same pb 4 me

Great video! Sounds ike PO just didn't want to deal with his issue, can't believe he rode it like that. Glad you got it fixed, very informative.👍

After all this time is it still going strong?

Do you have to remove the tank to remove the cables ?

Any sbujsting welcome

Here's my projust is putting a 50 cc mini bike motor with kick start done with the pedaling crap

Video 🚮

You couldve at least fast forwarded parts of it

😂 i bet she was talking shit

Do you have the rough textured transfer case? If so how do you clean yours?

U managed to make changing a fender look hard

What's the difference between yours Progressive Suspension 11-1527 18.5 Progressive Rate Fork Spring,Black verses the 11-1577 that only shows on their website for a 2019 Harley 883?

What sissy bar do you run ?

Took my cable out and now it won’t thread back in at all, I can literally slide it in and out without threading it, not sure what change 🤔

So this is a ridiculous question but where does the hot wire hooked to the starter go? Because this sportster I just picked up has another one that goes to the harness and the one on the starter. Do they go on the same battery terminal or what?

Can i have the wheel brand

oetiker clamp, at HD engineering they pronounce it "OH-Ticker" clamp. My friend has 2012 "Forty-Eight" XL1200X. This is the same place his is leaking, thanks for the video.

My 04 fatboy is only clicking, and the battery is charged. Idk whats going on. This is the first video on my quest to diagnose.

I was told that the 1200 tank would not fit a 883 so ty for this.

Does the rear bar interfere with mounting and dismounting the bike or back up the back ?

I was 4K miles into mine, “break in period”. The seat is garbage and uncomfortable for anything longer than an hour. You might as well be sitting on a brick. DO NOT BUY

What is the hose called that is next to that one and looks similar and loops under and upwards and has a plastic cap in the end?

Was it hard to get the exhaust hanger bolt out, I don't want to break it. Any suggestions? Tia

Try the minimum AMT of primary fluid

I have a 2021 sporster 883, think if i buy the gauge speedometer mount you did, it would still work for my sporster? I was also planning on doing a road warrior fairing on it, think it would still work?

Would it be a good idea to wrap the hose w EZ fuse tape? Same thing ppl use on the wire tuck

Academy on I-10

I don't trust all relays,you never know if someone bought one & returned the bad one,Id have got another one. Not much annoying then tearing apart anything just to replace Junk & need redo again. Hope ur bikes better. ✌

Did you paint the SDC logo black bc all the sdc seats comes with white logos. I called and it can’t be custom ordered/changed from saddlemen.

Remove battery it's makes it easier

did you custom order the black logo?

Mine clicks when i first start it up after not running it for a week. the first start it clicks then the second it starts right up. After i ride it around any start ups it acts normally. What do you think it is? The relay? Or just a battery slowly dieing?

Looks like that thing hadn't been parked indoors since it left the dealership. What a shame. But great job reviving the beast!

Have you got the old Dyna 39mm front end or new Dyna forks 49mm?

I only put my rain sock when it's raining. I put a powder sock on my snowmachine and it restricted the air flow massively.

Metti olio 85w140

watching you load that thing was the most stressful experience of my life, not even bested by a time I almost sent my buddies truck off a 30 foot ridge

good job looks much better

Clutch hub bearing in the clutch basket

Part number ?

It could be your compensator going bad.

what year of bike ?

I just installed a Barnette extra plate clutch pack and heavier clutch spring in my 2006 Electraglide. The pull on the clutch lever was brutal so I installed a Muller power clutch, now the lbs. pull is about the same as the OEM clutch ramp assembly was but now I can't find neutral. I've gone back and set both the adjustments at the pressure plate (1/4 turn)and the cable (Just 1/8" free play). That's as close as I think possible without compromising the throw-out bearing (having it constantly engaged), but still no luck. If I could find a clutch lever that stood out from the grip a bit more, it would afford me a bit more length of pull that I'm sure would fix this but I still haven't found one. Also, I like to use two or three fingers at the lever, now I can't because my little finger gets pinched between the lever and handle grip and robs another quarter inch of lever travel. Suggestions?

Front 19” and the rear 17”?do yoy need to change both bushing?

What size for your fromt and rear wheel sir?brands?

Dude thats a carb tank not fuel injected

Hi, do the attachments come with the sissy bar, or bought separately? If so, what’s the part number? Thanks.

I've had this seat with the back rest on my 23 LRS for about 2 weeks. Although the backrest is phenomenal and the reason I got the seat the seat is a little on the firm side. I thought you would mention whether that initial firmness softens somewhat and after how long.

replace the starter.....you will be out somewhere with no hammer and it wont start trust me i know from experience..2007 1200l stood on the side of the road for hours waiting for a rescue

Did you run "bolt on" cams on your XT? If so, what did you go with?