2:06 I had no idea I could have the build plate move lower than what it auto detects as "home" position and so my Anycubic wasn't levelling properly. I hit that down button a couple times, fastened the bolts and got an incredibly good print at my first attempt. Thanks!

Any idea what size hex bit I need?

Very comprehensive, nice work!

I need a resin that forms a hydrogen bond like glass and water for a medical device I'm developing. This is what causes capillary action. Does anyone know of one?

there seems to be a secret sauce whe nit comes to it because I've had my anycubic photon mono x 6ks for half a year and only know is leveling the plate becoming an issue. It's been a week and still no dice

What size cam locks did you use?

Hi, there! Do you know the measures of the 'hard' part of the trek50? I know for the lengh it's 22'. I really want to buy it, but want to be sure it will comply with carry on requirements (if not full, of course) - 22 x 14 x 9 inches. For the lengh it's all good, but not sure the other dimensions..

We're did you get the a frame awning

perfect.. hopefully you put out more content

great tutorial, i have been searching for a tutorial that is not explaining at the speed of light with an accent that I have to decipher .

GRATKIT nor GATkit like write ....

Finally, not an annoying Indian talking.

So, there is no diference between the man and women one? Just 5l? The rest is the same? Thanks for the review!!

Alright, thank you for answering my question "do I need Tough Resin?" that quickly. I print a lot with standard-Resins, and know how "easily" these parts can break, / literally shatter 😬

When you smell it, then your respirator is bad or your ventilation setup. No smell doesn't mean that it doesn't harm you inhaling it, it just makes it more dangerous 🙄🤦‍♂

Hey I don't know if you read this comment 2 years later. I replaced my LCD screen and then tried it with the UV test screen. It seems to work for about 2 seconds and then the UV light seems to dim down. I double checked the connection but everything seemed fine?

Have you noticed a smell difference? I really wish companies would give us exact chemical composition so we know what's in it just like how FDM is sold. I swear to god most resin companies secretly mix their standard resin and elastic resins in different ratios for different toughness metrics and just call it a day after marketing it as different.

Excellent session. It is explained with simple language. Thank you.

How does this resin handle detail?

Towards the end of your video when you are showing the reflective panels, there is a black hanging 5 tier pouches attached to the wall for some small storage. It looks like they are connected by rings. Could you please share where you purchased it. Thanks

Wow bro, this was short, sweet and to the point. Thanks to your video, our vacuum brush is operational again. Greetings from the America of Europe (Switzerland)!

I'm missing a github example project, but the explanation is very clear thank you.

does it work well for scale model cars 1/24? I wanna details and strongness :-) my anycubix is ms5 Pro

very helpful video 👍 with exchanging the belt on my D6

Thank you. Very helpful. Greetings from Germany. 😊

So for my Photon original, just like this one, I have not tuned it. Since replacing the factory FEP I've gotten mostly failed blobs stuck to my FEP. This is the one detail I have not considered, would a FEP too loose cause that? Cause I'm pretty sure I'm undertightening as I'm tightening about a half to full turn past hand tight. Basically enough that resin stays put without seeping under the rim.

Bought a new motor and it wouldn’t work. Where do I go from here?

Hi, great video. How much is the diameter of the o ring?

My fep wont get to 333, stuck around 175hz and i run out of turns on the bolts. Any ideas?

I hope I don't sound cocky, maybe you don't really care about all those details and in that case enjoy your printing time and ignore all this ! but if you do want to overcome your problems read this: your settings and the way you print your models are all the reasons why you have those problems, the fuse of parts is due to the over curing of the layer bcs it was on the bottom layers, you need to raise the model and print it on supports, for the bar, it's beceause your fep stretch out your piece when it the build plate goes up so it ended up crooked, you should never print flat on your build plate or you'll end up with bending, torsion or failure at worst.

The music stopped me hearing clearly, some of us find it distracting

🛒🗑🗑

thank you but audio is so so low that it is hard to watch/listen/understand

so what do i do if i did break the ribbon wire connector

Hi. i changed, but its not working. Any idea?

What is the app net

It is importatnt to make sure the side-brush module is fully depressed into its cavity (by keep one finger pushing hard down on it against the springs) whilst you are screwing it in.

thanks for the idea

Now I know that these small rectangular rubbers are actually not for chockabsorbing! They are protecting the wires as you can see in this link: kzbin.info/www/bejne/haLKdWqwqt5_q6M" at 9minutes in to the movie!

Soooo helpful! My hero!

Does it chalk or powder up when parts are rubbed against each other?

Hello, thank you for the video. I managed to replace the O-ring and the cleaner is working. 2 rubber rektangulär rubbers size:10x7x5 mm fell out when disassembled, Cannot find any place for them!? Anyway, the machine seem to be working without them. Do you or somebody else have any idea where to put them?

So many great ideas! ❤ Thnx.

Don't do what I did... trying to do this from memory without rewatching the video, I tried to get it to the right frequency without attaching it to the vat first. Ended up stripping some of the frame screws and not getting it up to the right frequency still. Wish I had rewatched it. =) The video was really clear and helpful, after I followed the instructions correctly it worked great.

It's not working anymore, do you have another suggestion?😊

Thanks for making this video its such a lifesaver, didn’t want to end up buying a resin that would break easily

Watching lots of water washable vids. No IPA is a big bonus for me, chemical sensitivity has made me avoid resin crafts. This clear resin would be great for aircraft canopies, headlight lenses etc. 3D printed optics like light pipes?

Works perfectly with spectroid. I did 333Hz. every other method failed for me.

what is the app name

A lot of good ideas especially for storage and the rod for hanging the containers and chothing. The biggest complaint I have with my soft sided PUP is the ability to dry clothing inside and ez acess to storage.