Пікірлер
@ragercrepair9301 Күн бұрын
That should help with cutting Chambers!
@BuckYaSaws Күн бұрын
@@ragercrepair9301 spot on, should work out good. I just need to drill the backing plate for the 4 jaw and make a plate. That skinny one should be handy for making small bushing ect.
@ragercrepair9301 Күн бұрын
@BuckYaSaws I think you'll find that skinny one will come in handy for all sort of smaller stuff. Especially for making say a 12mm to 10mm wrist pin bushing with a collar on it. That's where I need to update mt lathe period.
@BuckYaSaws Күн бұрын
@ that’s exactly what I wanted the skinny one for. This kit was 30$ish.
@ragercrepair9301 Күн бұрын
@BuckYaSaws that's a great price. Let me know how they work. I'd like to get a set if they're decent quality.
@BuckYaSaws Күн бұрын
@ I’ll keep ya posted.
@RichFife 3 күн бұрын
Fun little bikes!!!
@BuckYaSaws 3 күн бұрын
@@RichFife some times I have more fun on the little bikes and quads.
@RichFife 3 күн бұрын
@BuckYaSaws 100% I like the 450f, it's work and has stupid power... but, the smaller bikes, you can toss them around, rip around, and have fun with them anywhere.
@BuckYaSaws 3 күн бұрын
@ same here, I got a kx450f & love that stupid power. But your spot on, can’t beat them little guys for around the yard shenanigans.
@Sinarglondong 5 күн бұрын
Very good ❤❤❤❤❤❤
@adrianstefan23 7 күн бұрын
👍🏻👍🏻👍🏻👍🏻
@adrianstefan23 7 күн бұрын
👌👌👍🏻👍🏻
@chrisaker25 7 күн бұрын
What kind of video is this...wtf are the screw adjustments for mine to sound like that???
@BuckYaSaws 7 күн бұрын
@@chrisaker25 it’s just a short clip of the saw idling. To get yours to sound like it you need to mod the muffler, the carb settings won’t really help you. The carb setting are set to my saw mods, altitude, ect…
@TravisDoesFirewood 10 күн бұрын
What a beaut!
@BuckYaSaws 10 күн бұрын
@@TravisDoesFirewood she is getting there. Thanks man!
@daninuesca3801 10 күн бұрын
Looks good buddy! Just subbed from Maui!.. ALOHA!..🫡👍🤙🏽
@BuckYaSaws 10 күн бұрын
@@daninuesca3801 thanks man! Maui is a beautiful place
@ragercrepair9301 14 күн бұрын
These are one of my favorite saws to fiddle with because they are so easy to tear apart and modify. If you screw up, cylinders are a dime a dozen!
@BuckYaSaws 14 күн бұрын
@@ragercrepair9301 i agree it is pretty easy to work on, i like them.
@Houseworksaws 9 күн бұрын
Those open port 45mm that came on the 51 I think .. Those run really good after some work. They have nice small chambers and wide bands . Throw some hot numbers in em and a good set of fingers in they’ll rip. Fun to play with and experiment on.
@ragercrepair9301 9 күн бұрын
@Houseworksaws I completely agree! Getting the torque to stay with the higher rpm is harder, but it is possible!
@BuckYaSaws 9 күн бұрын
@@Houseworksaws not running bad for the 44mm open port. Cut the base and move the ports some.
@Houseworksaws 9 күн бұрын
@@BuckYaSaws no man not at all it sounds great. On those I’ve found the key to Torq but still spin the chain is keeping 2-210psi with like a 98 roof. Around 120 transfers and 78 intake. They wake right up
@REpowersaws24 14 күн бұрын
There's a radical 50 build in one of my shorts. Not my build, but a blast to run
@ragercrepair9301 14 күн бұрын
@@REpowersaws24 she's runs good too! Just watched it. It's the short on the very bottom of his list of shorts.
@REpowersaws24 14 күн бұрын
@ragercrepair9301 yes sir! She's got plenty of secrets under the hood
@ragercrepair9301 14 күн бұрын
@REpowersaws24 you'll have to jump on my page and check out both of my 55 builds. They are pretty angry little shits.
@TravisDoesFirewood 10 күн бұрын
I love what you can do with saws, keep cuttin' brother!
