I need a tcm programmed. Other than a stealership how can I get it done?
@OzMechanics21 сағат бұрын
What car do you have and do you own a scan tool by any chance ?
@quicksno7 сағат бұрын
@@OzMechanics I have a 2008 mazda 6 2.3L. I do have a scanner and got a u0101 as well as a gear ratio mismatch. Also a missing can message code on the pcm. The only thing left to check is power, ground, and can wires. And thanks by the way. I found your video very helpful.
@thewagonadreambylewisКүн бұрын
Lesson learned before buying any car in future… is the car battery easy to get to ??? Lol😂 check under the hood first
@teresalouiseiquilt2525Күн бұрын
This is a great video. Very informative and helpful. Thank you. 😊
@matthewgarner8728Күн бұрын
Thanks man!
@leowilson18372 күн бұрын
Happy birthday🎂🤡
@gilbertoavendano77112 күн бұрын
Yeah right
@squidben57802 күн бұрын
Great video, I thought my alternator was not charging would stay around 12 had to restart the car 3 times before the voltage would go around 14! guess it saw batterie had gone down from me starting the car 3 times in a row before it considered turning up the demand on the alternator. Great and informative video!
@2turntV3 күн бұрын
Quick question What if the air is coming out but it feels like it’s only taking in the air from the outside . Or it’s barely blowing air out . What would it be
@ClaudetteFrye520773 күн бұрын
2008 nitro has been the biggest headache of my life!!! So fed up!
@ClaudetteFrye520773 күн бұрын
What was the 2 wires or did i miss something?
@gregsarro58393 күн бұрын
Dealing with a Nissan rogue 2018 has cel and battery light alternator is good noticed the shutter stays open when starting vehicle so curius can this be the actuator or the shutter also whereby would the actuator be
@MikeConner.akaRadio3 күн бұрын
When you test the ohms you want a reading. No reading or OL means irs bad
@anthonypolo47883 күн бұрын
Oz I thought if the knock sensor read nothing that it is bad I thought It should be around 100-105 ohms????
@zeus_mtz3 күн бұрын
If I clean it, do I have to relearn the idle? Or would the check engine light clear on its own?
@OzMechanics3 күн бұрын
Most Chevrolets would need an idle relearn
@zeus_mtz3 күн бұрын
@@OzMechanics Got it. Would just clearing the check engine light do it?
@sr8shoota3 күн бұрын
My 08 charger has a reservoir in the engine bay to top up fluid . On my 2013 300 I can't find a place to top up the fluid
@TheDavidandre6103 күн бұрын
Should you replace the entire car carpet from coast to coast because of "mold"?
@apb383 күн бұрын
Great video but the only other question I would ask is how much did you or would you charge for this service cause I have the same problem.
@Shootingstarcomics3 күн бұрын
I hate this design. I just made a little shim but because I thought the problem was with the metal but next time I change the battery I’ll just throw the plastic away.
@EMVelez3 күн бұрын
Not sure how this was supposed to help
@OzMechanics3 күн бұрын
This is a short to the actual video that’s jammed packed with a lot of information
@OzMechanics3 күн бұрын
Link of the full video is on the pinned comment
@GRRN994 күн бұрын
Dude…fuck I’ve been looking and looking for a draw in power from my car and I seen this and checked and my has water but the 40amp fuse is busted..the relays are good..so the corner of my cover is broken right where the 40 amp is I am hoping the water just got on there and popped it..going to get a new one tomorrow
@juliansdiamonds4 күн бұрын
Your sharp as hell !!!! Good work !!!!!
@jgt93385 күн бұрын
Which model of Autel scanner is that?
@genedumion35885 күн бұрын
Frank I love you :)
@locotico715 күн бұрын
Great video. Great instructions
@user-md2zq4bf5x6 күн бұрын
How do I find one of these
@JoseSandoval-ic5xe7 күн бұрын
Hi I'm sorry for the question I'm trying to figure out if this is my problem have changed so many parts, did you feel like car had no power or will not really accelerate with rough idle? Feel like I have no lower rpm torque like before that had been getting worse with time. Plus towards the end when you explain that it will catch it feels like that ill be driving and rpm gets stuck like if I had cruise control on but at like 20 mph I then flip the gas pedal and it gets unstuck.
@davidhinkle22077 күн бұрын
The ones that know what they are doing won't hit it that hard it don't take much. Sounded like it would die in a few on its own.... I assume that trick will work for most makes.... Thank you for the tip.i will be trying it on my 1999 astro. Tomorrow.
