Would a bad PVC cause the car not to start? Son was driving home and it just died. I'm getting a 2177 error and it cranks over, but will not start.
@ethanrushbrook33143 ай бұрын
Highly unlikey. A bad PCV valve is more likely to cause rough running or smoke blowing
@johnniewalker37179 ай бұрын
What year is the Mazda 3?
@cm93596 ай бұрын
Great question.
@lannyhancock913310 ай бұрын
Promo-SM 👉
@7mooks10 ай бұрын
On the rear passenger side, the adjustment hole is in 9 o'clock position. To tighten up all the way, adjust it to the right. Then to loosen up, just 4 click to the left should work.
@henrynguyen57587 ай бұрын
Hello, what about on rear driver side , 3 or 9 o’clock . May I have more details, thank you
@7mooks11 ай бұрын
This is only a Toyota and not a Ferrari.
@MetalAsunder11 ай бұрын
we don't make enough! drives off in 60k sports car........
@thearmedgardener11 ай бұрын
Imagine driving a supra and saying u don't get payed enough. Just fucking leave Cali
@bandmankai11 ай бұрын
you forgetting maybe it’s her husbands car and she works there? rich people only wanna get richer so
@7mooks11 ай бұрын
It's only a Toyota not a Ferrari.
@Imthatguy18711 ай бұрын
Innit bro 😂
@grinbeefive416911 ай бұрын
sick mkv
@bastogne31511 ай бұрын
Is pcv valve in same location for 2016 Mazda 3 petrol. Thanks.
@chloeleedow7250 Жыл бұрын
Most stupid design for a pcv valve every, hours or labour for a 20 dollar part. Having to take the intake and crap off, who not put it on the top of the damn engine like the 1ZZ-FE corolla engine for example! 2 minute job verse 2 - 3 hours easily even in a proper garage. Assholes 😂
@mrprosale Жыл бұрын
Tjhanks for posting this! I don't like breaking these small fittings, hard to find new one, cheers.
@ricebike Жыл бұрын
1:47 uhhh the o-ring seal for the pcv is still in the plastic oil air separator! make sure you re -use it or buy a replacement o-ring. i also be prepared to get a new plastic ring since it may be brittle now & prone to break apart when prying too hard.
@davie29832 жыл бұрын
Do u have to take any other parts off the car to see it? I have a 2010 3i.
@uptospeedofficial Жыл бұрын
I think you have to remove the intake manifold
@uptospeedofficial Жыл бұрын
kzbin.info/www/bejne/g5_cZWCpp7KXhbc I think this is what you need to do. Im not exactly sure though.
@chloeleedow7250 Жыл бұрын
Yep horrendous job for a 20 dollar part, whoever designed this part of the engine needs a smack 😂
@dillyhahaАй бұрын
@@chloeleedow7250there are cheaper parts inside your engine block, cope
@aaronthomas74462 жыл бұрын
Trying find the ring mine is crack
@jerrymanuel26072 жыл бұрын
Taga tabuyoc po kame
@mzr35532 жыл бұрын
If u do break it.there is a ford alternative part nr.ford mondeo 1.8 duratec use same ring
@chloeleedow7250 Жыл бұрын
Shared Ford parts for these including the whole engine are cheaper too! 😂 I'd always go Ford for spares on most Mazda l engines
@JuvsInTokyoLearnNShare3 жыл бұрын
Nagmayat met ditan bosing!
@moiseskojibitao31198 жыл бұрын
ang Sarap balik Balikan ng Mga nakaraan ! woooHh ILoVE TABUYOC <3
@7mooks14 жыл бұрын
Dito sa Tabuyoc yata ay hindi nauubusan ng beer..... hehehe