@ragercrepair9301 14 күн бұрын
Running pretty darn good! I really love the 55 chassis. I'm kist searching for the best performance and making it so most anyone can do it. Someday I'll end up with an easy mod that works well that anyone can do!
@BuckYaSaws 14 күн бұрын
@@ragercrepair9301 thanks bud! went back in and cut the base & tweeted the porting. 105,119/122 & 78 with .023 squish. Still rocking the stock carb for now, have a 372 carb sitting here but need another top cover. I don’t want to drill that old one for a v stack setup 😂.
@ragercrepair9301 14 күн бұрын
@BuckYaSaws I'm looking at using the 365 intake and air filter. I'm hoping that fits under the cover with little to no mods.
@ragercrepair9301 14 күн бұрын
@BuckYaSaws I would try getting that exhaust to around 102 or so. She will spin a lot higher rpm! Also if you cut about half the key out of the flywheel to advance the timing, you will see and incredible increase in cut speed and power!
@BuckYaSaws 14 күн бұрын
@ I was aiming for 104 but getting light at 105. Was going to do the timing next.
@Philjr-h7j 14 күн бұрын
Sounds good great job on the work have a great weekend and happy New Year send some more videos enjoy watching them
@BuckYaSaws 14 күн бұрын
@@Philjr-h7j thanks man! Enjoy your new year as well.
@Mainelyoffgrid 16 күн бұрын
Whats the best modification i can do to my 462c.... great videos. Subscribed
@BuckYaSaws 15 күн бұрын
@@Mainelyoffgrid thanks for the sub! Normally the best simple things you can do is muffler mod & or better air filter, max flow or something similar.
@coxsaws 16 күн бұрын
Nice
@ragercrepair9301 16 күн бұрын
Looks to be running rather well
@BuckYaSaws 16 күн бұрын
@@ragercrepair9301 did a mild lung. But I think it does run well where it sits. Just need to run some fuel through it now.
@BuckYaSaws 16 күн бұрын
@@ragercrepair9301 thanks man
@SomeGuysSawShop 16 күн бұрын
Seems pretty decent
@BuckYaSaws 16 күн бұрын
@@SomeGuysSawShop ya I’m happy with how it turn out.
@SomeGuysSawShop 16 күн бұрын
@ it’s definitely no slouch
@alexbrown5229 17 күн бұрын
How did it run
@BuckYaSaws 17 күн бұрын
@@alexbrown5229 runs well with this setup.
@ragercrepair9301 18 күн бұрын
That's running damn well! Good work.
@BuckYaSaws 18 күн бұрын
@@ragercrepair9301 I did a mild lung intake on it. 102,120 flat and 78 with .028 squish. Runs decent. I’ll post the vid of the port work soon.
@ragercrepair9301 18 күн бұрын
@@BuckYaSaws those are pretty good numbers. Remember, you can lung it pretty much all the way to the piston skirt. That helps a lot with intake open time. Just leave enough room on the table so your rings don't ever have a chance to drop into the intake at BDC. I think it's running very well. That's a fresh cylinder with new rings correct?
@BuckYaSaws 18 күн бұрын
@ yes fresh p&c with 2 heat cycles before the video.
@ragercrepair9301 18 күн бұрын
@@BuckYaSaws also if you get that squashed down to about .020 4.022 that will help with your compression in a little bit of torque. Just keep that in mind as you're navigating trying to get the best performance out of that girl. I will say that thing is running very well, and once you get it broken in it's going to be even more powerful.!
@ragercrepair9301 18 күн бұрын
@@BuckYaSaws she's not even close to broken in yet. Lol.
@Paul_Gale 18 күн бұрын
nice, she rips sounds like its in its happy place.
@BuckYaSaws 18 күн бұрын
@@Paul_Gale thanks man, ya it seems pretty happy.
@SomeGuysSawShop 19 күн бұрын
Dude clean work man, it looks great
@homopit42 19 күн бұрын
Nice cylinder and nice port work! I wish I have a lathe to experiment with some cylinders I have (mostly old Husqvarnas 61/266/272).
@BuckYaSaws 18 күн бұрын
@@homopit42 thank you! I recently bought the lathe from my neighbor. I got to add more Husqvarna to my collection, only have a 50 & a 272.
