Hello sir do you have a contact number? I brought a used pcm online for my 2017 ford fusion se. I need it programmed to my vin and keys. Thank you!
@serobmanucharyan355413 күн бұрын
Bro, between can-H end can-L connected a 120 ohm resistor?
@markdasparkauto178012 күн бұрын
Yes you can put the resistor between high and low but it's much easier with the adapter.
@serobmanucharyan355412 күн бұрын
@@markdasparkauto1780 So your adapter already has a 120 ohm resistor?
@serobmanucharyan355412 күн бұрын
@@markdasparkauto1780 Did you download the firmware and coding from the old TCU?
@markdasparkauto178012 күн бұрын
@@serobmanucharyan3554 yes I did I had the file saved before. so all I do is renew and write the file into it
@serobmanucharyan355412 күн бұрын
@@markdasparkauto1780 friend, another question for you, if the non-working board is 722.9 V2, and I install the donor 722.9 V3. Will V3 work with the old firmware V2?
@GhaithAlshaary2 ай бұрын
Is this just for the old model s Can I use it in the 2021 models I can’t find My car and can’t know how to wire the conenxters U know new Mercedes has a ignition switch module under the seat How can I read that ?
@markdasparkauto17802 ай бұрын
I believe after 2016 that was it 2016 envelope you are good
@GhaithAlshaary2 ай бұрын
@@markdasparkauto1780 what do you mean by envelope ? Can’t find my model so can’t read it
@markdasparkauto1780Ай бұрын
@@GhaithAlshaary after 2016 no way only dealer
@cregxy2 ай бұрын
So this will be a complete clone, vin, vats etc will all be cloned
@markdasparkauto17802 ай бұрын
Yes sir
@kennardhaywood71002 ай бұрын
I have a 2004 Honda Accord. Can I do the same process with a used ECU ? I know the part numbers have to match.
@markdasparkauto17802 ай бұрын
@@kennardhaywood7100 yes just do PCM replacement and forward the steps
@kennardhaywood71002 ай бұрын
I have been reading that I must also replace the immobilizer with the one the used ecu comes from. Is that true?
@markdasparkauto17802 ай бұрын
@@kennardhaywood7100 no
@kennardhaywood71002 ай бұрын
Thank you for all of your assistance.
@markdasparkauto17802 ай бұрын
@@kennardhaywood7100 you're welcome
@kiddynamite27853 ай бұрын
What model autel is that
@markdasparkauto17803 ай бұрын
@@kiddynamite2785 Autel ultra
@asakiaog74633 ай бұрын
Boss hw do I contact you? I need help
@markdasparkauto17803 ай бұрын
I'm in New York Brooklyn New York
@MrErbolius4 ай бұрын
What about new vgs tcu?
@markdasparkauto17804 ай бұрын
I don't think it is supported yet.
@MrErbolius4 ай бұрын
@@markdasparkauto1780i mean not used tcu from 2007 cars?!)
@markdasparkauto17804 ай бұрын
For what ECM?
@rockyboss274 ай бұрын
Hi plz need ecu pinout help me
@autopurlieu4 ай бұрын
Do you have that 120ohm connected In between?
@EdAguirre-zf6lg4 ай бұрын
Ohhh
@canerkukisi75815 ай бұрын
if I use a used esl from another car do I have to reset it first and then write to the new one
@VaneyKromah5 ай бұрын
My own not😢 rising
@АнатолийР-с7з6 ай бұрын
Спасибо
@markdasparkauto17803 ай бұрын
You are welcome
@EmirBeklija6 ай бұрын
Hi i am trying to do same Thing on x trail t32 1.6 dci ecu edc17c84 but i got error 22 with autel. Why i cant change vin
@markdasparkauto17806 ай бұрын
Year
@EmirBeklija6 ай бұрын
2016 car is running normal but i need to change vin only, do you have fb or whatsappž
@markdasparkauto17806 ай бұрын
I never did 2016 Nissan VIN change yet but I did a 11 a few days ago probably need a programmer to do that on bench.
