I’ve been thinking real hard about getting one of these little welders to play with. I think you might have sold me one 😂

Hi there what is the name of these pins?

😎😎😎😎😎

I had them contact me about reviewing the same welder

Good review..nice welder 4 sure..

Any idea on the amp used on 240v or 220v Input.

It would be a good welder for small infrequent quick welding jobs. The issue with small welders is that depending upon the length of the MIG torch, 6-10ft of weld wire is lost when a new spool of wire has to be loaded. After 10 spools of wire, 60-100 ft oif wire is lost. If someone can come up with a way to join the ends of weld wire, that might be a labor & cost saving gizmo.

Nice

You can buy twist locks like goes on those containers to weld to front hitch inexpensive makes it easier to attach to front just go under it instead of the sides with hitch and it will attach in seconds easy on and off just like the original container chassis. That’s what I made my hitch with and made my tongue longer for turning.

WUT AIR COMPRESSOR R U USING?

Great video my question is what is the smallest collet you have use, I use a lot of 1/8" drill bites and some 1/16" that I need to sharpen.

What about getting replacement grind wheels. I looked on there site but like everything else they sell no parts avalable. You cant call them you have to go through there AI contact thing. I bought there gas powed post driver witch broke on 4th post. When through that useless AI thing an still not fixed

I bought one and it has the worst manual I have read. Hard to figure out how to install the blade, properly tension the blade. Be nice to have some advice on using the right speed. It also does not lock closed so a bit awkward to carry.

Can you provide a list of what tools you used to line bore?

Did you check the initial runout of the chuck body itself. Maybe your front spindle has play in it?

This video might be nine years old but dang I was so pissed off that I couldn't get it to arc thank you so much

Nice. Thanks for the videos.

I have to move a 20 ft container on lot about 50 ft from the front yard to the back yard. I have a proper wheel dolly for the rear end. since this is a one time move I'm thinking of using a chain over my pickup truck ball. do think this will work?

None of those collets look anywhere near small enough to fit a 3mm sized bit in there. In fact they don't even look like they smoothly step down in size. The collet thats in the position for the smallest bits doesn't look like it has the smallest opening. Maybe I'm seeing this wrong.

We have bought some Vevor equipment over the last couple of years. They seem to make good stuff for the price. When we need a mag drill, I am sure we will purchase a Vevor one.

You was fantastic in your instructions on this tool.👍 I just purchased it and was searching for instructions and found yours, I am very happy that I did. Thank you so much for your time showing this to all of us.😉 Mike in Maine

Nice!!

+ Can it run a 6010 rod?

Does it not have a foot pedal for TIG?

Just an everyday diy👍

Young man, thank you for informing me about removing the saw from the base mount . I would have removed the three bolts from the saw. Removing the one bolt at the bottom makes so much since. Thanks again.

Why is some orange and are yellow? Is it the year model or is all 13B the same colors?

Awesome video... thanks for the upload!

When I cut off short pieces in my chop saw or horizontal band saw I weld 1/4" x 2" pieces of flat bar to the edges,,, it makes it much more stable

what happens when it gets older and gives out?

This is exactly the modification I've been looking for. Many thanks for the video.😀

Good job

Their memory walks beside you

First I would like to say you did a good video on this machine. The manual is far from help full. However I must ask as to why there is no mention of a couple items I noticed when I purchased mine. First is that you mention numbers on collet are hard to see but kept in the correct storage place it will be ok. Correct.....however number on collet is reversed from storage tray such as 5 - 6 on tray is 6 - 5 on collet. In addition I do not understand why collet 6 - 5 is the smallest diameter? Well maybe this old man is just confused. Also I understand these "issues" should not affect how the machine works. Attention to detail is good in a product and should be maintained. I will say maybe this confusion / concern is just on my part.

Nice work , look strong enough for commercial use

Great video! Are there any Weldon shank drills that drill out the full hole, to countersink bolts for example?

Terrifying to watch, the way he took off that float he'll be lucky if he doesn't either seriously injure himself or worse still kill himself, doesn't seem to have much idea about operating a dozer.

I got the same thing bought it brand new, it's Crap, Can't see nothing but the sparks...

Thank you dude been at it for 2 hours in 30 degrees outside lol

Does tig requires gas? Or it works like fluxcore?

I’m still using old school Huntsman and a Jackson. Started welding for a living in the early 80’s.

Man thank you so much no really so much 🙏🏼

How does it work with 110V vs 220V, did you get a chance to test it? What would be your recommendations for 110V usage?

As a beginner welder are the settings hard to get dialed in.

And 1 year later the very same jack in over 50% more at $163

Where are the shavings accumulated?

OMG you are a lifesaver!!! Just started welding and could not figure out why this new mig was not arcing.

Glad to see your still here on KZbin 🙂👋

reminds me of those big flat sanders for doing exhaust manifolds.

But a floating tap head for your mill with interchangeable collets. Or a Tap-matic