@Wrensspeedshop 21 күн бұрын
Clean setup buddy. Keep up the good work, ready to see the process on this. This would be a blast a racetracks running around the pits. May want to try to plumb some of your vacuum lines to the intake port/filter. That’ll give you vacuum and not force pressure into the crankcase.
@BuckYaSaws 21 күн бұрын
@@Wrensspeedshop Thank you! Thanks for that carb tip! That’s my next step plum the vent lines. Deff my first time trying a blow through carb.
@theoldfellaDigwell 21 күн бұрын
Tried doubling up on Cloggin Block Got a Terrific Kick
@ragercrepair9301 22 күн бұрын
She's cutting great! I think you'll see a huge increase if you open up that muffler. It sounds like it's struggling to breath up high some.
@BuckYaSaws 22 күн бұрын
@@ragercrepair9301 yo man, thanks! it’s pretty open. trimmed the baffle, added a 3/4 pipe and open the stock hole a lot.
@ragercrepair9301 22 күн бұрын
@BuckYaSaws where is your intake at?
@BuckYaSaws 22 күн бұрын
@ 76* but it’s running a aftermarket carb. Was the best of the 3 carbs i had.
@ragercrepair9301 22 күн бұрын
@BuckYaSaws ahhh I see. Try a lung in the intake towards the skirt of the piston. Then adjust your intake timing to approximately 78 degrees. I think you'll notice a huge performance up high and a lot more torque. It doesn't sound like it has a lot of exhaust, but that can be caused if it doesn't have quite enough intake too
@BuckYaSaws 22 күн бұрын
@@ragercrepair9301 I like your thinking, my plan is to get the carb dialed in & put some time on the new piston & cylinder, then I’ll go in and lung it & set it to 78*
@BubbasBirdWatching 24 күн бұрын
Cool build dude!
@HayChaffandSawdust1 24 күн бұрын
Sweet!
@TravisDoesFirewood 26 күн бұрын
Beautiful!
@coxsaws 26 күн бұрын
Sweet port work 🎉
@Houseworksaws 26 күн бұрын
I bought a “GardenPal” brand cyl $ piston kit off Amazon for 45$. It’s as nice or nicer than oem. I was blown away at how nice the plating, chamfering and port shapes are for under 50$ shipped to my door in 2 days. I think they make a 461 kit as well as some others no one else makes typically. They even make a 2100 top end kit.
@BuckYaSaws 26 күн бұрын
@@Houseworksaws hell yea man, I’ve seen that brand before. Think I have some stuff from them. I have another amazon piston and cylinder coming up for the 460. Wild how some of the stuff is super nice for super cheap.
@ragercrepair9301 26 күн бұрын
Looks good. Should make for a much better running saw!
@BuckYaSaws 26 күн бұрын
@@ragercrepair9301 thanks man, going to fire it up later today. Doing the muffler mod now.
@Houseworksaws 27 күн бұрын
Man those milling setups have built a lot of stuff over the last 100 years. Many times that’s all a guy would have in his home workshop. Great lathe setup you got there and an even cooler project.
@Houseworksaws 27 күн бұрын
Man looks like my bench. I have all the same carb tools including the green pump. I use that lil green pump to do most of my pressure testing nowadays. It’s always within reach so instead of dig out my mighty vac I grab that. I’ve got a crap load of time on that lil pump and it’s treated me right especially for 15$ back when I bought it 2-3 years ago.
@BuckYaSaws 27 күн бұрын
@@Houseworksaws going to try that carb swap you recommend for the 036. Thanks man!
@Houseworksaws 27 күн бұрын
@ it takes a lil work and fitting but it’s a great alternative especially if you wanna keep choke and air filter.
@BuckYaSaws 27 күн бұрын
@ I got a spare carb to take the shafts from, itching to see the increase.
@Houseworksaws 27 күн бұрын
Success! Nice work
@BuckYaSaws 27 күн бұрын
Thanks man! Used your tip to anneal it before threading.
@BuckYaSaws 27 күн бұрын
Thanks man! Used your tip to anneal it before threading.
@ragercrepair9301 27 күн бұрын
Should be a nice runner once it's ported!
@BuckYaSaws 27 күн бұрын
@@ragercrepair9301 will see how it turns out, my first 461.
@ragercrepair9301 27 күн бұрын
@BuckYaSaws I think you'll do well. So far your builds are much better than stock. That's always the goal right?