@akchicago3276 ай бұрын
Thank you 🙏
@markdasparkauto17806 ай бұрын
You are welcome
@АнатолийР-с7з6 ай бұрын
Спасибо
@markdasparkauto17806 ай бұрын
No problem
@kva_powerup6 ай бұрын
Hello, will this process work for the vgs3nag2 ???? I have tried the launch padvii and it doesnt support clone for the vgs3nag2 only works for vgsnag3
@mohbel65157 ай бұрын
Hello, what do you need the x431 key programmer for?
@mohbel65157 ай бұрын
Does it also work with diagzone?
@kva_powerup7 ай бұрын
Hello, i tried to erase my eis for w204 mercedes benz 2010 4matic on the platform mode but it keeps telling me failed to erase please try again, please help me
@markdasparkauto17807 ай бұрын
When you hook it up does it communicate
@kva_powerup7 ай бұрын
@@markdasparkauto1780 yes it does and reads all details , but when I try to erase it says failed to erase please retry
@braddean61807 ай бұрын
I have 2005 pathfinder I just got, has no spark no injector pulse, but does prime /run the fuel pump. I disconnect cam sensor ,makes no difference. Also no codes come up.
@kva_powerup7 ай бұрын
I tried to connect, and it says " failed to enter the service mode , please whats your advice ?
@markdasparkauto17807 ай бұрын
You got to check your can bus wires the 6 and the 9 could be confusing so switch it around and see
@kva_powerup7 ай бұрын
@@markdasparkauto1780 I inter changed them and still thesame , on my wire the 9 has a little dash sign under it , so basically I did it right
@kva_powerup7 ай бұрын
@@markdasparkauto1780 please help me out, I really appreciate
@kva_powerup7 ай бұрын
@@markdasparkauto1780 hello, please your response will be much appreciated
2 ай бұрын
@@kva_powerup Hi, did you solve the problem with the IMMO plus and the VGS3NAG2 plate?
@eclipze9507 ай бұрын
Will this work on dodge
@markdasparkauto17807 ай бұрын
Yes it could depending on what year
@nadeemshaikh24367 ай бұрын
Scener model name
@markdasparkauto17807 ай бұрын
Autel elite
@brayandiaz11197 ай бұрын
Really it no burn the bcm
@markdasparkauto17807 ай бұрын
No that call is not on the list.
@ShaheehAlJazeerra8 ай бұрын
BEAUTIFUL JOB AND THANK YOU WE HAVE LEARN LITTLE BIT VERY NICE HOPE FOR MORE REGARDING A MERCEDES CAR TECHNICIAN.
@markdasparkauto17808 ай бұрын
Thank you 👍
@vitorpaulo37009 ай бұрын
To precisando de um arquivo desse bom,vc teria pra venda??
@markdasparkauto17809 ай бұрын
No I don't have any files.
@train49059 ай бұрын
Exellent job,that clip was nifty too
@train49059 ай бұрын
Exellent😊😊
@dellc15219 ай бұрын
Will this work on 2017 navara
@markdasparkauto17809 ай бұрын
Is that car gas or diesel we do not have that car name here in the USA. start with engine size.
@renanpatolilic73089 ай бұрын
Big help.thank you, i have the same problem, car stay in workshop for couple of months now because of this problem
@markdasparkauto17809 ай бұрын
You are welcome my friend.
@renanpatolilic73089 ай бұрын
@@markdasparkauto1780 i open the front timing cover an hour ago, and fuck sick! You're right the engine is out of timing! Need to change the timing chain set.. i almost replace the ecu...thank you soo much.
@delarocamario9 ай бұрын
my fri8end you are a good me3chanic, you the best
@АнатолийР-с7з9 ай бұрын
👍
@macwilson21349 ай бұрын
Will this work if they are smart keys?
@markdasparkauto17809 ай бұрын
Yes depends on the year
@macwilson21349 ай бұрын
@@markdasparkauto1780 it’s a 2010 pathfinder.
