Thank you so much for this hack my table had sentimental value attached to it...I'm just amazed the fog stain came off..Thank you 1:51
@thisisme1999Күн бұрын
I picked up an oak coffee table dirt cheap because it had white marks on it. This worked so fast to remove the marks! Thank you so much for the post.
@Woodified17 сағат бұрын
That's awesome! Enjoy your new coffee table.
@robhulsonКүн бұрын
Tried this past weekend, succeeded. I can't believe that heat is the solution to a heat mark, but here we are.
@Woodified17 сағат бұрын
It's like magic
@rtrhino32542 күн бұрын
Thanks for share..
@Woodified17 сағат бұрын
UR welcome
@robhulson2 күн бұрын
I am warming up my iron to try this. We'll see if this is indeed a case of fighting fire with fire. Or at least heat with heat.
@robhulson2 күн бұрын
Hot diggity iron. It worked!
@Woodified17 сағат бұрын
Thanks for sharing your results!!
@hosseind63123 күн бұрын
thank you❤
@Woodified17 сағат бұрын
You're welcome!!
@zayacrawford1716 күн бұрын
Amazing video, thank you! What about bleeding it?
@Woodified17 сағат бұрын
I only changed the module not the pump so the lines were never disconnected.
@zayacrawford17117 сағат бұрын
@@Woodified thanks for the reply man! How do you know if the pump is bad??
@masterofwalo11 күн бұрын
I’m gonna try it and see
@g.o.fgaming69269 күн бұрын
Did it work?
@Woodified17 сағат бұрын
How did you make out?
@shahidakhalid57911 күн бұрын
Best idea, it does work 😊
@Woodified17 сағат бұрын
It works for most. Did you try it?
@anaya379516 күн бұрын
🎉🎉🎉🎉🎉 thankyou !!
@Woodified17 сағат бұрын
UR welcome!!
@Here-n-there198419 күн бұрын
Mine only does this when I play music really loud on a aftermarket stereo
@Woodified17 сағат бұрын
That's your car rocking out to your tunes, LOL.
@user-nj6ug7tm3f21 күн бұрын
My clio 1 1.4 speed needle going up and down while driving. What could be the problem?
@Woodified17 сағат бұрын
Sorry. I'm not a mechanic. Did you get your problem fixed?
@milagrosbraelfort309323 күн бұрын
I remember doing this years ago but I looked it up for confirmation and here it was. It absolutely works! Thanks for the reminder!
@Woodified17 сағат бұрын
Great!
@cryptoconnoisseur521024 күн бұрын
Just out of curiosity with 16” squared 3/4 plywood and your 14 and half inches 2x4’s. Would the inside diameter of your boxes be 13” squared?
@Woodified17 сағат бұрын
correct
@josephfrankappiah-nyamekye254229 күн бұрын
I'm just calling from Ghana. Assuming I want the module to replace the faulty one, how much will the module cost fro your end there.
@Woodified17 сағат бұрын
$75 - $120 USD
@holymoly271Ай бұрын
With my hard clay, it would take a hour to dig😮
@Woodified17 сағат бұрын
Did you get your planters setup?
@DLV42Ай бұрын
EXCELLENT VIDEO . THANK YOU.
@Woodified17 сағат бұрын
you're welcome
@ccristiiiАй бұрын
Omg, you saved my vacation life 😅😅!! I was worrying like crazy that I destroyed the table in AB&B and then I found your video and table is like new 😊😊😊thanks!!!
@Woodified17 сағат бұрын
Glad I could help!
@jadajohnson7957Ай бұрын
Should i use hair dryer to remove white heat marks off wood table
@Woodified17 сағат бұрын
I think it could work. Did you try?
@CrimsonCosАй бұрын
Could I replace the tape measure using a string for example? Or would it be better to just copy the mechanism
@Woodified17 сағат бұрын
Good question. I think it would be possible. Pull starters on lawn mowers have cord. Let me know if you get it working.
