A quel degré le guide d angle a été régler? Et si on est pas sûre du degré le truc du crayon feutre est applicable ?
@OutilsVielToolsIncАй бұрын
Sur un couteau de chasse, normalement c’est entre 10 et 12 degrés. Effectivement, le truc de crayon feutre peut aussi fonctionner 😉.
@guillaumemasse8608Ай бұрын
Merci de votre réponse! Je viens de m'équiper chez vous et j'ai bien hâte d essayer votre produit
@toddbenko67013 ай бұрын
Note The veil clamp in many cases does not report the actual angle of the edge because if you look at time code 0:40 that the bottom face of the clamp is used to hold the outside edge. Almost all quality scissors have a sloped outside face. This means the 0 angle is relative to the outside slope when clamped as shown at time code 0:58 and not the inside cutting plane of the scissor. Therefore for many scissors the angle on the clamp means absolutely NOTHING regarding the cutting angle. The video is only showing how to use angle reference for a scissor where the outside edge is parallel to the inside edge.
@thewoodwork_ca9 ай бұрын
Most knife belt sharpening videos say the belt rotated away from the bevel not into it so the blade doesn’t gouge or cut the belt. I think the Viel travels down into the bevel, why is that?
C'est bien mais le profil de la dent est bien triste.(le plus commun....) . il y a tellement mieux sans être plus compliqué
@OutilsVielToolsInc11 ай бұрын
C’est pourquoi nous avons plus de 10 profiles différents pour adapter à chaque type de lame😉
@ibrahimjan624011 ай бұрын
❤good setter price sir
@robertmunguia25011 ай бұрын
How do you use the angles on the woodcarving jig?
@robertmunguia25011 ай бұрын
How do you use angle gauges on that jig?
@robertmunguia250 Жыл бұрын
What angle is it basically set at?
@zondaichinyai6430 Жыл бұрын
Can I get a pdf manual for the machine
@OutilsVielToolsInc Жыл бұрын
Yes! You can call 1-800-463-1380 and we will send it to your email.
@ferroferdinand4115 Жыл бұрын
J'ai une question, est que on peut utiliser cette machine affûtelage avec le Meil de 10/30 "5 pour le lame de Wood-Mizer?
@OutilsVielToolsInc Жыл бұрын
Non… L’angle n’est pas le même. Quand Wood-Mizer ont décidé de prendre notre concept de meule, ils l’ont adapté à leur affûteuse.
@florentsirois3164 Жыл бұрын
En français svp.
@tijosmonfarlo Жыл бұрын
Est-ce que les limeuse viel sont complètement automatisés ?
@OutilsVielToolsInc Жыл бұрын
Malheureusement non.
@marcogilbert4230 Жыл бұрын
Merci, super ces petit video
@capitainejosephblackjobart2577 Жыл бұрын
Bonjour j'aurai besoin de vs parler en privé si possible pour un project
@OutilsVielToolsInc Жыл бұрын
Bonjour! Avec plaisir. Appelez au 418-860-4442
@danymorin7367 Жыл бұрын
Salut
@francvig1570 Жыл бұрын
Merci pour les informations.
@78Malik2 жыл бұрын
Kaise mile ga sir
@chatontoutsage91582 жыл бұрын
J'ai rien compris !!!😑
@josephch67372 жыл бұрын
I want this machine
@7727777777777772 жыл бұрын
what type of grinder stone is used where to buy them?
@OutilsVielToolsInc2 жыл бұрын
Here is a link: www.vieltools.com/produit/meule-pour-affuteuse-de-profil-654
@7727777777777772 жыл бұрын
@@OutilsVielToolsInc is 8631 your part number or Tyrolit like to get a fine ginding wheel 160 grit, the image on web site is blur cant read the number on the grinding wheel
@OutilsVielToolsInc2 жыл бұрын
@@772777777777777 we get these wheel made to go with our machine. Tyrolit don’t make these for us anymore. The 8631. Number is our stock number. Wheels are 7’’ x 3/16 grit 56.
@scor4402 жыл бұрын
The French make great tools is this in the USA?
