FYI, this washer has thread lock on the bolt in the drum. I found out the hard way and broke the bolt. Now I have to figure out how to get it out.

Question is, why is it leaking?

How much does it cost to have technicians to replace terminal block?

Thank you for the video! Had to replace the rear roller. I knew nothing about this repair before watching your video. Roller cost me $60 dollars. Just saved close to a grand by doing it myself. Easy to disassemble on your own though it's a two person job putting it all back together especially holding the drum in there.

PERFECT Video !!! Took me about 4 minutes. Thank you !!!!

Does the wiring place matter (on spade terminal) White and Rogers Emerson HSI single stage gas valve? (when disconnecting and connection gas valve wires) I ask because some said " Make sure the black one is in the back" Appreciate you and your answer

Thanks so much for this video. Got charged an 80 trip fee to be quoted 390 to replace the knob and timer. Your video helped me do it myself in less than 30 minutes and it only cost me 96 bucks 🙌🏽

I want to thank you I'm eating Pizza tonight because of this video!

i was able to fix mine. Thanks for the good video.

This video saved the cost of a service call which would have been a least a couple of hundred dollars not including the part....my wife was happy that she didn't even hear a curse word. The over under was 20...😅

Thank you for this video. This is probably the clearest home improvement video I've ever watched. And, of course, I was able to successfully complete the job!

Why do i yave to remove the entire front panel?

i have this same one nothing but trouble just junk three carbs and they still leak and its not the fuel line!

How do I know if my part needs to be replaced? I mean, how does this part get damaged? What are the signs that indicate the part needs to be replaced?

God. That's a lot of work for a small part.

THAAAAAAANNNNNNKKKKKSSSSSS!!!!!!!! I've just repaired my washer with your help.

My fridge doesn't seem to have clips to take the old LED light off. Are some not removable

Cheers for the video mate.

Would this part cause d80 error code to pop up? Cleaned vent duct,dryer internal. Ensured no blockage. Can feel air passing through at end of duct run. D80 keeps showing

This was super helpful and my wife was fixing to make me buy a new fridge, thank you!!

My icemaker keep having a constant banging noise for about a half a minute and then I don’t know maybe half hour later it does it again and it keeps repeating it ideas

THIS WORKED 💜💜💜💜💜 Thank you!!

You're the best. Worked. LG wanted to charge 400 to come out. Thank you so much

Thank you so Much for this video I got everything off on the outside of the wheel, but I didn’t realize there was another clamp ring on the inside part that need to come off thanks again👍

Heated blankets work in similar principles. Inside of heated blankets, there are electric coils inside of the heated blanket. When the power button is pressed, voltage is sent to a thermostat, then to a heating element to heat the blanket. After that, the voltage gets cut off to the thermostat to prevent overheating. Some models have sensors, or a timer to prevent overheating. If it overheats by 10 degrees, the thermostat, sensors, or timer has failed, and will need to be replaced. btw i added this in because you forgot to make a video about the heated blanket i think

Thank you! This really helped, had already looked at the condenser fan but it was the freezer fan that was making all the noise.

By

How does the top release? It clearly has some kind of latching mechanism.

Tech came out and replaced the fabric softener dispenser because it was leaking, then a couple of days later it was still leaking, tech came back and couldnt figure out the leak so he blamed the water pressure. I called another company and this tech said there is nothing he can do because he has seen this leak many times and called it "mistery leak", and while showing me how water fills the fabric softener reservoir he broke the top part lol still mad about this issue, washer is in his 4th year and didnt have this problem until a couple of months ago...

Thanks much!!!

Thank you.

Is there a thermal fuse in this dryer? I'm thinking not because I'm not able to locate it.

Does anyone have info on the part in the lid that connects to the housing unit? My tab is broken, so do I need to replace the whole lid?

So it looks like there are two solenoids, but only one is being replaced here. Should I buy and replace both or how should I test them to know which one is bad?

😂😂😂😂 very usefull advises

Great video

Are there holes on both sides of that sprayer. My GE only has holes on one side and not sure if they should be facing down or up?

what was need to remove the upper rack? i works without removing this part.

I can’t get the rear rack stops off and this is my fix. I haven’t even used this yet.

Took front & top panel off. Latch was in (Closed position) Spray, WD-40 Opened the latch Shut and opened the door several times. Put everything back together And now it works. Thanks for the great tutorial video👍❤❤

Can you give me the part number and where to buy it please?

What size is the bolt

Where does the ground wire go

I removed the drain hose from the bottom entry (its exposed by a big opening) by tilting the washer back, I was able to unclip the hose from the bottom using my hand. I feel tearing your washing machine apart is completely unnecessary.

Very helpful. Thanks.

GE stackable washer GTUP240EM5WW water inlet valve replace - any how to videos or other?

My handle is loose on one side so this is exactly what I need. Looks like a simple mounting stud needs tightened. Didn’t know those little set screws were hidden on the bottom. 😊

I sheared off the crank shaft to my chipper. So I’ll be giving this a shot. 😅

The disassembly and reassembly is fairly logical, but this video gave me the reassurance I needed before attacking the job. The production is very clear, from both an audio and visual perspective.

One recommendation. Make sure the refrigerator is on. Test amp draw - normal draw when compressor running is between 100-300 watts. My 2 door GE runs at 225W. Manually cycle defrost cycle. Use screwdriver to rotate manually the timer on the defrost timer. It is usually behind a panel in refrig area at the top near the temperature dials. Rotate the manual timer until you hear it click hard. That is the defrost circuit being powered on. The compressor will turn off too. The amp draw will jump up to 600-700 watts for roughly 10-15 minutes. If you see that your element is working. Also the temp in the freezer will increase to the 30 deg range after the 12-15 minutes of the element being on. This allows you to validate element working without taking it out. Good luck!