Yeah definitely leave the huge gaps all around it for water to make it's way into your house
@jaimethibodeaux68446 ай бұрын
You skipped over the biggest issue I have -removal of the siding without damaging
@no-pestvent48976 ай бұрын
Hey Jaime, if you are going over existing siding with the wide mount vent cover, removing siding is not necessary. If its an existing vent simply reuse the hole that is already there, if its a new vent being added just drill through the siding and wall with a 4 inch hole saw. Then seal around the dryer vent with silicone after its installed. Hope this helps with any confusion!
@jaimethibodeaux68446 ай бұрын
@@no-pestvent4897 we were thinking silicone too… thanks!
@akbychoice5 ай бұрын
Holesaw used in reverse on plastic so it doesn’t grab and destroy the siding.
@airdaff497321 сағат бұрын
@@akbychoiceOuch! I tried doing it in reverse by holding the blade instead of the handle and I cut myself!
@jferggi4770 Жыл бұрын
The sheet metal duct was delivered all bent up as well as the box it came in. Can not keep it together. Wondering if I can use the old duct that's already there?
@rkgsd10 ай бұрын
If it fits over the old duct, there's no need for the tube. Personally I would've demanded an exchange since the package and contents were abused.
@scottr8360 Жыл бұрын
Idiots forget to mention the part that also came with it.
@lkw5699 Жыл бұрын
I hate the cheap sheetmetal duct. It came apart never regained its original shape. Rigid duct for me
@mahto542 жыл бұрын
You need to caulk where the pipe goes thru wall. Bugs will get in there easily!
@Hvnshlpr2 жыл бұрын
how do you install it when one purchased it with out a tube?
@idyh83912 жыл бұрын
how do you keep the flap from banging in the wind?
@p-tecproductsinc.35132 жыл бұрын
It may be a detail related to the install such as not being slightly inward at the top to nor allow the magnet to attach to the bearing. Or the attachment screws are over tightened not allowing door seal against the mount. It could also be caused by air infiltrating the home at another location which creates an internal pressure, and the No Pest Vent becomes the relieve valve, then the gust of wind catches the door and lets quickly close again. You can give us a call if you have any addition questions, and we will try to help you. Thank You, Kelly
@percyfaith112 жыл бұрын
And rot your roof and attic with all the moist air being sucked back in through the soffit vents.
@normanwells27553 жыл бұрын
Don't bother if you came for any special instructions for stucco.
@JCraftvfx3 жыл бұрын
just install this last weekend and the metal tube disconnected from the plastic housing, not a very secure system. Now I'm having to find myself climbing up back into the attic to fix it. Reason I even noticed was when I turn the fan off I the bathroom there's a noticeable clicking sound from outside, the door flap closing. I wasn't hearing that anymore, so I check and sure enough....yep, came undone
@tvrpaul712 жыл бұрын
I spoke to No Pest Vent about that with the tube and asked them if there would be a problem with putting some glue around the vent and they said no
@davejohn2554 жыл бұрын
Thanks
@jerseyjim90924 жыл бұрын
Will the face place mount over an existing flange?
@greybeardnharg39924 жыл бұрын
This doesn't include the full installation for the J-Block. If you bought this one, and are wondering what the fourth piece does, check out the Lambro Industries installation videos. The fourth piece goes on the inside of the installation. And, yes to the caulking as well.
@olypen86885 жыл бұрын
Exactly what I needed to install vent properly. Thanks.
@LockSportsman6 жыл бұрын
Wouldn’t you also want to use some type of sealant around the top and sides of the wide mount if mounting it directly to the side of the house without the flange?