@markdasparkauto17809 ай бұрын
2010 Yes ID the car and follow the instructions
@486hfaisal9 ай бұрын
Which key did you use?
@markdasparkauto17809 ай бұрын
Dealership keys only .
@damianjones65469 ай бұрын
I have the same problem with a 2009 Pathfinder I have just bought. So will I need to change the timing chains?
@markdasparkauto17809 ай бұрын
You got to do a complete timing job and you will good.
@damianjones65469 ай бұрын
Ok, not sure if I can do that myself. Never done anything like it before. @@markdasparkauto1780
@thebiggerman697510 ай бұрын
It would be nice to know what you have for a scanner and slow down a so a person unfamiliar with the procedure can follow along Bing bang boom ,whats the rush .
@markdasparkauto178010 ай бұрын
Autel ultra
@LuisGonzalez-kv1jp10 ай бұрын
It was useful for me, thank you very much!
@markdasparkauto178010 ай бұрын
You are welcome glad it worked out.
@elesjuan10 ай бұрын
Hey Brother. I bought a 2007 Xterra with a crank/no start condition the previous owner replaced all of the cam/crank sensors and still doesn't run. He did the timing chains guides and tensioners about 20k miles ago, then left him stranded at work one day. Haven't tested the injection yet, but know for certain there is no spark. I can hear the fuel pump running and smell fuel when cranking, confirmed no spark and has no codes, cranking sounds like has compression. Does it matter which cam sensor I disconnect for this particular test to make it run? Anything else that would cause a crank/no spark on these VQ motors I could've overlooked?
@markdasparkauto178010 ай бұрын
When you read the data from the old one you should save it then you load the data on the new one and then you write it to new TCM. I use autel for this programming its much easier with autel.
@kva_powerup6 ай бұрын
Does this work for vgs3nag2? If no then what can I use to clone vgs3nag2???
@roby1108710 ай бұрын
Hey, I have the same tool but can't figure out how to write the data from the old tcu to the new one. I bought a second hand gearbox with the same part number, I went to erase gearbox and now I have the personalised and activated NO. But when I click load and select old filed it doesn't do anything. Can you tell me what I need to do next. Tia
@princeoffame10010 ай бұрын
where in Brooklyn is your shop need mine done getting a P179C96
@markdasparkauto178010 ай бұрын
Atlantic avenue
@princeoffame10010 ай бұрын
@@markdasparkauto1780 atlantic and where
@kareemroyal86310 ай бұрын
Where are u located
@markdasparkauto178010 ай бұрын
Brooklyn NY
@KhaledBeatz9211 ай бұрын
do you have to save the TCM data from the old trans module first to write into this one?
@markdasparkauto178011 ай бұрын
Yes I had that data backed up from the old original one that I had save.
@weLovePunjab5 ай бұрын
What to do if the old one is completely dead 🤔🤔
@adesokanazeez351611 ай бұрын
Thank you for the information! Do connect k1 and k2 adapter?
@markdasparkauto178011 ай бұрын
You do not have to connect the k1 and K2 but in my video I did not connect the K2 but if you want you could connect it . but I did not use K2 and it still communicate.
@adesokanazeez351611 ай бұрын
@@markdasparkauto1780 thank you for responding
@chemamlopez837811 ай бұрын
Hello, I was watching your video and I have a similar problem, when I bought my car I didn't know that they changed the computer and now that I need to do the emission test the vin doesn't match do you think you can help me with that? How can I contact you?
Question I was doing Sam thing today same car but got stuck when doing key session it would ask me for a mobilizer pin before entering the fob key into the slot , what I’m doing wrong or what happened
@urmechanic6194 Жыл бұрын
Good video my friend perfect
@markdasparkauto1780 Жыл бұрын
What I realized in some autel 's it l does not do automatic pin code calculation on some cars . All you should do is i d the car and going to NATS.
@markdasparkauto1780 Жыл бұрын
What kind of autel l are you using
@mhlolothemba5101 Жыл бұрын
Good day brother, can I use the LAUNCH MCU 3 Adapter on my Thinktool. They look similar