@knockywigglesworth19097 күн бұрын
Reset adapteive learn with high end scan tool.or forscan.
@marymcd69978 күн бұрын
What would be solution for 2015 Duster Fuel Gauge showing empty.?
@bird2can3488 күн бұрын
Supp Oz , yea Scanner Danner is a great teacher. He says look for Heat and vibration and leave it alone! Shout out to you as well I learn a lot from you as well. Can’t forget my guy Erik from advanced level.
@krazytyler33668 күн бұрын
I got a question. I just replaced my cam sensor (bank 1) on my Nissan Pathfinder 05 and the code is still coming up. What possibilities do you think it could be? Connector? Wiring? Defective part or maybe something else? Because my car starts fine and runs, just bugging that I can't find the root problem. Thanks for the video, gave me more insight!
@TurnThemWheels8 күн бұрын
Yep, has to be in D
@fatherguidosarduchi52049 күн бұрын
I found this video refreshing. Finally a real mechanic. The dealerships have trained techs. They only learn from books without much hands on. Good mechanics cross train on everything and need to know how to read the engine and vehicle systems. Dealership techs just roll parts onto the car until it runs correctly again. This man knows his stuff and I’m so glad to see someone like him out there. Question for him though. Do you or have you gone to the smaller hole rockers that Chrysler updated for these engines? They did this to help remedy the rocker from rolling out of position when the lifter collapses or breaks an internal spring. Lots of times when the rockers rolls out the lifter does also and can wreak havoc with the valve train.
@candeffect9 күн бұрын
Watch the talking hand.
@gordonfuentes8089 күн бұрын
brada its so ez 2 replace a blown fuse😂 but wut u did wuz moa den jis a mechanic u went above n beyond 2 find da cauz or issue y dat fuse wuz blown😳 very eduacational😎 awsum job wel done 💯🤙🏾✨👊🏾👌🏾💣💪🏾
@joedirt17129 күн бұрын
Thank you for your time.
@rafaelmartinez69109 күн бұрын
Oz i want to send you a customer who probably needs the Reprogramming the ecm to fix the P0101 on a Nissan . Send me where I can contact you
@OzMechanics9 күн бұрын
Are they in Texas ? Also do you own a autel scan tool ?
@rafaelmartinez69109 күн бұрын
Yes. I do have it but i don’t want to renew the membership because I don’t do mechanic full time job. Thanks. Yes he is here in Dallas
@marcelinogonzalez87519 күн бұрын
Capppppppp
@OzMechanics9 күн бұрын
Awwww man you found out this was a cap 🧢. For your time you are rewarded a virtual cap 🧢 congratulations. Keep up the amazing work
@dana44ism10 күн бұрын
If I was a mechanic, I would have checked all the doors and the tail gate hatch back to make sure that was the only door that needed a new switch.
@rayp.45410 күн бұрын
Visual inspection for the win! Nice diag Oz.
@codyrahn682310 күн бұрын
U are a life saver sir
@Csupaks1011 күн бұрын
Perfect video! do you have the link for the Topdon tool you are using in the video? thanks!!
@OzMechanics10 күн бұрын
They sell them on www.topdon.us It’s an amazing tool, highly recommend
@harryfatcat11 күн бұрын
Nicely done.
@Mr2004MCSS11 күн бұрын
Cylinder 1 was also misfiring. Was the wire for this cylinder also compromised?
@OzMechanics11 күн бұрын
The way that the module finds a misfire is from the speed of the crankshaft sensor. So at points a major misfire on one cylinder might affect the other cylinders to show false misfires
@Mr2004MCSS11 күн бұрын
@@OzMechanics Ok, thanks.
@LSabiston-gz5ks11 күн бұрын
I am currently driving in silence. Mainly because I hadn't checked anything. My screen flashes RAM but the back up camera and radio don't work. I just checked this delightfully hidden fuse (thanks for that). I looks good. So damn. I'm too cheap to take it to the dealership. Suggestions?
@cespedartificial367011 күн бұрын
friend, 3 years after you published this video and it still continues to save the lives of many people, thank you very much, very well explained and very well done, friend, it is my first ram that we bought and I was crazy thinking that the radio had already been ruined by complete but you saved us thank you 🌟
@mikechiodetti448211 күн бұрын
Good find! Have seen similar problems on Ford "F" Series truck harnesses. Good video!