@tamcaj2 жыл бұрын
J'ai une Viel S5-M que j'aime. Pourquoi changer la plaque d'origine pour une plaque avec des roulements à billes ? Je ne suis pas encore un tourneur, mais ça devrait arriver très bientôt. Les guides aimantés ne semblent pas correspondre à ce que les tourneurs utilisent. Ce que je vois sur le Net, c'est plus 45 degrés et mes guides sont de 15, 20 et 25 degrés. Avec votre démonstration, les guides de degrés semblent bien inutiles.
@OutilsVielToolsInc2 жыл бұрын
Bonjour, Commentaire très pertinant! En fait, la plaque est nécessaire seulement si vous devez affûter des petits outils de sculpteur (aproche la courroie de l'accessoire). Les guides d'angles servent aussi pour les petits outils de sculpteur (des fois trop petit pour déterminer l'angle).
@tamcaj2 жыл бұрын
Merci, ça me rassure.@@OutilsVielToolsInc
@flavienbouttecon30323 жыл бұрын
Est-il possible de l'acheter en france ? merci
@satyachinthala71193 жыл бұрын
Iam from India, I want to buy your machine
@CL-pe4ll3 жыл бұрын
Link to any English videos? Love the mill!!
@OutilsVielToolsInc3 жыл бұрын
Not yet but will work on it! Thanks
@DmDFC3 жыл бұрын
Bonjour, les produits Viel sont il disponible en France si oui, qui est le revendeur ? Cordialement
@OutilsVielToolsInc3 жыл бұрын
Bonjour, malheureusement non…
@bucko19483 жыл бұрын
Please consider redoing this video so dropdowns do not cover the video. Also, move the camera higher so there is a more top-down view. Would help a lot
@zaheerahmad13733 жыл бұрын
Camera is very very near Please better camera fix outside the workshop 😉☺️
@yvancrochetiere54043 жыл бұрын
Est-ce que le sens de rotation est important?
@vjarreau3 жыл бұрын
Where is a link to buy the S-5-M with motor?
@OutilsVielToolsInc3 жыл бұрын
www.vieltools.com/recherche/s-5-m
@mdkhokondaibar82843 жыл бұрын
Thanks
@jeanlefebvre64583 жыл бұрын
Combien cout cette avoyeuse et où jpeux l’achète merci
bonjour Louis! I am struggling with my DU-2 duplicator setup. In particular, where the cable is connected. I believe I am missing the part that holds the cable at the headstock end. I was just sent a replacement part, but I do not believe it is the proper part. Are you able to assist me with this? The instruction manual is difficult to interpret and does not include this step.
@michelbergeron5743 жыл бұрын
Moi j’aimerais voir une vidéo de l’embarquement du billot. Accroche t- no facilement la roue dû traîler? Si je fait une rampe d’embarquement, le billot passe t’il facilement ?
@7727777777777773 жыл бұрын
What type of griding wheel used
@OutilsVielToolsInc3 жыл бұрын
7” x 3/16’’ Grit 46
@7727777777777773 жыл бұрын
@@OutilsVielToolsInc where can i buy this grinding wheel from..what mater are these wheels made from
I saw Leonard Lee (Lee Valley) using this machine in a live sharpening tutorial in the early 1990s and was impressed. Hence, I've had one for almost 30 years. It has done everything from lawnmower blades to fine kitchen knives. I used a two-speed 1/4 HP furnace motor. I really can't imagine sharpening anything (especially kitchen knives) any other way. With knives, there is nothing like a quick 10 second tuneup with a 16 micron belt at a perfect 12 degree (or whatever) angle. I use it almost daily. This is one of those tools that you think everyone should know about. Forget the mess of water baths, multiple whetstones, blah, blah, blah....
@duncanbritton19613 жыл бұрын
What direction does the belt spin?
@OutilsVielToolsInc3 жыл бұрын
Downward.
@rebellodownhill4 жыл бұрын
How can i buy this?
@OutilsVielToolsInc4 жыл бұрын
Call us our visit our website at www.vieltools.com
@jimduffy60324 жыл бұрын
Can you tell me what the S-10 scissors accessory is attached to when doing the sharpening on the S5? In the video it looks like there is some sort of swivel base it's supposed to be attached to.
@OutilsVielToolsInc4 жыл бұрын
In fact, the swivel arm is part of the S-10. The arm is attached to the S-5 exactly the same way as all the other accessories.
