10 cents Tip: sand rust, remove dirty grease underneath and prime and spray. Finish off topcoat over the zinc plate to stop next years rust. ReApply grease 15 cents Tip, nylon nut is one time use. In future, use a new nut each time removed.
@TheS197King5 ай бұрын
My scag is leaking oil from a cover held on by 4 nuts on the back side of the motor and for the life of me i cant figure out what they part is called to look it up abd get any farther smh..Any ideas?its literally right dap center of the motor that would be facing toward your shins.
@j1207726 ай бұрын
Thank for sharing
@alliemccleary48007 ай бұрын
Thank you for this!
@TheAti2d7 ай бұрын
The diagram shows the plate going before the last spring. The company needs to fix that before they kill someone
@KeithLewis-k1c10 ай бұрын
You have blow by. You have rebuild the motor or get another motor
@whatRU5 Жыл бұрын
Confused. That package shows the plate fitting on before the last spring & nut. But you put the plate on after the spring. Why?
@Whissht Жыл бұрын
This video save me money 💰
@Whissht Жыл бұрын
Thank you
@DragonSelena1976 Жыл бұрын
Very helpful. Need to replace another piece on 2009 Chevy Cobalt 🤦🏽♀️ Great car but freakin A! Always something going on with it
@shanedonaldson56038 ай бұрын
Amen. Feel like I’ve replaced everything on my cobalt so far and I’m only at 120k miles. 😑
@johnpoulson384 Жыл бұрын
Thanks. Sometimes the simplest of things 🤪
Жыл бұрын
Thanks for the information. You made the installation super simple and I was able to follow your steps to a tee and do it myself 🙏 😊
@JimBliss-l7u Жыл бұрын
Mine, symptoms were, running rough and blowing oil out the exhaust. It was seeping a little oil under the shrouds and collected crud blocking airflow cooling the left cylinder. Overheated. Melted the valve guide, stuck the exhaust valve, bent the valve, smacking the piston, bent the pushrod, and of course the valve guide slid into the combustion chamber as far as the valve would allow it. And warped the head. I bought a used head. Cleaned it up. Straightened the pushrods, lapped the valves and replaced the valve guide seals. That head was warped too so I flattened it with sandpaper on glass. The new used head immediately slid the valve guide into the cylinder and blew the valve guide seal off. SO I removed the valve guide, beat the crap out of it with a framing hammer and pounded it back in the head. I did a leak down test last week and it was hissing out the exhaust so I ordered a valve. Tore the thing down and the guy sent me the wrong valve. So I lapped the valves and put the thing back together. This mower has to work every day. Healthy or not. Right now the engine runs like crap, blows smoke, fouls the left plug and uses oil. But, there is no blow-by. HMM. Let me think about this. There is no blow by coming out of the tube that goes into the intake but if you pull the oil filler cap it blows oil all everywhere. I just got a compression tester so Ima go test the compression right now. This engine has been working sick at least 800 hours,.
@jimhenderson2308 Жыл бұрын
My did the exact thing. Piece of garbage cobalt
@billtribble7197 Жыл бұрын
i had a 2inch coupler with a bad latch. all i could find locally was a 1&7/8". works perfect on a 2" or a 1&7/8. ball hitch now
@davidmarks5400 Жыл бұрын
Mine cracked the same way and I put JB weld on it until I could order the part off eBay,then watched this video on how to install. I have to replace the other side as well.Hooray for You Tube tutorials and eBay.
@Intuition_Like-A_River Жыл бұрын
Thanks for this video. My dad is gonna help me w this one. Shouldn’t be too complicated!!
@Intuition_Like-A_River Жыл бұрын
Dad helped me and we got it!! Thanks for the informative video!!
@wildwoodtop Жыл бұрын
Nice job Son! 👍
@geraldharper364 Жыл бұрын
Thanks just what I needed
@thankswillie Жыл бұрын
strong arm lol, ,probably low compression...
@julienplouffe1170 Жыл бұрын
Helped me out so Much! Thanks man
@RobCarstuff9112 Жыл бұрын
My signals don't cancel. Will this fix the issue?
@hoffmanhandymanservice8292 Жыл бұрын
It could I think. I'm not entirely certain.
@RobCarstuff9112 Жыл бұрын
@@hoffmanhandymanservice8292 Hello, It did (:
@jacobt10031978 Жыл бұрын
The switch replacement did not fix my non cancelling signal.
@wcjcnc Жыл бұрын
Wow. I see several people saying to pull the heads and inspect the head gaskets. Lol. You can perform a cylinder leak down test in a few minutes. No need to pull the heads.
@jefflee036 ай бұрын
this lol so many people quick to get into a big job instead of doing proper diagnosis
@eazyev922 жыл бұрын
I’ve been looking for a way to mount a rack without having to screw into the beams in my storage unit. great idea with the clamps and the plywood! I’m gonna make something similar.
@horseman622 жыл бұрын
thank you! just what I needed to see!