@rudypadilla9626Ай бұрын
Got mine free 🤣🤣🤣🤣. Fed ex dropped it with original order. Hold up you have another box 🤣🤣🤣🤣🤣
@Woodified17 сағат бұрын
Box in a box
@PowerMagStoriesАй бұрын
how do people come up with this stuff lol..but thanks, now i can save my brothers desk before he finds out
@Woodified17 сағат бұрын
LOL!
@floridasaltlifeАй бұрын
Great video
@Woodified17 сағат бұрын
thank you!
@tariromavingire8473Ай бұрын
This worked on my coffee table 23/06/2024
@Woodified17 сағат бұрын
Great!
@christophersiano2616Ай бұрын
Just did this trick to my in laws stairs that I steam mopped and caused white marks. Can confirm cotton setting on iron with no steam!!
@Woodified17 сағат бұрын
Thanks for sharing your results for your stairs.
@brittanybutler2211Ай бұрын
Works
@Woodified17 сағат бұрын
Nice!!!
@rickyvideo375Ай бұрын
nice make Play Button wood This way you don’t have to buy it youtube diamond medal too noble
@Woodified17 сағат бұрын
thanks for watching
@aldovalenzuela3568Ай бұрын
Friend..!!!!.como se llama la goma que usas....un saludo desde Chile en Sud América...!!! 🇨🇱
@Woodified17 сағат бұрын
No recuerdo de qué tipo es. Puedes utilizar cualquier material de lámina de goma.
@LMinSantaBarbaraАй бұрын
Has anyone tried this on a table with a waxed finish?
@greyes992ifyАй бұрын
That's how I got the white stain, trying to iron a dent and got a white stain
@Woodified17 сағат бұрын
How did you make out?
@AlleneQuincyАй бұрын
High help! Thank u!
@Woodified17 сағат бұрын
awesome!
@DodgerRocketАй бұрын
How do you match the serial numbers for the modules not every module is a sure fit for the car correct ? I was told it needs to be programmed by Toyota Dealer . Can someone help me on what to look for so I can match the right ABS actuator .
@trevorchristensen4103Ай бұрын
Found some around $70 +/-. You will need to look for a part that matches your year. Most eBay salvage yards will have the compatible years listed. the other thing is to look at your vin and see if it matches the correct letter on the 5th digit. ex: "F" would mean that it is an American built vs a Japanese built. For some reason the American and Japanese aren't compatible or so it seems. An earlier comment by @basitgill7519 said that you don't need to reprogram it but I haven't %100 verified ( so far currently under way with my repair). initially I got 7 error codes but if you clear them with a standard code reader and only 1 came back which might be because I only changed the electronic portion. if you change the pump area ( back half with the hydraulic lines - not just the electronics portion). then you will have to bleed the brakes to not get other errors such as a master cylinder pressure sensor error because of air. I'll comment again if I get it fully back up and going.
@DodgerRocketАй бұрын
@trevorchristensen4103 Thanks I needed the one with a " T" letter on it. Swapped out the electronics portion. All light codes went away and air stays on now ! The part cost me 116 . Compare that to 1600 wanted from dealer just for part. Mechanic would of charged me 750 to repair .
@trevorchristensen4103Ай бұрын
@@DodgerRocket glad to hear it worked! I finally got mine fixed. I had a damaged computer potion( punctured). So I figured just the front half was needed. It must have fried the master cylinder sensor at the same time. That’s housed in the back half( it has the 4 copper pins that stick out.) so I ended up replacing the whole unit and bleeding the brakes after. Can confirm though that this skid control ecu doesn’t need to be re-programmed with vin numbers or anything.
@Woodified17 сағат бұрын
Sorry I late seeing this comments however others have helped you out. Glad to hear you got your ABS repaired. I too did not have to reprogram the unit.
@garyv2196Ай бұрын
I was told that you have to connect it to a computer to clear the codes and to tighten it in an X pattern
@Woodified18 сағат бұрын
I didn't have to connect mine to a computer. X pattern seems like a good idea.