@ddowell4734 жыл бұрын
I've owned this sander for 4 years now, and often go to it for sanding/grinding wood, metal, plastic - you name it. I reverse engineered and fabricated the chisel jig so that now I have several different angles I can set, but their jig prices are very reasonable. I also built a small platform (box) for it to set on, with a slot under the lower pulley. I hook a shop-vac to the other end, and it does an excellent job of dust extraction, as the vast majority of dust goes down. The hand wheel accessory is a "must have" in my opinion if you are going to use it for several purposes. Highly recommend this little grinder. It is near bulletproof, and belt changes are a snap.
@robertmunguia250 Жыл бұрын
I have one as well but I need to know what the hand wheel is for? I will order it.
@JeffLambert6704 жыл бұрын
Est-ce que vous pouvez donner des trucs pour les lames courbe comme un couteau à désosser comme ça www.zwilling.com/ca/zwilling-professional-s-5.5-inch-boning-knife-31024-141/31024-141-0.html?cgid=our-brands_zwilling_cutlery_professional-s#start=1 avec la S-5, j’ai l’accessoire S9, merci!
@OutilsVielToolsInc4 жыл бұрын
Bonjour, en fait il n’y a pas vraiment de truc spécial sauf de suivre la courbure. Donc vous partez avec le manche vers le haut et au fur et à mesure que vous déplacez votre lames sur la courroie, vous baissez le manche pour atteindre 90 deg. Et au bout vous baissez le manche. Tout ça pour essayer le mieux possible de conserver le tranchant à 90deg avec la courroie.
@JeffLambert6704 жыл бұрын
Louis-René Perreault je l’ai finalement fait en mettant la S-5 à plat, puis me suis servi de la parti sans la patine. C’est pas avec le guide mais bon, ça l’a fait la job. Le guide S-9 n’est pas super stable non plus, il se déssert avec la vibration de la ponceuse. Merci de votre réponse!
@OutilsVielToolsInc4 жыл бұрын
@@JeffLambert670 En fait, le S-9 est considéré comme une pièces d'usure et doit toucher la courroie, donc même si l'écrou à oreille dévisse ce n'est pas grave. Si vous essayé de le tenir à distance de la courroie, vous aurez un jeu sur l'angle du tranchant et ce n'est pas le résultat escompté! Pour ma part, je met le plateau du S-9 à 90 deg., je sers l'écrou à oreille le plus possible, je pousse l’accessoire jusqu'au fond et ensuite j'appui le plateau sur la courroie. j'affûte 99% des couteaux avec cet angle, ce qui donne environ 10-12 deg. L'avantage, quand je ré-affûte, j'ai toujours le bon angle!
@JeffLambert6704 жыл бұрын
Louis-René Perreault ah, je ne savais pas que la pièce S-9 était une pièce d’usure. J’ai donc essayé votre methode d’acoté la pièce sur la couroie. Je trouve ça plus difficile de savoir quand il y a contact avec le couteau car quand la pièce ne touchais pas, je pouvais entendre très clairement le couteau touché la couroie, là j’entends toujours la S-9 touché alors pas d’indication sonor. Peutêtre une question d’habitude. Aussi, la S-9 que j’ai ne va pas jusqu’à 10° même appuyé jusqu’au fond, alors j’ai dû faire un encave dans la bar de soutien des accessoirs pour qu’elle puisse se rendre jusqu’à 10°. Pour ce qui est de prendre toujours un angle de 10-12°, la plupart des couteaux que je rencontre sont a un angle beaucoup plus grand que ça, alors je dois toujours vérifier avant pour éviter d’enlevé trop de lame à chaque fois et respecter l’angle d’origine le plus possible.
@normandfontaine55084 жыл бұрын
Bonjour, vous affutez le fer au papier grain 120 seulement ? Doit-on aller jusqu’au grain 320 en passant par le 220 ? Merci.
@OutilsVielToolsInc4 жыл бұрын
Bonjour! avec un grain 120 c'est amplement suffisant. La majorité des affûteurs professionnelle utilisent un grain 80 ou 60.
@catalin-neculaigherasim1884 жыл бұрын
I am from Romania, do you know were i can buy this machine and be shipped to Romania?