Hermosa y muy bien pensada caja. Gracias por compartir y muchísimas gracias por obsequiarnos el pdf. ☆☆☆☆☆
@aparecidonovaes9826 күн бұрын
Perfeito
@LarrySmith-l4q6 күн бұрын
This is supposed to be one of the first tools you need when you set up a shop, but you need a router table and a drill press to make it. Chicken and egg?
@mmujicic7 күн бұрын
.
@maritesabina2448 күн бұрын
Me ha encantado aunque un poco complicado para mí pues no te fo todas las herramientas, me sorprendió la regla, podrias decirme como has hecho la regla? Gracias
@beceriksiztalebe74628 күн бұрын
Piknik tüp çıkışına alev geri tepmesini önlemek için aparat mı taktınız?Taktığınız aparatın adı nedir,selamlar.
@ray081318 күн бұрын
Thanks so much for your diy posts! I was not able to download the pdf for the angle gauge. Could you please send it to me?
@pierreblondel8589 күн бұрын
Très beau mais trop long à réaliser
@richardc62699 күн бұрын
Ideas 💡 are wonderful!! Cool🤑😉
@Tom-gv2eo10 күн бұрын
Great ,clever design! But I woud have made the base wider, broader , thicker (your small area base means it's top- heavy with a power drill at the top) You hav used some costly professional tools to make it (-never seen a power chamfer edger b4) -beyond th resources of some D I Y -ers!
@richardmichels220812 күн бұрын
top
@zdenekdanda822112 күн бұрын
Good Idea! Thanks.
@sot11cat12 күн бұрын
Hello from Greece! Nice job!
@alcaponehome674413 күн бұрын
How to determine the correct angle please ?
@hope4ourfallen9 күн бұрын
You can lay blade down flat on stone (like how it would rest if you just set it on a counter) Then slowly tilt non cutting edge upward until you see no gap between stone and cutting surface. (This can be hard to see sometimes for some of us though) But if you take a permanent marker and put some marker along the blade (on the sides of the cutting edge, where you intend to grind off) it will get erased by the stone and make it easier to see if you need to adjust the angle. Ink remaining close to the cutting edge, but scratched off closer to spine (raise the angle) Ink remaining on spine side of section you are trying to sharper but cutting edge is scratched away, (lower angle) Ink removed in a nice even appearance only on the sharpening surface(like we see when you look at a parkerized pocket knife) then you have a good angle. Hope that helped and didn't make it more confusing 🙂
@alcaponehome67449 күн бұрын
@@hope4ourfallen thanks a lot for the explanation 🙏
@IantheWoodcraftsman14 күн бұрын
Well done -- works well!!
@IantheWoodcraftsman14 күн бұрын
Good job! I liked the adjustable infeed table that most similar jointers don't have.
@jesuspantoja337314 күн бұрын
Doblemente ilustrativo, muchas gracias por compartir 🎉🎉🎉😊😊😊
@crumblenaut977616 күн бұрын
The Genius is back with another great project! It's really nice to be able to use both a planer blade and a chisel. Thanks for sharing!
@JaymeUbiriciLehugeur17 күн бұрын
Wonderful work!!!
@canoelew228818 күн бұрын
Either start a narrative or I’m outta here!
@che-luison498419 күн бұрын
Awesome
@albertcebriariu446919 күн бұрын
😊
@AliAkbarSheidaei20 күн бұрын
💯❤❤🙏🙏🙏
@armindo.santos20 күн бұрын
Excelente, ótima opção
@markduggan345121 күн бұрын
Excellent, that really is excellent.
@frenchgreguk21 күн бұрын
Awesome.
@craigwatkins565421 күн бұрын
That center punch is brilliant!
@albertcebriariu446921 күн бұрын
😊
@ilknurozkan452421 күн бұрын
Ellerine sağlık ustam yine güzel bir iş çıkarmışsın tebrikler
@alpertolgagedik895421 күн бұрын
great job
@михаилроманов-ф7ч21 күн бұрын
Отличная работа! Спасибо за видео! ❤
@MCsCreations22 күн бұрын
Fantastic work, dude! Really well done!!! 😃 I already downloaded the plans! I'm definitely going to build one as soon as I can! Stay safe there with your family! 🖖😊
@bennylee641822 күн бұрын
“If you can made,who need to buy.” Use it for the slogan,please.
@RealTakunia22 күн бұрын
Çok iyi! 👏 Ancak bıçak çıkışı biraz geniş gibi. Belirli bir sebebi var mı? Zira o geniş ağızdan içeri epey bir malzeme girer ve kesmek zor olur gibi. Saygılar.
@brianmarshall721422 күн бұрын
Bloody magic mate!
@Hanimichal22 күн бұрын
the mouth opening is too big should be between 1mm and 0.6mm
@JohnColgan.21 күн бұрын
I've got at least 6mm mouth on my old Stanley No4 & No6,
@ralphhenderson608622 күн бұрын
Awesome
@Gizemli1Adam35722 күн бұрын
Elinize emeginize saglik,guzel bir calisma😊
@SehmusKaya-sl1ho22 күн бұрын
❤
@rudolfbo597523 күн бұрын
Perfect video, I like they idee.
@casiovila80223 күн бұрын
Muy bueno felicitaciones
@АлексейКарепанов-х1о25 күн бұрын
Супер. Хороший инструмент, вы молодец . Очень классно. И ещё своими руками. Так держать.я завас😊.
@robsonserafin821927 күн бұрын
Fantastic classroom, I would call it as a show because that is full hard work to present such nice video. In youtube the idea behind is to incentivate people to learn how things works, how they can be made and above all, how they can be innovated. Nobody would be able to improve or add inputs if the hard initial part, the base of the project wasn't created, from scratch. Congratulatios.
@oldbonesbushcraftrodjackso47427 күн бұрын
Very useful and practical simplicity Very nice. great concept . Yes i like this method very much . Thank you .