@hillbilly2141tn2 жыл бұрын
Thanks for the vid. I just hit mine with the mower and launched the lever across the yard. I was worried I was gonna have to replace the whole tounge! Good info!
@Adriva012 жыл бұрын
Everything is great. But...it looks like you still have some wobble on the ball even after the second try. Maybe the nut should be a little bit tighter (?)
@anthonyrabaiotti50152 жыл бұрын
Your video guided me through perfectly Glad I had two hands and a nifty little 2 way Rachet Thank you 😊
@hoffmanhandymanservice82922 жыл бұрын
Glad to help! That's what it is all about. 😉
@tryduck69932 жыл бұрын
Looks like its been replaced once already judging by the prying marks on the plastic and not fitted together properly
@hoffmanhandymanservice82922 жыл бұрын
I think it had been too. Also, the one that I took out was really flimsy plastic compared to the stock one I put back in. Probably why it broke to begin with. 😕
@nicosends2 жыл бұрын
having trouble getting the ball in after replacing… all 2” so idk what the problem is
@acbivens8729 Жыл бұрын
I have heard that them replacement go by weight and if u get the wrong weight size even all 2 inch it won't let the ball go in
@davidf96302 жыл бұрын
Just a crazy question about your installation. Would it be easier to thread the nut if you took the tension off the lever ( open it)?
@franciscogama9302 жыл бұрын
Semi-unrelated, but was your ball loose and was that part of the plan?
@Pedroluvslupe2 жыл бұрын
Any idea why the power washer loose water pressure? Mine acts as this one
@Laura102319693 жыл бұрын
Thank you!!! I’ve watched several videos and yours is the first to explain that the hook needs to go over the bar on the underside of the hitch.
@erichines27813 жыл бұрын
It's either ur rings going bad or u got a bad head gasket on a cylinder
@americanland8783 жыл бұрын
Wiper switch replacement on the other side just as easy. I pulled the bottom halves out and lifted up on the top piece. The right-side trim piece I pulled out and then replaced the switch unit. Great video saved me some labor costs.
@RayAalster3 жыл бұрын
Look for the breather that ventillates the crankcase. If it is blocked it might cause your rough idle and blow-by too. Older engines are not blowing the fumes to the intake breather. They usually blow the fumes to the atmosphere. If you know someone with a compression tester get that done. If all else fails get some oil that is used for older motors. It is formulated to have less blow-by.
@gunsgunsnbullets3 жыл бұрын
thank you excellent
@billiethorne91453 жыл бұрын
Thank you for helping us old folks
@clydetheglide41983 жыл бұрын
What did you run over it for? Just saying I just ran over mine
@ryanretzlaff48603 жыл бұрын
Thanks for the great video. It was a lot more simple then I imagined.
@gonzalo10423 жыл бұрын
Wow you saved me!!! Thank you Sir! I fumbled for 2 days trying to figure it out. I’m sure you have helped countless people. Gracias. Gonzalo/Miami
@mykemorris13 жыл бұрын
Thanks. Very helpful for a (should be) simple) fix.
@parnellmahoney78313 жыл бұрын
I had to remove the rectangular washer altogether in order to have enough threading showing on the bolt (1 - 1&1/2 threads) to satisfy the safety warning. Think that's okay? I'll be checking it periodically to see if it needs tightening per the instructions and saving the washer in case there's room for it down the road after usage. Also my ball clamp sticks even when I unlock the coupler lock - I have to jiggle it extensively to get it to disengage. Not sure why.
@chadmann81943 жыл бұрын
Rings
@lolecksuburbs37663 жыл бұрын
Hey I’m not sure anyone else noticed this or not but your towing ball is loose. The nut that holds it on you can see moving back and forth in your video. Not good. i think my dad commented this because this was not me XD
@debciszewski74583 жыл бұрын
Awesome, thanks much, great video!!
@itzz_tucka46703 жыл бұрын
Could u tell me what Kawasaki engine model that is? And what year?
@budgortner79103 жыл бұрын
You have one of 2 problems first I would look at is pulling the heads and check out the head gaskets from there if the head gaskets don't show signs of seapage then I'd say bad Ring's.
@jefflee036 ай бұрын
more than 2 things could be wrong here there is valve guides that could drop and seals that could go bad, Valve worn where it rides in guide at, it could be a crank breather clogged, valves have carbon build up on them, all kinds of things and why pull heads when a test can show you if the heads need to be pulled or not. This is proper diagnosis: get a leak down tester and test the condition of the rings and of the head. If you hear air in the crank case good chance it is rings if it is coming from intake or exhaust pull head and see whats wrong with it.
@michaelnesbitt42603 жыл бұрын
I’ve had Kawasaki engines do this before , it’s because they’ll run well even when they’re worn out and need to be rebuilt or changed completely. Also Kawasaki valve guides slip when they wear out and the heads have to be replaced . It can cause exhaust valves to bend and be stuck open