Well, that was scary to watch. Luck and circumstance were on your side. I hope they never run out if you're going to drop trees this way. Seems the tree was just straight enough with a small enough levering branch pulling in your desired direction that allowed it to remain standing while you went almost 80% into the stem with your notch that's also a bit narrow. That's all kinds of dangerous, especially while you force the saw with a dull chain like that. But it's better to be lucky than good, I guess

Be ok if you new how to cut down a tree😂

Thank you. Just what I needed. Saved me $500 in labor costs

How is this repair holding up ?

Thanks man, going to be doing a top end rebuild on 04 360 this summer. Then probably both clutch replacements. Wish me luck.

Hey umm I have the same issue but you went off canmera at the most important part

Just started this job. That socket you're looking for is a 22mm!

Hola 👋 buen día tengo una cuatrimoto Kawasaki lakota y estoy buscando una pieza para la moto la pieza que estoy buscando es arrancador de cuerda o Piola es modelo 95 Kawasaki 300 si tuvieran una pieza que no ocupen que me la puedan vender

0:55 is it oil or cooling water in the container there??

Did that fix your problem

You should not attach it to the trailer because the outside stringer of the mobile home is not supported vertically. The joists in the mobile home are supported further toward the center of the mobile home. The steps and landing are supposed to be freestanding. Another crap job. Thank you.

Exactly what I needed for my Grandmas 2010 Chrysler town and country touring. Alternator went out and the shop quoted $850 to fix it. I told my grandma no way and found a rebuilt one for $150 from a reputable place in town and switched it out in 30 minutes, saving Grabdma $700. Thank you so much

It won't run with that stator.

Would you just look at it?

That's definitely a temporary fix. If it ran after the oil that means it has low compression and needs a top end rebuild

My Suzuki quad 400 King Quad clutch cover will not go back on

I sharpened a curved chisel on my air hammer just took about a minute, then to tighten the new one used the smallest pipe wrench and small adjustable curved pliers and got it tight by using box end of a wrench on adjustable pliers, a 1- 1/2 inch crows foot wrench would have come in handy. metric comes out to 38 or 39mm.

This a good video about how to build a BOMB!!!

Do you stil have that diesel mule? Please holler at me 740 four sis for 5 tree tree oh ty :)

Thank you for the video. I will be doing this to mine. I was confused on which way to turn the cam.

There are a lot of misconceptions on attaching porches to manufactured or factory built homes, in short as I have seen and will be doing myself to my manufactured home, if you support the porch itself properly and attach it to the house it will not settle any more than if the home were to settle naturally anyways. This looks great and would love how you got the gabled roof line even with the existing gable from the home extending out, I see so many of these gabled porches built and they do a horrible job of integrating the shingles in with the original shingle pattern, and the decking is generally lower than the original gable which makes otherwise a very nice gabled porch look tacky and poorly built. Any pointers on that would be great. Thank you for the video!

I saw that!

Would yours just crank so slow that it wouldnt start when hot?

Thanks

Dude the piston on mine came out almost leaking brake fluid and er thing now and idk what to do

I replaced the spring and did a valve adjustment. Valves are in spec but mine still does that problem. It'll crank over with the plug out but if I replace the plug it still won't crank past a certain point. Any ideas?

You retarded the timing. Big no

I have a 1995 seadoo bombardier and i took it to a lake and ran fine then all the sudden it bogged down and won’t go in water but sounds fine out of water. Any thoughts?

I have an l225 and glow plug heat is important even in warm weather

those tractors wont start well without proper glow plug action.

is There some kind of trick to putting that casing back on . Something up around the starter is stopping me from going flush with the motor😊

Install stater

I have the same one and 4x4 switch not workin any solution would help

How do you remove it and clean it?

Thanks for the video. I am tackling the same job today and could not see a good way to take the hose out. I hope a hose place around here can make me a hose after I cut it.

Please help, I need part numbers for rear bearing and seal

OMG !!!!!!! Friggin McGuyver level genius.

I know this is an older video, but what is that lever thing at the mid point of shift shaft? Not all moto 4s have it. If I remove mine I can have all 4 gears. If it's installed, it won't allow enough rearward travel to catch reverse.

Great job.

Valves need to be done when the engine is dead cold

That's how I do it. Except I take a nylon glove and put the electric connector in it so I know it won't ground on me. One of the easier alt. to replace. You did an awesome job with the video!

You are awesome, thank you for the excellent video on window repair!

I was searching for videos on how to remove my fence prior to the arrival of Hurricane Milton here in Florida and I couldn’t find one specific to the fence I have. As a last ditch effort, I tried to search one more time and this video show up !!!! You sir are a life saver !!! Thank you !!

I didn't touch the bottom, pulling the back out first worked the rest 👍

Well done - the lock Tabs will probably be redesigned after you replaced the $60 tool they were designed for - with a $1 baking pan...

Not much point in carrying a spare belt!

Did if flash code 5 ?. Mine quit moving altogether zero movement engine labours in drive and doesn’t even attempt movement

Your video is very confusing because you are all over the place

I have one but it turns over and won't start. Oil good, I got spark and when I spray starter fluid in carb I get nothing.

You kept calling the cdi box the stator ??