Hello , thanks for this video. Could you please do a tuto for an rfid ub031 . if it use i2c protocol instead of SPI, and could it wired directly in SDA, SCL, 5V and ground without resistors or usb debugger like you didi in this video . with documentation to run it please if possible. Thanks in advance for sharing

Hi how much is the time between interrupt(falling or rising edge) and function in normal case and how we can decrease this time ? (Doing the function immediately after interrupt without any delay)

عاشق لهجه ایرانیت شدم

it only transmits data sometimes when I press the reset button. what could be the problem?

when i connected this way in hardware board , its showing target is not connected,why? pls help

Which pins on the board did you use for the switch?

can you please share the code?

Hi, I added your library and could try to make it but, There is no reaction. It doesn't read the card at all. I really want to do it but can you help me? I really don't understand what the problem is. It's been several days.

God bless you. That was just amazing, saved my looooong RFID struggles. Thank you very much, it's hard to find something portable and WELL described, documented :)

Thanks for the clear explanation :) I was trying to figure out uid of my tags (according to your explanation) but it doesn't work. It doesn't give me a number, they changed ! Can you help me?

I have a question, in your code, you initialized PIN A4 (SPI1_NSS) as GPIO output with initial value of "low" and connected this pin to PB12 (SPI2_NSS), does this mean the NSS is always pulled low and the SPI protocol is always transmitting?

Dude, you are a lifesaver! your .h and .c files are working really well. Maybe that was my fault but I couldn't find lib. which is working well. Thank you so much

Hello, where did you get the information about RFID RC522? Kind regards

Please help me, I can't read my serial number

کارت عالی بود و لطفاً ادامه بده امیدوارم موفق باشی مرد. بهترین هارو داشته باشی.

hi, can you please provide me the code

Thanks a lot!!!

Greaat

hello sir can i have the code you used for transmetting and receiveing the data?

بسیار عالی. لطفا باز هم ویدیو های آموزشی بذارید

Hello does anyone have the code for this file? and can someone help me in using rc522 with STM32L072CZTx.

Hi, thank for you presentation! Please, how can i download the library? The provided link seens to be broken.

Thank you for not using Arduino. almost all the tutorias are based on Arduino which never shows the low level code. Thanks for explaining the Checksum.

Nice ❤❤❤❤❤❤❤

Hello, i sended request drive access . Thank you

can you give me access to your drive please thank you. ps. I need to use with STM32L152RB does anyone have any suggestion please.

Hello, i would like see your code, i sended request drive access .

thank you so much for your stm video series. It is very rare that someone also explains the driver. Please keep on making more of these, your help is very precious to many people and even companies! More power to you!!

how many ohm resistor?

please give me access to your source code

Dear sir,it's very good detailing .can you please provide the code

Hi. May I please ask you for an access to dowload the libs? Thanks.

Spi + fatfs

I wanted to download this code, but I not have a access to google drive. Can you help me? Please

Please check the diver link again, it doesn't seem to work.

خیلی ممنون از توضیحاتتون مهندس

یکمی رو خونی تمرین میکردی بد نبود

is this work with stm32f466re ?

Dear Sir. The audio track is very low.

Entjungfert

can you help me with code if i control with 2 buttons and 2 outputs

can u plz share the code?

excellent explanation, thanks

hello sir can i have the code you used for transmetting and receiveing the data?

Very helpful video, Thank You Sir :)

I don´t know why, but the status is always staying in 2 (MI_ERR) and all the connection are correct. Do you have some advice?

Hello. Thank you so much for your really clear explanation. I'm interested in getting your code in order to implement it in a graduation project. I requested the access on google drive. Could you accept it please ? Have a nice day and, once more, thank you for your great work

Hello can you give me access to the drive or can you send me the files? please.

Hello. Thank you so much for your really clear explanation. I'm interested in getting your code in order to implement it in a graduation project. I requested the access on google drive. Could you accept it please ? Have a nice day and, once more, thank you for your great work

Hello sir, kindly provide access to your google drive. Thanks in advance.