@user-lj5jo7ns2kАй бұрын
Grateful for this video and for you sharing it with the world😊
@Woodified18 сағат бұрын
You're welcome
@jkell422 ай бұрын
Worked for me!
@Woodified18 сағат бұрын
Nice!!
@fatimaadnan9112 ай бұрын
Omgg this really worksss 🤩🤩
@Woodified18 сағат бұрын
It's like magic
@fredhampton17862 ай бұрын
Those cuts have a very high probability to be off if you didnt check your 90 and 45 angles as well as the fence.
@Woodified18 сағат бұрын
thanks for watching
@jasminaanandpara92702 ай бұрын
You saved me too!
@Woodified18 сағат бұрын
Nice!
@wendydecaires17362 ай бұрын
My problem after the first replacement was a defective module. Once I got the second one, it worked :)
@Woodified18 сағат бұрын
Great that you got it working
@ronhau15422 ай бұрын
I thought the dust collection was excellent.
@Woodified18 сағат бұрын
I stopped using the dust collection on the blade guard.
@ronhau15422 ай бұрын
Wow I learned a lot! Great review!
@Woodified18 сағат бұрын
Glad it was helpful!
@countryside81222 ай бұрын
I got my stand all together no problems HOWEVER after I mounted the saw to the stand I discovered that I had NO RIP FENCE with the saw!
@Woodified18 сағат бұрын
That sucks. Did you get a rip fence sent to you from dewalt?
@callofgeorge2 ай бұрын
should be sponsored by dewalt. just sold them a saw. well almost. honey sent me an email for a price drop on it to $550, started watching this video to make sure i was making a good purchase, but by the time the video was finished the price went back to $650...
@Woodified18 сағат бұрын
Thanks. Dewalt never replied to my messages :( Did you end up buying the saw?
@callofgeorge16 сағат бұрын
@@Woodified sure did. it eventually went back on sale. i have a small wood working shop essentially now.. or the tools to become one lol. ordered the locking dado stack for this saw, bauer planer, wen jointer, flip top bench for those 2, already had a compound sliding miter saw, clamps galore and several hand power tools.
@Dontneedahandle02 ай бұрын
Thank you, I’m going to try this. I had a friends mom tell me once, that if you use mayonnaise and it dry to clear, the. Wipe it off and polish, it will do the same thing. The smell of mayonnaise would be strong
@Woodified18 сағат бұрын
Did it work for you?
@Dontneedahandle017 сағат бұрын
@@Woodified it did! I did it to my great grandmother’s buffet. The ring came out. I like it better than the mayo method. I just can’t get past the smell. Thank you again!
@215ftr2 ай бұрын
Im about to remove my module on a 2013 honda accord once i remove the abs system what do i do with the break lines because im sending out my abs for repair?
@Woodified18 сағат бұрын
sorry just seeing this now. I'm sure you figured it out
@MariaRodriguez-kc8ui3 ай бұрын
Does it have to be done immediately?
@user-uh4yj9cy6kАй бұрын
good question!
@ccristiiiАй бұрын
No
@Woodified18 сағат бұрын
Did you get the mark off your table? Others had stains that were 2+ years old.
@nilsaehterami93413 ай бұрын
THANK YOU!! Mum wont end me now. I used a small face towel, low setting (like 1/3), no steam. Took maybe 20 seconds. Lifted the towel every now and then coz I didnt want it to stick to the table.
@Woodified18 сағат бұрын
Great! thanks for sharing your results.
@nancyvanderburg46343 ай бұрын
I thought I was going to have to get rid of my table but this worked perfectly. Thank you!
@Woodified18 сағат бұрын
You're welcome!
@TheDaneYard3 ай бұрын
Thank you!!!! You saved me
@Woodified18 сағат бұрын
You are welcome!
@horses2by3 ай бұрын
Wow that’s an amazing SteamPunk Lamp
@Woodified18 сағат бұрын
thanks
@esu___esu3 ай бұрын
Literally saved me and my mom many tears with this😫❤️. This actually worked and so quicklyy the table looks great again🫶. Thanks a lot!!!! That’s why I love KZbin.