You spelt braai wrong

Very useful video, thank you. I’m not using a controller like yours, I’m converting a laser cutter. I’ve got the relay working with the laser, as in turning on and off when it should. Do I just need to bridge the 2 wires coming from the plasma trigger, and connect them to the normally off circuit on the relay?

I've got a MKS DLC V2.1 card and I have hooked it up to my homemade desktop CNC machine which I plan to use to run a plasma torch. I'm completely new to all of the CNC building and breakout board business so forgive me if my question comes off as somewhat of a obvious or a newbie type request. I'm running open builds control to send the information to the board and from the bored I'm going to tb6600 drivers. Those drivers are sending their signal and power to 3 nema 17 motors controlling x y and z. Everything is functioning great except when I try to run the program I get a error stating the z axis probe is not in the expected state. I've been told this is because I have set my parameters to require a touch off operation but I have no sensors on the table yet. No probe switches and no end stops. This all makes sense to me but I'm wondering if all I need to do is hook up a z stop or z probe to get past the error code that stops the machine when I'm trying to do a dry run. Any advice is greatly appreciated. When I attempt to run tha G-Code the Gantry moves to the first cup position and the z axis goes upward, then it returns the error code. I'm guessing this is because the z axis does not know where it's at. So do I hook up a switch to the probe connector on the board or the z axis and stop? When I created the G-Code in open builds design I did tell the z-axis to go to a safe height of 10 mm. But I didn't tell her anything more than that. I just figured if I zeroed all the axis before starting it would just automatically go up 10 mm and then drop down to my cut height and begin following the toolpath pattern. I'm going to check out some more of your videos and subscribe. Thanks.

Is cool this machine! what is torch model is use to high definiton?

How can I contact you. I stay in Middelburg Mpumalanga and I am stranded with my project on my cnc. Help please!

will it work with a hakko fm2024-02 desolder gun?

Can i powar cnc shield 12v 10amp

Are USB parallel adapters dependable? I’d like to try an old scanner.

Thanks for the vedio I really like it can you please get me the wiring diagram of how to connect arelay on plasma source with mach 3

Can we please have a part number for the single 5v relay switch? Amazon prefered.

Sir , plz tell me How to configure the floating head micro switch in the mach 3 to sense the initial height ??? The settings in the mach 3 ???Plz reply. .. plz

Sir , plz tell me How to configure the floating head micro switch in the mach 3 to sense the initial height ??? Plz reply. ..

Any chance you know the connector number for the white connector that plugs into the M-Fin P8 location on the board? $95 for a plastic plug and two wires seems a big excessive.

Thanks for sharing your experience with us!

Great video! Easier to follow than the HAAS manual.

My plasma torch fires when is not supposed to and it stops when it supposed to fires Can i reverse that in mach3?

Wish they had stock still, on a waiting list still.

I have one question sir, I have a Chinese CNC machine which make some weird noise at some point, i am thinking it is a wired connections are not good any suggestion, by the way my question is if CNC motors are different in z and same in x and y we need to change the dip setting for z axis separately or can we use the same dip setting on the x and y by default it is same for all axis

hello what display model is needed to install on unisolder 5.2 thanks ..

Total cost ?

Great video, thank you! I bought this from the same seller and it works great. But I couldn’t figure out how to wire the sleep sensor to the board and the seller couldn’t tell me how either. Can you post a diagram or something? Thanks!

Dude, THANK YOU! Honestly, this is the best "Stepper Motor CNC Setup for Beginners" on KZbin. I've tried watching other ones, but dang... they're sooooo boring!!!! This was easy to watch. Much love, Bro!!!!

Can we give saprate power supply to relay OR give 5v power from mach3 usb board ?

Well done

Greetings from a fellow South African :). Thank you for a really useful video! Looking forward to the Unisolder vs JBC DDE showdown.

please, give me the design file of machine, equipment, tools to make it to email: [email protected] . Thanks

Nice one, I have just realised how old my machine is now looking at your board. Never mind the controller. Im inspired to look at mine now for external functions.

Thank you so much for this! Also, you sound like Thor lol.

Nice to hear that SouthAfrican accent again. What size stepper are you demonstrating with? Nema 34? How many ounces of torque?🇿🇦🇦🇺🇬🇪🇷🇺🇷🇺🇷🇺🇷🇺

Sounds to me like you had conflicting addresses or interrupts.

Great video, comes in really handy. I have the same board, though they seem to have forgotten C13. Did you have to flash the firmware or did it come preinstalled on your board?

Dear sir can y send me wiring digram from cnc controller to spindels to [email protected]

Very well explained. Have you ever had any problems with emi?

Hey, does that little senseboard come with the tindie package? or is that something you made yourself. It looks like it splits into 3 and then goes to the board. How is it wired up exactly?

The Tindie site doesn't list the Pace TD200 iron. I thought it was supposed to work with the Unisolder?

Hello sir, i also made the cnc plasma machine without THC or z-axis. When i doing any job on the cnc is plasma torch is always on. When i doing holes in metal sheet is holes are done but the path is also cut. Pl's help me. The THC is needed to torch on/off or failure of sheetcam design when i made the design.

Hey, I just assembled everything according to your instructions. Thanks for that! However, I bought the original JBC iron and the connector is obviously different from the knock off version you're using in the clip. I couldn't find anywhere the pinout of the original T245 iron. The description in the "valerionew" github repo only refers to colored wires, so I'm not sure how to interpret it. Do you know where it can be found?

hey im using smps.also got toroidial transformer.is it better u think using that? currently using 12v 30A smps

Las dimensiones de corte y para los tornillos para la parte frontal y trasera?

Can I ask what is the little box with up down arrows an how did you wire it up as am trying to do the same with my hf50

Did you bought the handle from the same store on tindie? It comes with a small plastic part 2.5 cm in length and I am not sure where this plastic part is suppose to go. Do you know?

How limiting is the 6A limit? Are the sub ~144W JBC irons enough? Because unfortunetly you can't use the 250W bad boys on this.

Did you also order a soldering iron from Tindie? It's replica so I'm curious how is the quality? Is it usable?

HI. NEED TO TALK TO YOU PLS. CAN YOU SEND ME A MAIL. [email protected]

quick question, what keeps the tip from hitting the metal as it travels or is the gap big enough to accomodate a workpiece that isn't perfectly flat and doesn't warp. I like simple, I have a magnetically mounted torch hold with the spring loaded touch off. I am using an electronic connection for touch off, grounding the piece and the tip is the other connection. Anyone?

Great presentation, can you link your soldering iron holder?

❤️

Thank you sir

Can you show me how to hook up the torch and relay to a gecko 540?

How many amp power supply do you need compared to the amp rating on motors ? I read you only need about 2/3