can i still solder without flux?

Yeah.

What are those cases named? That ailexpress link doesn't work now

can I use arduino as ISP for the attiny10 with avrdude?

Open it up and show the pcb layout. This model is supposedly gear towards professionals.

ya?

yeah yeah yeah yeah

572°F - 662°F or 300°C - 350°C convert °C to °F 300°C multiply by 1.8 + 32 = 572°F convert °F to °C 662°F - 32 = 630 divide by 1.8 = 350°C

Excellent video! Could you please advise me how to start the board with the Hall sensor? Thank you very much.

Thanks a lot! I almost gave on my 12 years old laptop, with random freezes / blue screens and idle temps of 85 - 90 degrees... Then, I found your video and decided to give it a try... 2 hours later ( I really took my time because it's the first laptop I've ever opened), it was back from the deads. Idle cpu temps of 55 degrees, 60 degrees while browsing and other light activities! Next steps: battery and windows 11!

This is the most valuable info on soldering...practical and you can see the result

You are a legend! Thank you for sharing.

Typical Chinese move... Hard work is highly regarded, even if it means BS. Dishonesty doesn't matter to them.

This isn't a review. This covers roughly how it works though! Which is to say if you start it in the cradle, it'll go through temperature and airspeed (F01-F99 I suppose,) tapping setting once picks a temperature and twice an airspeed; the trash manual talks about hitting setting 3-4 times...why? And holding Setting 4 times gets you instant off which you should never do instead of just using the cradle and letting it slowly back to 100 degrees C then slowly shut down and turn off. (Drawing it off the cradle bringing it instantly to life, so don't feel too safe until you unplug the thing.) Anyone got more comments about using it and not melting your suction cup phone openers?

@zeroampselectronics Would you be willing to post an update. I am trying to use this process on an ardiuno micro, but it doesn't seem to be working.

Gibt es eine Möglichkeit usbasp zu nutzen in der arduino ide, und damit den attiny10 zu programmieren ?

Not good. Not good.

If someone were lazy to rewrite the command, here it is in text form: avrdude -c usbasp -p m8 -U flash:w:usbasp.atmega8.2011-05-28.hex

Is there an alternative way to get the drivers for this? I’m not sure how safe Zadig is. Even though i looked up the safety i’m still not sure. If i can just use windows update that will be fine for me.

Hi, mate, do you know how to calibrate the temperature? I read that it has a hole on the side, but not sure.

Thank you from tanzania

JA.......JA.......JA...........JA...............JA

0:25 Oh I Just Naturally Thought That Was Your Third Mini Arm 🤷‍♂️

thanks you so much sir from India, can you make some vedios on how to use power meters how to undersand...etc.

What wattage is your iron?

Hello, I followed the video and instructions on your GitHub, but it didn't work, I believe due to the changes in the AVR toolchain. Could you update the video and the vscode configuration instructions to compile for the ATtiny family?

Very interesting video. The battery case and the circuit board looks to authentic. I would never be able to tell by just looking at the case. I had a similar situation recently...I got a cheap battery for my laptop off ebay...and the thing wont take a charge after 30 days or so. I cracked the case open only to find generic repurposed cells and one of them is down to 2.6 volt. I was able to bring it back to 4.2 volt, but too late at that point. I am not even sure I want to repurpose the already recycled cells...lol

Thank you for doing such a thorough test!

You will get a much better crimp if you use the non-insulated wire die of your stripper rather than the insulated die that you use in the video. The shape of the die is completely different as you can see, and when you are crimping you are crimping on the metal (uninsulated) barrel. Regardless, yes, you are much better off with a good crimping tool. Even with the better tool use the non-insulated crimping die for bare metal crimping. cheers

Nossa cara, você não é um youtuber não, você é um PAI! 🥺 Muito Obrigado, Procurei em diversos vídeos, mas nenhum mostrava dessa forma, aqui deu bom demais! Obrigado pelo vídeo! 🙌🏼🙏🏼

bro i accidently torn the anode tab,is there any way I can connect a wire there ? any vid on youtube how to fix it> ??

hi can i read write the flash of atmega 8 with the above programmer ? thanks on advcance

Lol I didn't know replacing a laptop hard drive was so easy, I thought there were cables and motherboard connectors involved etc. I never opened up or even owned a laptop before, just bought a second hand one to learn Linux. Startup is very slow on the hard drive, so the ssd should help a lot.

Thanks brother

Thank you from Cyprus. 2 key takaways... connecting the usbasp to the board and the firmware.

😮😅😊😅

all about solder wire , mine melt over 250 and above

So 55°Celsius cannot melt the lead on my old phone Poco f1? 😂 My poco f1 always overheat at 55°C when I start playing games and I guess it can reach up to 60° 😂😂

So many attempts at trying to figure out how the INPUT mode works and nothing... then this video just put it all into perspective. Big thanks!

ok not bad but now show me how to do it on 1.2mm step pin headers !!!???

This programmer along with avrdudess is not detecting at mega8 or tiny13 on breadboard setup. But using to program mcu on a dev board is getting detected!

well done!

This worked beautifully! Thank you!

Contraseña Bios. Me.aparece

Can i replace my dell latitude e6430 hdd to ssd too?

This has been very helpful, thank you! It helps that I have the same screwdriver set, makes me feel like I can really follow along, 😂

This video was terrible

Thanks a lot, you are the one who explained clearly

Sr where to buy a new (DDR 3 2x32(64GB) and 2 disc500MB solid ssd or 1TB and the batery can you sendme a links plese ? and if I do that. can I see videos 4K fron gopro 12black? or is too old this PC and I need to buy a new one

very helpful video. my two custom pct projects failed without any logical explanation, then I suspected the prosit flux and I saw this video. thank you. I will never use anything of this brand.