@BuckYaSaws 27 күн бұрын
@ your right, better then stock for the most part haha.
@ragercrepair9301 27 күн бұрын
@BuckYaSaws all the saws I've seen you build have been better than stock. That's everyone's goal! Regardless if the power is 10% over stock or we'll over 100%. A gain is a gain so you're winning.
@jimssawsnstuff8903 28 күн бұрын
Cool, which brand? Those are key things you mentioned. If plating handles port work, the timing numbers are very decent, not excessive casting flash, then it’s a good buy. I like that the cooling fins are very similar to OEM…some are so think they have a very heavy look and feel bs OEM.
@BuckYaSaws 28 күн бұрын
@@jimssawsnstuff8903 thanks Jim! It’s Mtanlo brand. The plating held up fine to the porting, I’ll post the video tomorrow of the port work. The flash wasent to bad, just a little more then the oem 461 cylinder. I plan to do a long term review on it to see how it holds up.
@jimssawsnstuff8903 28 күн бұрын
@ sounds good! I’ve used that brand too, just not for cylinders yet. It was such a scramble up here with the postal strike, really limited options. I’ve found opening the Lower transfers and some slow work sure helps the 461’s
@matthewknight5641 29 күн бұрын
pretty awesome man. i hope you follow thru with this build even tho its gonna be a lot of unexpected challenges.
@BuckYaSaws 29 күн бұрын
@@matthewknight5641 ill get it done one way or another. In too deep to quit.
@matthewknight5641 29 күн бұрын
@BuckYaSaws it's for sure gonna be a one of a kind build. I'm excited for you bro.
@ragercrepair9301 Ай бұрын
Seems to be running pretty good.
@BuckYaSaws Ай бұрын
@@ragercrepair9301 I think so, did a small change. Need to work on the carb, acting funny. Might swap it to something bigger.
@ragercrepair9301 29 күн бұрын
@BuckYaSaws what size carb can you bolt on that without a lot of modifications?
@BuckYaSaws 29 күн бұрын
@ going to look into it, haven’t really did any carb swaps on a 036 yet. Probally start with a 440/460 carb
@ragercrepair9301 29 күн бұрын
@BuckYaSaws that's what I'm running on my 55 and they make a huge difference. I think that carb flows very well. The one i built with the 372 carb runs a higher rpm, but has less low end. Makes me think with the 036 being 60 cc it would like the 440 carb.
@BuckYaSaws 29 күн бұрын
@ going to try the 359xp carb swap mr house recommend on this saw.
@TravisDoesFirewood Ай бұрын
Go Tony go!
@TravisDoesFirewood Ай бұрын
I love the sound of your port jobs!
@TravisDoesFirewood Ай бұрын
Sounds meaty!!
@SSRacing66 Ай бұрын
Curious why you didn't cut the lower sides of the piston to let it breath better into the transfers better ? Also, were you able to get your squish down to .020" ? thanks for sharing
@BuckYaSaws Ай бұрын
@@SSRacing66 was going try that on one of my other v modest. Squish I think is around .023 give or take with the base gasket delete. I’m just going off memory, not near my note pad.
@iiredeyeiiredeye1569 Ай бұрын
Sketchy...but cool.
@brainiacproductions357 Ай бұрын
The best chainsaw ever made
@brainiacproductions357 Ай бұрын
hopefully it screams. This is the type of content people like to see.
@TravisDoesFirewood Ай бұрын
Looks like a beast!
@TravisDoesFirewood Ай бұрын
Good setup Tony!
@Houseworksaws Ай бұрын
Man I really hope people can appreciate how cool of a project it is but honestly until you’ve built a stroker it’s not gonna hitcha quite as hard. This project demands way more attention man. Your work on it so far is impeccable. Anyways I just wanted to say I get it. Keep kicking a$$
@BuckYaSaws Ай бұрын
@@Houseworksaws thanks for the kind words man! Your right about appreciating the work that goes into building one. It hit me last week 😂 had to mess with some 4 strokes 😂😂. I think people will warm up to it once it’s running. I appreciate you and the other decent people that regularly comment!
@ragercrepair9301 Ай бұрын
This is getting better and better! Great work so far man!
@ragercrepair9301 Ай бұрын
This is such a cool series build! Good work man