай бұрын
Just another video ruined by a disgusting musac instead of nice and natural spoken commentary.